Outdoor GreatRoom Company Sierra User manual

1 | P a g e
Fire Pit Tables
Sierra and Grandstone
Installation Instructions

2 | P a g e
Contents
Contents……………………………………..2
Required Tools….………………………..3
Placing the Table…………………..……4
Gas Connection…………………….…….5
Igniter Installation…………….………...6
Placing the Top…………………………...7
Burner Installation……………………….8
Locating Propane tank………………...9
Door Installation………………………...10
Notice:
This unit is listed for use in North America for both residential and
commercial applications. In the event that the appliance can be
used by those unfamiliar with the appliance, we suggest the use of
a master Key Valve to prevent unauthorized use. The use of a Glass
Guard is also strongly recommended when small children or other
individuals with reduced sensory or mental capacities may be in
close proximity to the appliance.
42430:H 8/20/18

3 | P a g e
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges
found on the coffee table.
One (1) AAA Battery (not
included)
Required for igniter installation for
Crystal Fire burners.
It is recommended that a
minimum of two people
assemble and install fire
pit tables.

4 | P a g e
Placing the Fire Pit table
1. Remove access door
2. Remove the base from the box
3. Move the base without door to desired
location and set into place.
4. When locating your coffee table, refer to the
Crystal Fire manual and maintain clearance to
combustibles.
Before completing the following steps, read and
understand the Crystal Fire owner’s manual.
Sierra fire pit table shown,
finishes and styles may vary

5 | P a g e
Gas Connection
1. Connect the incoming black rubber gas hose
to the valve. It is not recommended to use
Teflon tape or pipe dope on the connection
to the valve with flare fittings.
LP installations use the hose and regulator
provided with the burner.
Natural Gas installations refer to the
supplied Crystal Fire Manual.
Attach incoming
gas here
Use two wrenches to fully tighten gas
connections.
Do not make gas connections to burner until concrete, tile, or
granite top is installed. Gas connections can be made from
below or from above by lifting burner out of top to access gas
line.

6 | P a g e
Igniter Installation
Note: Before installing ignition system, ensure that gas valves are closed
and gas is disconnected for safety.
1. Make sure the valve is in the OFF position
2. Unscrew sparker cap and hex nut (sparker included
with burner). Install as shown below.

7 | P a g e
3. To properly install ignition system, an Ignition and Ground
wire need to be attached to the igniter box.
Start by plugging the black Ignition wire hanging from
the burner in to one side of the back of the igniter
(either side is fine).
Next; plug the Ground wire into the open port on the
igniter box.
Test system by depressing the button on the igniter. A
continuous repeating spark at the igniter on the burner
means everything is connected properly. Consult the
troubleshooting section of your crystal fire owner’s
manual if spark is weak, intermittent, or not present.
4. Once ignition system is grounded and gas
connections are secured and checked for
leaks, set the burner back into its original
position if it was removed during gas hookup.

8 | P a g e
Placing the top
1. With the help of at least one other person, remove
concrete, granite, or tile top from packaging and gently
lower on to your fire pit table base. Construction adhesive
or silicone may be used on the top of the base for a more
stable and permanent placement in heavy use areas.
Burner Installation
Locating your Tank
1.Your tank should be positioned so that the fuel can be
shut off after each use.
2.Slide the tank into the framework past the line shown
below. This is to allow the door to close completely.
3.Confirm all hoses are clear and not touching the burner.
Position tank
behind this line
Lower burner onto base with burner neck facing in the direction of control
panel location.

9 | P a g e
Door Installation
Set door on supports and close. Magnet
will hold door in closed position.
Door support
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
burner, including safety information, proper tightening of connections
with two wrenches and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL BURNER WITHOUT FIRST
CONSULTING THE MANUAL. IF YOU ARE UNSURE OF HOW TO
COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks

10 | P a g e
ENTIONALLY LEFT
AWESOME.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.

11 | P a g e
Notes:
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
_______________

12 | P a g e
© 2015 The Outdoor GreatRoom Company