Otto Wilde GRILL STAND XL User manual

ASSEMBLY INSTRUCTIONS
Grill stand for The Otto Grill with slide-out gas bottle drawer and additional storage space
GRILL STAND XL
OTTO’S

WELCOME
TO THE FAMILY
2

THE OTTO GRILL STAND XL
Congratulations on your purchase of Otto Wilde’s Storage
Module and thank you for becoming a part of the grill
revolution. With our Storage Module the name says it all.
They are the perfect option for storing all of your grilling
and outdoor accessories. Much like you find inside in the
kitchen, Otto offers you the option of a cabinet for storing
your larger items or a set of drawers for those smaller items.
With its 100% stainless steel construction it’s the perfect
option to keep you organized and from having to run into
the house to get something. The spacious counter top can
easily be wiped clean due to it also being made of high-grade
stainless steel. The best part of the Otto Grill Stand XL is
the gas bottle storage. With a slide-out drawer the gas bottle
storage is easily accessible for installation and maintenance.
Many of the features were developed with the help of the
greatest community in the world, and now you’re a part of
this community. Thank you for joining the family.
Your Otto Wilde family
3

TOOLS YOU WILL NEED
SCOPE OF DELIVERY
Here is a list of parts that
are exemplary for your
Grill Stand XL. Quickly
check that all the pieces
are there and use the
screws supplied.
1x Base
C
4x Module Connector Screw
40x M5 X 12 Screw 16x M6 X 16 Screw
A
J1J2J3
1x Hex Key 1x Torx Key TX20 1x Torx Key TX15
1x Side Wall Right1x Lower Back Wall 1x Upper Back Wall
! Start all screws by hand
first and then finishing
tightening with the tool
provided or similar.
4x M5 X 10 Screw72x M4 X 8 Screw 12x Screw M4 X 10
B
G D H
4

1x Counter Top
4x Adjustable Castor
1x Toeboard Back 1x Door
1x Toeboard Left
1x Cross Brace Top
2x Rubber Protect Ring 1x Toeboard Right
1x Cross Brace
1x Toeboard Front
1x Gas Bottle Drawer
1x Middle Wall
1x Anti-Tip Support
8x Drawer Slide
1x Drawer Front 32"
2x Door Hinges
3x Drawer Front 16"
1x Side Wall Left
5

1
2
ASSEMBLY
CORE
A
Before installing the
side walls or middle
panel, we recommend
first installing the
drawer slides.
1 x
1 x
A5 x
6

8 x
B32 x
3
Snap the soft-close
mechanism of the rail
forward to tighten the
rear two screws.
KLICK
B
Repeat on the
opposite side.
7

1 x
1 x
4
5
A 5 x
A 5 x
Save one screw
for later.
A
8

A 3 x
A 1 x
A 7 x
6
7
A
9

4 x
C16 x
8
For mobile use these
mounting holes (1) and
for stationary installati-
on use these mounting
holes (2).
Be sure to place the
washers on the screws
as shown here in order
to ensure proper faste-
ning of the castors.
C
12
10

A 4 x
1 x
A 3 x
10
9
A
A
11

A 2 x
1 x
12
11
A
A
12

H 8 x
13 H
It’s best to install the
door hinges, particu-
larly the lower hinge,
before the gas bottle
drawer.
13

1 x
4 x
A 4 x
B 4 x
A 2 x
Repeat on the
opposite side.
ASSEMBLY
GAS BOTTLE DRAWER
1
2
A
A A B
14

3
4
Be sure the lock is in the
in the “up” position and
secured before inserting
the drawer completely.
15

5
Be sure to secure the
drawer by placing the
locking cylinder in the
hole in the floor.
16

ASSEMBLY
TOP
1
2
1 x
A 5 x
A
17

2 x
H 4 x
2
ASSEMBLY
DOOR
B
A
4 x
B 2 x
1
1 x
Be sure to break out
the cover on the side
of the door that corre-
sponds to the opening
direction.
18

4
5
Loosen the thumb screw and
allow the safety support fall un-
til the foot is on the ground.
Adjust the foot as needed by
screwing in up or down.
3
19

3 x
3 x
B 18 x
1
B
ASSEMBLY
DRAWER 16"AND 32"
20