Ortech OE-126 User manual

WARNING
LED Exit Signs
MODEL OE-126
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or use of this product, consult a competent electrician.
WARNING — THE INSTALLATION MUST BE CARRIED OUT BY
A QUALIFIED ELECTRICIAN.
1. LED Exit Signs are suitable for indoor use only. DO NOT use outdoors
2. Please keep the LED Exit Signs away from any corrosive substance
3. LED Exit Signs can only be installed by a qualified electrician
4. Before installation or maintenance, please disconnect the power at fuse or circuit breaker to
prevent electric shock
Instruction Manual
1-888-543-6473
1-888-541-6474
13376 Comber Way
Surrey BC V3W 5V9
[email protected]
www.ortechindustries.com
375 Admiral Blvd
Mississauga, ON L5T 2N1
CAUTION
Application Notice
1. All electrical connections must be in accordance with local codes, ordinances and the National Electric code
2. DO NOT mount in hazardous locations, or near gas or electric heaters
3. DO NOT let power cords touch hot surface
4. Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel
5. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition
6. DO NOT use LED Exit Signs for other than intended use
7. Allow battery to charge for 24 hours before first use
INSTALLATION GUIDE
AC Wiring
1. Connect the WHITE wire to NEUTRAL
2. If using 120V, connect the BLACK wire to the hot lead
3. If using 347V, connect the RED wire to the hot lead
4. Cap the unused lead
MAIN
PCBA
JK2
TRAN
Batt1
Battery
AC Input
Red 347V AC
Black 120V AC
White NEUTRAL
LED Strip
Canopy Assembly
1. Insert canopy into housing at 20° and twist
2. Quick snap is now locked firmly
3. Trying to remove when canopy is locked in place
may cause damage
Wiring Diagram

INSTALLATION GUIDE
LED Exit Signs
MODEL OE-126
Mounting Instruction
The fixture is suitable for wall mounting, side mounting, ceiling mounting.
1. Open front cover by blade screwdriver (see Fig.1 below)
2. Knockout appropriate mount screw hole and cable hole, mount back plate on the wall after feed building AC supply cable into back plate
(see Fig.2 below for more details)
3. For ceiling and side mounting purpose, remove the mounting hole cover on the top or side of the unit (see FIg.2,3,4),
assemble the canopy on the unit (see Canopy Assembly diagram on page 1 of this instruction manual)
4. Attach crossbar to junction box, set the longer blade of crossbar touching the J-Box
5. Route the proper wires through mounting hole out of housing
6. Make electrical connections inside the J-Box like the wiring diagram on page 1 of this instruction manual
7. Push excess wire into J-Box, use screws to tighten canopy to crossbar so that canopy is securely fastened and tight against the wall
8. Attach battery connector to PC board, restore front cover on unit
9. If pictogram direction assembled not suitable, pictogram can take out for change direction or replace pictogram, and then insert into the
diffuser easily (see Fig.5)
Instruction Manual
1-888-543-6473
1-888-541-6474
13376 Comber Way
Surrey BC V3W 5V9
[email protected]
www.ortechindustries.com
375 Admiral Blvd
Mississauga, ON L5T 2N1
Open Front Cover
Wall Mounting
Side Mounting
Fig.1
Fig.2
Fig.3
Battery
Connector J-Box
Canopy Crossbar
J-Box
Ceiling Mounting
Fig.4
Change Direction of Pictogram
Fig.5
J-Box
Canopy
Pictogram