Ovation C19 User manual

USER MANUAL
Keep this manual for future needs
C19C19
19 x 15W LED aura moving head wash

Table of contents
Caution!������������������������������������������������������������������������������������������������������������������������������������������������ 3
Introduction������������������������������������������������������������������������������������������������������������������������������������������ 3
Safety instructions ������������������������������������������������������������������������������������������������������������������������������� 3
Installation ������������������������������������������������������������������������������������������������������������������������������������������� 4
Read ‘Safety information’ before installing the xture���������������������������������������������������������������������������������4
Fastening the xture to a at surface�����������������������������������������������������������������������������������������������������������4
Mounting the xture on a truss���������������������������������������������������������������������������������������������������������������������4
Securing with a safety cable �������������������������������������������������������������������������������������������������������������������������5
DMX-512 connection/connection between xtures ������������������������������������������������������������������������������������5
Operation ��������������������������������������������������������������������������������������������������������������������������������������������� 6
Addressing������������������������������������������������������������������������������������������������������������������������������������������������������6
Universal DMX Control�����������������������������������������������������������������������������������������������������������������������������������7
Auto run mode������������������������������������������������������������������������������������������������������������������������������������������������7
Sound Mode ���������������������������������������������������������������������������������������������������������������������������������������������������7
Master-Slave Operation ���������������������������������������������������������������������������������������������������������������������������������7
Control Menu Map�������������������������������������������������������������������������������������������������������������������������������� 8
DMX Protocol ��������������������������������������������������������������������������������������������������������������������������������������� 9
Fixture Cleaning ��������������������������������������������������������������������������������������������������������������������������������� 15
Fuse Replacement������������������������������������������������������������������������������������������������������������������������������ 16
Troubleshooting ��������������������������������������������������������������������������������������������������������������������������������� 16
The xture does not work, no light��������������������������������������������������������������������������������������������������������������16
No response to the sound ���������������������������������������������������������������������������������������������������������������������������16
Specications ������������������������������������������������������������������������������������������������������������������������������������ 17

3Version 1.1hotion.com
C19 | LED aura moving head washEnglish
3
Caution!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric
shock when touching the wires!
Avoid looking directly into the light source!
Wear protective glasses and other PPE (personal protective equipment) when working on or near
the xture.
For your own safety, please read this user manual carefully before you initial start-up.
Follow operating safety precautions and pay attention to warning signs methods and equipment
on the user manual.
Indoor use only! To prevent risk of re or shock, do not expose this product to rain or moisture. IP
20 rating�
The ambient temperature must always be between -5° C and +45° C.
Always make sure you are connecting this product to the proper voltage in accordance with the
specifications in this manual or on the product’s specification label.Make sure it is grounded
when using it!
Unplug mains lead before opening the housing!
Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture
and the powercord from time to time.
Make sure to replace the fuse with another of the same type and rating.
Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot
during operation. After use, wait for a cool-down period of at least 10 minutes before handling or
transporting the device.
Every person involved with the installation, operation and maintenance of this device has to
- be qualied
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from the Internet
Introduction
Thank you for having chosen C19. You will see you acquired a powerful and versatile device.
Unpack your item. Before you initial start-up, please make sure that there is no damage caused by
transportation. Should there be any, consult your dealer and do not use the device.
Safety instructions
This fixture is an extremely sophisticated piece of electronic equipment. To guarantee a smooth
operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not
accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the
information printed in this manual.

4Version 1.1hotion.com
C19 | LED aura moving head washEnglish
4
This device has left our premises in absolutely perfect condition. Always disconnect from the mains,
when the device is not in use or before cleaning it. Keep away children and amateurs from the device!
There are no serviceable parts inside the device. Maintenance and service operations are only to be
carried out by authorized dealers.
Installation
Read ‘Safety information’ before installing the fixture
The fixture is designed for indoor use only and must be used in a dry location with adequate ventilation. Ensure that
none of the fixture’s ventilation slots are blocked.
Fasten the fixture to a secure structure or surface. Do not stand it on a surface or leave it where it can be moved or
fall over. If you install the fixture in a location where it may cause injury or damage if it falls, secure it as directed in
this user manual using a securely anchored safety cable that will hold the fixture if the primary fastening method
fails�
Fastening the fixture to a flat surface
The fixture can be fastened to a hard, fixed, flat surface that is oriented at any angle. Ensure that the
surface and all fasteners used can support at least 10 times the weight of all fixtures and equipment to
be installed on it�
Fasten the fixture securely. Do not stand it on a surface or leave it where it can be moved or fall over. If
you install the fixture in a location where it may cause injury or damage if it falls, secure it as directed
below with a securely anchored safety cable that will hold the fixture if the primary fastening method
fails�
Mounting the fixture on a truss
The fixture can be clamped to a truss or similar rigging structure in any orientation. When installing the
fixture hanging vertically down, you can use an open-type clamp such as a G-clamp. When installing in
any other orientation, you must use a half-coupler clamp that completely encircles the truss chord.
To clamp the fixture to a truss:
1� Check that the rigging structure can support at least 10 times the weight of all fixtures and equipment
to be installed on it�
2� Block access under the work area.
3� Fold the legs of the mounting bracket together and bolt a rigging clamp securely to the mounting
bracket. The bolt used must be M10. It must pass through both mounting bracket legs and be
fastened with a self-locking nut.
4� Working from a stable platform, hang the fixture with its clamp on the truss and fasten the clamp
securely.
5� Secure the fixture with a safety cable as directed below.

