OSP furniture Designlab ADP6328GD User manual

IMPORTANT-PLEASE KEEP THESE INSTRUCTIONS IN CASE OF ANY CUSTOMER SERVICE ISSUES
© Office Star Products September 2020
ADP6328GD (LF)
ADAPTOR 63” GAMING DESK
ASSEMBLY INSTRUCTIONS
OSP FURNITURE LIMITED PRODUCT WARRANTY
Design Lab Products
• 3 years on gaming desks and chairs
• Upholstery is not warranted against routine scratching and scuffing
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
year warranty on all parts applies. Fabric and foam is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty
will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
WARNING
1. Use this product only one person at a time.
2. Do not use this product unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts screws and knobs are tight every three
months or as needed.
4. Dispose of packing material properly. Do not use plastic cover as
head covering. It may cause suffocation.
5. Do not use product as a stepladder.
6. Use this product for its intended purpose only.
7. Use mild detergent only for cleaning.
IMPORTANT-PLEASE KEEP THESE INSTRUCTIONS IN CASE OF ANY CUSTOMER SERVICE ISSUES

180°
PROPER CAM-LOCK INSTALLATION
HARDWARE LIST
NO DRAWING DESCRIPTION SIZE QUANTITY
AGlue 1 PC
4 PCS
8 PCS
8 PCS
12 PCS
12 PCS
4 PCS
2 PCS
8 PCS
Wooden Dowel
Cam Screw
Cam Nut
Allen Bolt
Allen Bolt
Wood Screw
Wood Screw
Flat Allen Bolt
Ø
Ø
Ø
Ø
6 x 12 x 12mm
6 x 25 x 12mm
3.5 x 12 x 6mm
4 x 12 x 8mm
6 x 32 x 10mm
1 PCAllen Wrench Ø
B
C
D
E
F
G
I
J
H
(1) Top Shelf (1 PC)
(3) Left Side Frame (1 PC)
(5) Back Panel (1 PC)
(7) Rear Lower Crossbar (1 PC)
(9) Rear Frame (1 PCS)
(2) Desk Top (1 PC)
(4) Right Side Frame (1 PC)
(6) Middle Front Crossbar (1 PC)
(8) Upper Crossbar (1 PC)
(10) Upper Left Frame (1 PC)
(11) Upper Right Frame (1 PC) (12) Accessory Hook (1 PC)
PARTS
Phillips screwdriver also needed for assembly (not provided)

Remove all the parts from carton, separate them into part numbers indicated on the list and make sure part quantities are correct.
STEP 1 Screw in four Cam Bolts (C) into bottom of Desk Top (2). Screw in two Cam Bolts (C) into both Left Side Frame (3) and Right Side Frame (4).
FULLY TIGHTEN CAM BOLTS (3). Insert four Wooden Dowels (B) into Back Panel (5). Use a small amount of Glue (A) per hole, be careful not to over fill hole.
Note: Using a rubber mallet, gently tap Wooden Dowel (B) to ensure it is sitting properly.
C
C
C
4
3
B
5
2
STEP 1
(13) Cup Holder (1 PC)
(15) Power Outlet (1 PC)
(17) LED Power Supply (1 PC)
(14) Wireless Charger (1 PC)
(16) Remote Control (1 PC)
(18) Storage Tray (1 PC)
PARTS ADP6328GD (LF)
ADAPTOR 63” GAMING DESK
ASSEMBLY INSTRUCTIONS

STEP 2 Attach Back Panel (5) between Side Frames (3 & 4) and secure using four Cam Nuts (D). FULLY TIGHTEN ALL CAM NUTS (D). Attach Middle
Front Crossbar (6) between Side Frames (3 & 4). and secure using four Allen Bolts (F). DO NOT FULLY TIGHTEN ALLEN BOLTS (F).
STEP 3 Carefully turn assembly to the upright position. Attach Rear Lower Crossbar (7) between Side Frames (3 & 4) and secure using two Allen Bolts (F).
DO NOT FULLY TIGHTEN ALLEN BOLTS (F).
ADP6328GD (LF)
ADAPTOR 63” GAMING DESK
ASSEMBLY INSTRUCTIONS
ADP6328GD (LF)
ADAPTOR 63” GAMING DESK
ASSEMBLY INSTRUCTIONS
D
D
3
4
5
6
F
7
3
4
F
STEP 2
STEP 3
STEP 4 Attach Desk Top (2) to assembly. Secure Desk Top (2) using four Allen Bolts (F) for Side Frames (3 & 4), four Cam Nuts (D) for
Back Panel (5) and four Allen Bolts (G) for Middle Front Crossbar (6). APPLY FIRM PRESSURE TO ALIGN & FULLY TIGHTEN ALL CAM NUTS (D)
AND ALLEN BOLTS (F & G).
STEP 5 Attach Storage Tray (18), Cup Holder (13) and Wireless Charger (14) to Desk Top (2). Secure Power Oulet (15) to Desk Top (2) using two Wood
Screws (I). FULLY TIGHTEN WOOD SCREWS (I).
F
G
2
18
D
14 15
I
2
13
3
4
6
STEP 4
STEP 5
5

STEP 6 Secure Rear Frame (9) to rear of desk assembly using four Allen Bolts (G). Secure Upper Left Frame (10) and Upper Right Frame (11) to rear of
desk assembly using two Allen Bolts (G) for each upper frame. FULLY TIGHTEN ALL ALLEN BOLTS (G). Secure Accessory Hook (12) to right side of desk
assembly using two Wood Screws (H). FULLY TIGHTEN WOOD SCREWS (H).
STEP 7 Secure Upper Crossbar (8) between Upper Frames (10 & 11) using two Allen Bolts (F). FULLY TIGHTEN ALLEN BOLTS (F).
ADP6328GD (LF)
ADAPTOR 63” GAMING DESK
ASSEMBLY INSTRUCTIONS
H
12
G
10
9
G
F
11
8
8
G
STEP 6
STEP 7
STEP 8 Secure Top Shelf (1) to upper frame assembly using eight Allen Bolts (J). FULLY TIGHTEN ALLEN BOLTS (J). Secure Top Shelf (1) to Rear
Frame (9) using two Wood Screws (H). FULLY TIGHTEN WOOD SCREWS (H).
STEP 9 Connect LED Power Supply (17) to cord of Top Shelf (1).
ATTENTION: MAKE SURE ALL CAM LOCKS, BOLTS & SCREWS ARE FULLY TIGHTENED BEFORE USING DESK.
ADP6328GD (LF)
ADAPTOR 63” GAMING DESK
ASSEMBLY INSTRUCTIONS
STEP 8
H
1
J
9
STEP 9
17

SAFETY WARNINGS - PLEASE READ FIRST
DIY 1
RGBW
DIY 2DIY 3
QUICK
SLOW
AUTO
FLASHDIY 4DIY 5DIY 6
FADE7JUMP3JUMP7 FADE3