Ortech ST-PC1025 User manual

WARNING
LED Step Lights
MODEL ST-PC1025
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or use of this product, consult a competent electrician.
CLEANING AND MAINTENANCE
WARNING — THE INSTALLATION MUST BE CARRIED OUT BY
A QUALIFIED ELECTRICIAN.
1. LED Step Lights are suitable for using in wet location
2. Please keep the LED Step Lights away from any corrosive substance, and please use dry
cloth when you clean it
3. LED Step Lights can only be installed by a qualified electrician
4. Before installation or maintenance, please disconnect the power to prevent electric shock
Instruction Manual
1-888-543-6473
1-888-541-6474
13376 Comber Way
Surrey BC V3W 5V9
[email protected]
www.ortechindustries.com
375 Admiral Blvd
Mississauga, ON L5T 2N1
CAUTION
CAUTION
Application Notice
1. All electrical connections MUST be in accordance with local and National Electrical Code (N.E.C) standards
2. Remove fixture and mounting components from the box, and make sure that no parts are missing by reading the instructions carefully
3. Turn power OFF before installation, inspection, or removal. Use all necessary precautions while performing this procedure
4. Consult a qualified electrician to ensure correct branch circuit conductor. Minimum +90°C supply conductors
5. Properly ground electrical enclosure. It is imperative that the outlet box is properly grounded
6. DO NOT reverse the hot and neutral connections, otherwise safety will be compromised
7. The integrated LED fixture has no lamp / bulb to replace
8. Use UL or IEC approved wire only for input/out connections
Ensure that the fixture temperature is cool enough to touch.
DO NOT clean or perform maintenance while fixture is energized.
•Clean lens and fixture with non-abrasive cleaning solution
•DO NOT open fixture to clean LED. DO NOT touch the LED
•DO NOT spray liquid directly onto LED, LED driver or wiring
TROUBLESHOOTING
CAUTION
•Check to see if the line voltage at the fixture is correct
•Ensure that there is voltage at lamp fixture wires. If there is no voltage, then check all connections
•Check to see if the fixture is grounded properly
If fixture does NOT light up:
•Check to ensure that there are no defects
•Check fuse / circuit breaker for trips, then check wiring connections

Hardware Contents
INSTALLATION GUIDE
LED Step Lights
MODEL ST-PC1025 Instruction Manual
1-888-543-6473
1-888-541-6474
13376 Comber Way
Surrey BC V3W 5V9
[email protected]
www.ortechindustries.com
375 Admiral Blvd
Mississauga, ON L5T 2N1
ORTECH reserves the right to modify at any time, without notice,
any or all of our product's features, designs, components and
specifications to meet market changes.
Outlet box
(not included)
Live wire
(Black)
Wire connector
(A) Mounting plate
Hexagon socket screw
(C)
Grounding
Wire
Naught
Wire (White)
Mounting
Screw (B) Face Plate
(Outdoor using) After installing the fixture,
caulk the connection between face plate and
wall by adhesive glue to prevent water
seeping into the outlet box.
1) Connect the wires of the fixture to wires on the outlet
box with wire connectors (A), WHITE to WHITE, BLACK
to BLACK. Loosen the GREEN screw in the mounting
plate and then twine the GREEN line of the fixture to
the GREEN screw, then secure it
2) When wires are connected, tuck them carefully inside
the outlet box and attach the mounting plate to the
outlet box by using mounting screws (B)
3) Make sure that the mounting plate is at the same
height as the wall. Assemble the face plate onto the
mounting plate and tighten the hexagon socket nut
with the Allen Key (D)
4) Restore power at fuse box / circuit breaker. Check the
operation of integrated LED fixture
5) Installation is complete