5Version 1.1hotion.com
C19 | LED aura moving head washEnglish
5
Securing with a safety cable
Secure the fixture with a safety cable (or other secondary attachment) that is approved for the weight of
the fixture so that the safety cable will hold the fixture if a primary attachment fails.
Loop the safety cable through the eyebolt in the back of the fixture and around a secure anchoring point.
Do not loop the safety cable around the fixture’s mounting bracket only, as this will leave the fixture
unsecured if it separates from the bracket.
DMX-512 connection/connection between fixtures
Occupation of the XLR-connection:
1. Group
2. Signal (-)
3. Signal (+)
DMX OUT
1. Group
2. Signal (-)
3. Signal (+)
DMX IN
If you are using controllers with this occupation, you can connect the DMX-output of the controller
directly with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers
with other XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture.
Always connect one output with the input of the next fixture until all fixtures are connected.
DMX-512 connection with DMX terminator:
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,
such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption

6Version 1.1hotion.com
C19 | LED aura moving head washEnglish
6
of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120
resistor connected between pins 2 and 3, which is then plugged into the output XLR socket of the last
fixture in the chain.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120
resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the
last fixture.
Connection with the mains:
The C19 is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC
power source from 100-240 Volts.
This fixture must be earthed. To use the fixture, a plug must be fixed.
The correct assembly of a sufficient plug may be done by professional persons only.
Connect the device to the mains with the enclosed power supply cable.
The occupation of the connection cables as below:
Cable color Connection International
Brown Live L
Blue Neutral N
Yellow/green Earth(Ground)
Operation
The C19 can operate in three different modes. In each mode you can run the fixture as a stand alone
fixture or in a master/slave confiugration. This next section will detail the dif-ferences in the operating
modes�
Addressing
All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture
responds to the correct control signals. This digital starting address is the channel number from which
the fixture starts to listen to the digital control information sent out from the DMX controller. The
allocation of this starting address is achieved by setting the correct number on the display located on the
base of the device.

7Version 1.1hotion.com
C19 | LED aura moving head washEnglish
7
You can set the same starting address for all fixtures or a group of fixtures, or make different address for
each fixture individually.
If you set the same address, all the units will start to listen to the same control signal from the same
channel number. In other words, changing the settings of one channel will affect all the fixtures
simultaneously.
If you set a different address, each unit will start to listen to the channel number you have set, based on
the quantity of control channels of the unit. That means changing the settings of one channel will affect
only the selected fixture.
In the case of the C19, which is 14/25 channels fixture. If you set, for example, the address in the 14
channel mode to channel 15, the device will use the channel 15 to 28 for control.
Universal DMX Control
This function allows you to use a universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique programs tailored to your individual
needs�
Auto run mode
In this mode, you can run internal program without a controller.
1� Press the MENU button until “RUN” is displayed, and press ENTER.
2� Press the UP or DOWN button to select “Auto 1” or “Auto 2”�
3� The unit will now run auto mode without a DMX controller.
Sound Mode
This mode allows either single unit or several units linked together, to run to the beat of the music.
1� Press the MENU button until “RUN” is displayed, and press ENTER.
2� Press the UP or DOWN button so that “Sound” is displayed�
3� The unit will now run to the beat of the music.
Master-Slave Operation
This function will allow you to link up to 16 units together and operate without a controller. In a Master-
Slave set up one unit will act as the controlling unit and the others will react to the controlling units
programs. Any unit can act as a Master or as a Slave.
1� Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear
of the units.
2� For the Master unit press the Run- Auto 1 / Auto 2�
3� For the slave units press the DMX address icon in the touch screen. Set the DMX address to 001.
4� The slave units will now follow the Master unit.

