Osram OPTOTRONIC OTe 18/220-240/500 PC User manual

OPTOTRONIC
®
OTe 18/220-240/500 PC
500mA Constant Current LED Power Supply with Phase Cut functionality
2014-4-29
AA6268600DG
OSRAM AG
www.osram.com
Steinerne Furt 62, 86167 Augsburg, Germany
No. 1, North Industrial Road
528000 Foshan Guangdong, P.R. China
1. Technical Data
Nominal Voltage 220 – 240 Vac Output Voltage 18 – 36Vdc
Input Voltage 198 – 264 Vac Maximum Output Voltage 50Vdc
Line Current, nominal 120mA @ 230 Vac Nominal Output Current 500mA DC +/- 10%
Mains Frequency 50 / 60 Hz Typ.dimming range* 10 - 100%
Power Factor 0.95 @ 230 Vac Ambient Temperature -20°C to +55°C
Maximum Output Power Pmax 18 W Max. Case Temperature at tc +75°C
IP Rating IP 20 Max. Output Cable Length 2m
* Suitable for use with electronic leading and trailing edge dimmer
2. Connection Schemes
2.1 LED modules in series:
LED modules should be connected in series.
2.2 Parallel connection on the secondary side is not allowed
CommonCathode prohibited Common Anode prohibited
The installation of two or more OPTOTRONICOTe 18/220-240/500 PC Power Supplies with common
“-“ or “+” wiring by the intention to save wire to LED modules is prohibited, in order to avoid exceeding
the maximum allowed system touch current levels on the accessible parts of the installation.
OTe 18/220-240/500 PC
220 - 240V
A
C
+
-LED Module
2
220-240V
AC
OTe 18/220-240/500 PC +
-
LED-Module
500mA , 9W-18W
OTe 18/220-240/500 PC +
-
LED-Module
500mA , 9W-18W
OTe 18/220-240/500 PC +
-
LED-Module
500mA , 9W-18W
2
2
2
2
2
2
220-240V
AC
OTe 18/220-240/500 PC +
-
OTe 18/220-240/500 PC +
-
LED-Module
500mA, 54W
OTe 18/220-240/500 PC +
-
2
2
2
220-240V
AC
OTe 18/220-240/500 PC +
-
OTe 18/220-240/500 PC +
-
OTe 18/220-240/500 PC +
-
to LED
to LED
to LED
2
2
2
220-240V
AC
OTe 18/220-240/500 PC +
-
OTe 18/220-240/500 PC +
-
OTe 18/220-240/500 PC +
-
to LED
to LED
to LED

OPTOTRONIC
®
OTe 18/220-240/500 PC
500mA Constant Current LED Power Supply with Phase Cut functionality
2014-4-29
AA6268600DG
OSRAM AG
www.osram.com
Steinerne Furt 62, 86167 Augsburg, Germany
No. 1, North Industrial Road
528000 Foshan Guangdong, P.R. China
3. Wire and Connection
Ensure that the LED module load is within the range of rated voltage, current and power supply (see
Technical data)
The luminaries’ manufacturer is responsible for providing the required clearance and creepage distances
and also for the protection against electrical shock, especially for the line and load wires.
Wiring Preparation:
4. Earth Connection
OTe 18/220-240/500 PC is a “Protection Class II” power supply, therefore ground connection is not
required
5. Mounting and Environmental protection
The control gear is a built in type for luminaire integration; an optional cable clamp is available for
independent installation; proper cables should be used.
Maximum permissible ambient temperature must not be exceeded. Make sure there is adequate space to
avoid heat build-up. In critical installations, the temperature at tc point should not exceed the declared
value.
6. General note
Power supplies must be installed by qualified electrician
Disconnected from mains supply before wiring work
Hot plug-in or secondary switching of LEDs is not permitted, as it may cause a very high transient current
to the LEDs
For further information, please refer to “OPTOTRONIC -Technical guide” at www.osram.com
Proper and safety usage and installation of the product shall comply with product
datasheet and OPTOTRONIC Technical guide. The latest documents are
available at www.osram.com