Outdoor Lifestyles ODCOUG-VFP User manual

Hearth & Home Technologies • Courtyard Vent-Free Conversion Plate Installation Manual • 4150-960 Rev. A • 02/23
This Vent-Free Conversion Plate is designed for use on the
models shown in the chart above. Read these instructions
thoroughly before beginning installation.
ATTENTION!
This kit is designed to convert the Courtyard appliance.
From: CSA/ANSI Z21.97-2017 Outdoor Decorative Gas
Appliance - for outdoor use only.
To: CSA/ANSI Z21.91:20 Ventless Firebox Enclosures for
Gas-Fired unvented Gas Log Type Room Heaters and CSA/
ANSI Z21.11.2:19 Unvented Room Heater, not to exceed
40,000 BTU/HR (11,723 W) – for indoor use only.
CAUTION: Allow appliance to cool completely if it has been
in operation.
NOTE: Gas components are located within the appliance
valve compartment. The Valve Access Cover must be
removed to access components.
KIT CONTENTS:
• (1) Conversion Plate Assembly
• (1) Fastener Pack
TOOL REQUIRED:
Phillips head screwdriver
ACCESSING GAS CONTROL VALVE:
1. Turn o󰀨 gas supply and allow the unit to cool.
2. Disconnect power at GFCI circuit breaker.
3. Remove logs, grate, and media from the appliance.
4. Use a shop vac or small brush to clean debris left after
removal of logs and media to ensure a clean, at sur-
face for the Vent-Free Conversion Plate to sit upon.
5. Remove the Valve Access Cover by grasping cover by
the edges, lift and pull forward out of the appliance. Gas
components should now be accessible. See Figure 1.
Figure 1
Model(s) Kit
ODCOUG-36NR
ODCOUG-VFP
ODCOUG-36TS
ODCOUG-42NR
ODCOUG-42TS
Installation
Instructions
This kit has been tested for use with specic Hearth & Home Technologies products. Check with your local building code
agency before you begin installation to ensure compliance with local codes, including the need for permits and follow-up
inspections. If you encounter any problems regarding code approvals, or if you need clarication of any of the instructions
contained here, contact your Hearth & Home Technologies dealer. For the dealer nearest you, please visit www.hearthn-
home.com.
Courtyard Vent-Free Conversion Plate
Models: ODCOUG-VFP
Appliance
Components
Valve Access Cover

Hearth & Home Technologies • Courtyard Vent-Free Conversion Plate Installation Manual • 4150-960 Rev. A • 02/23
Please contact your Hearth & Home Technologies dealer with any questions or concerns. For the
location of your nearest Hearth & Home Technologies dealer, please visit www.hearthnhome.com.
Figure 4
Figure 3
Figure 2
Rear Cover
Pilot Shield
Pilot Assembly
Bulkhead
Main Burner
Valve Access
Cover
Screws
Burner Assembly
Conversion Plate
6. Remove Rear Cover by removing (3) screws securing
cover to burner assembly. Lift Rear Cover and Pilot
Shield straight up and set aside. See Figure 2.
7. Disconnect incoming gas supply from appliance ex
connector.
8. Disconnect electric from control module.
9. Disconnect wall switch wires from control harness.
10. Remove (4) screws securing burner assembly to the
rebox bottom. Lift the rear of the burner assembly,
slide assembly towards the rear of the appliance to dis-
engage from the bottom of the rebox. Remove burner
assembly from appliance and set aside. See Figure 3.
11. Install Vent-Free Conversion Plate, covering the hole
in the rebox bottom, where the burner assembly was
removed. Secure with (4) screws. See Figure 4.
12. Conversion is now complete.