8Version 1.1hotion.com
C19 | LED aura moving head washEnglish
8
Control Menu Map
Default settings=bold print
Main Menu Level 1 Level 2 Level 3 Function
Address 001 - 512 DMX address setting
Run
DMX512
Run mode
Auto1
Auto2
Sound1
Sound2
DMX mode EXT 25 channel mode
STD 14 channel mode
Test
All
Test modeMotor
LED
Set
Disp�Setting
Shutoff time 02-60m Display shut off time
Flip display ON / OFF Display reverse
Key lock On / OFF Button lock
Disp flash ON / OFF Display flash
Pan Normal / Reverse Pan reverse
Tilt Normal / Reverse Tilt reverse
Language English / 中文 Language select
Time info
Power on xxxx(Hours)
System timeTtl Life Hrs xxxx(Hours)
Last Run Hrus xxxx(Hours)
Software V. Vx.xx Software version
Manual
Pan 000-255
Manual settings
Tilt 000-255
Speed 000-255
Functions 000-255
Red 000-255
Green 000-255
Blue 000-255
White 000-255
Clours 000-255
Zoom 000-255
Strobe 000-255
Dimmer 000-255
Reset All reset Yes/No Reset

9Version 1.1hotion.com
C19 | LED aura moving head washEnglish
9
DMX Protocol
STD
14 CH mode Function DMX value Function Control
1 Strobe
Beam electronic shutter effect
000 - 019 Shutter closed
020 - 024 Shutter open
025 - 064 Strobe 1: Synchronous strobe (fast to slow)
065 - 069 Shutter open
070 - 084 Strobe 2: On light pulse (fast to slow)
085 - 089 Shutter open
090 - 104 Strobe 3: Turn off the light pulse (fast to slow)
105 - 109 Shutter open
110 - 124 Strobe 4: Random strobe (fast to slow)
125 - 129 Shutter open
130 - 144 Strobe 5: Random on light pulse (fast to slow)
145 - 149 Shutter open
150 - 164 Strobe light 6: Pulses with the mechanism (fast to slow)
165 - 169 Shutter open
170 - 184 Stroboscopic 7: Burst pulse (fast to slow)
185 - 189 Shutter open
190 - 204 Strobe 8: Random burst (fast to slow)
205 - 209 Shutter open
210 - 224 Stroboscopic 9: Sine wave strobe (fast to slow)
225 - 229 Shutter open
230 - 244 Stroboscopic 10: Burst flash (fast to slow)
245 - 255 Shutter open
2 Master dimming 000 - 255 Master dimming from 0 - 100%
3 Zoom 000 - 255 Zoom from wide to narrow
4Pan 000 - 255 0 - 540 degrees
5Pan fine 000 - 255 Pan fine adjustment
6 Tilt 000 - 255 0 - 270 degrees
7 Tilt fine 000 - 255 Tilt fine adjustment
8 Fxiture control
Fixture control settings
000 - 009 No function
010 - 014 Reset entire fixture1
015 - 039 No function
040 - 044 PTSP = NORM2
045 - 049 PTSP = FAST2
050 - 054 PTSP = SLOW2
055 - 059 No function
060 - 064 Fan mode FULL2
065 - 069 No function
070 - 074 Fan mode REGULATED2
075 - 089 No function
090 - 094 Calibrated color output mode COLOR CALIB = ON3
095 - 099 No function
100 - 104 Raw color output mode COLOR CALIB = OFF3
105 - 109 No function
110 - 114 Fast dimming, speed of changes unrestricted2
115 - 119 No function
120 - 124 Smooth dimming, speed of changes restricted

10 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
10
125 - 249 slightly2
250 - 255 No function
Illuminate display
1. If DMX Reset is disabled in the menu, a reset command
can only be executed if channel 2 is set to 232 and channel
1 is set to zero. These values need to be held for 5 seconds
before 1feature is activated. Values must be "snapped to" to
function.
2. Menu override: setting unaffected by power off/on.
3. Value must be held for 3 seconds to activate. Setting
unaffected by power off/on.
9 Color wheel effect
Beam color wheel effect
000 - 009 Open
010 - 014 Color 1
015 - 019 Color 2
020 - 024 Color 3
025 - 029 Color 4
030 - 034 Color 5
035 - 039 Color 6
040 - 044 Color 7
045 - 049 Color 8
050 - 054 Color 9
055 - 059 Color 10
060 - 064 Color 11
065 - 069 Color 12
070 - 074 Color 13
075 - 079 Color 14
080 - 084 Color 15
085 - 089 Color 16
090 - 094 Color 17
095 - 099 Color 18
100 - 104 Color 19
105 - 109 Color 20
110 - 114 Color 21
115 - 119 Color 22
120 - 124 Color 23
125 - 129 Color 24
130 - 134 Color 25
135 - 139 Color 26
140 - 144 Color 27
145 - 149 Color 28
150 - 154 Color 29
155 - 159 Color 30
160 - 164 Color 31
165 - 169 Color 32
170 - 174 Color 33
175 - 179 Open
180 - 229 Color switching clockwise (fast to slow)
230 - 234 Open
Random color
235 - 239 Fast

11 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
11
240 - 244 Medium
245 - 249 Slow
250 - 255 Open
10 Red 000 - 255 Red dimming from 0 - 100%
11 Green 000 - 255 Green dimming from 0 - 100%
12 Blue 000 - 255 Blue dimming from 0 - 100%
13 White 000 - 255 White dimming from 0 - 100%
14 Color temperature 000 - 019 Color temperature disable
020 - 255 10000K to 2500K
25 CH mode Function DMX value Function Control
1 Strobe
Beam electronic shutter effect
000 - 019 Shutter closed
020 - 024 Shutter open
025 - 064 Strobe 1: Synchronous strobe (fast to slow)
065 - 069 Shutter open
070 - 084 Strobe 2: On light pulse (fast to slow)
085 - 089 Shutter open
090 - 104 Strobe 3: Turn off the light pulse (fast to slow)
105 - 109 Shutter open
110 - 124 Strobe 4: Random strobe (fast to slow)
125 - 129 Shutter open
130 - 144 Strobe 5: Random on light pulse (fast to slow)
145 - 149 Shutter open
150 - 164 Strobe light 6: Pulses with the mechanism (fast to slow)
165 - 169 Shutter open
170 - 184 Stroboscopic 7: Burst pulse (fast to slow)
185 - 189 Shutter open
190 - 204 Strobe 8: Random burst (fast to slow)
205 - 209 Shutter open
210 - 224 Stroboscopic 9: Sine wave strobe (fast to slow)
225 - 229 Shutter open
230 - 244 Stroboscopic 10: Burst flash (fast to slow)
245 - 255 Shutter open
2 Master dimming 000 - 255 Master dimming from 0 - 100%
3 Zoom 000 - 255 Zoom from wide to narrow
4Pan 000 - 255 0 - 540 degrees
5Pan fine 000 - 255 Pan fine adjustment
6 Tilt 000 - 255 0 - 270 degrees
7 Tilt fine 000 - 255 Tilt fine adjustment
8 Fxiture control
Fixture control settings
000 - 009 No function
010 - 014 Reset entire fixture1
015 - 039 No function
040 - 044 PTSP = NORM2
045 - 049 PTSP = FAST2
050 - 054 PTSP = SLOW2
055 - 059 No function
060 - 064 Fan mode FULL2
065 - 069 No function
070 - 074 Fan mode REGULATED2

12 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
12
075 - 089 No function
090 - 094 Calibrated color output mode COLOR CALIB = ON3
095 - 099 No function
100 - 104 Raw color output mode COLOR CALIB = OFF3
105 - 109 No function
110 - 114 Fast dimming, speed of changes unrestricted2
115 - 119 No function
120 - 124 Smooth dimming, speed of changes restricted
125 - 249 slightly2
250 - 255 No function
Illuminate display
1. If DMX Reset is disabled in the menu, a reset command
can only be executed if channel 2 is set to 232 and channel
1 is set to zero. These values need to be held for 5 seconds
before 1feature is activated. Values must be "snapped to" to
function.
2. Menu override: setting unaffected by power off/on.
3. Value must be held for 3 seconds to activate. Setting
unaffected by power off/on.
9 Color wheel effect
Beam color wheel effect
000 - 009 Open
010 - 014 Color 1
015 - 019 Color 2
020 - 024 Color 3
025 - 029 Color 4
030 - 034 Color 5
035 - 039 Color 6
040 - 044 Color 7
045 - 049 Color 8
050 - 054 Color 9
055 - 059 Color 10
060 - 064 Color 11
065 - 069 Color 12
070 - 074 Color 13
075 - 079 Color 14
080 - 084 Color 15
085 - 089 Color 16
090 - 094 Color 17
095 - 099 Color 18
100 - 104 Color 19
105 - 109 Color 20
110 - 114 Color 21
115 - 119 Color 22
120 - 124 Color 23
125 - 129 Color 24
130 - 134 Color 25
135 - 139 Color 26
140 - 144 Color 27
145 - 149 Color 28
150 - 154 Color 29
155 - 159 Color 30

13 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
13
160 - 164 Color 31
165 - 169 Color 32
170 - 174 Color 33
175 - 179 Open
180 - 229 Color switching clockwise (fast to slow)
230 - 234 Open
Random color
235 - 239 Fast
240 - 244 Medium
245 - 249 Slow
250 - 255 Open
10 Red 000 - 255 Red dimming from 0 - 100%
11 Green 000 - 255 Green dimming from 0 - 100%
12 Blue 000 - 255 Blue dimming from 0 - 100%
13 White 000 - 255 White dimming from 0 - 100%
14 Color temperature 000 - 019 Color temperature disable
020 - 255 10000K to 2500K
15 FX1 select
FX1 select
Pre-programmed effect 1 selection
000 - 009 Empty
010 - 012 Dimmer -Sync - Strobe is not synchronized
013 - 015 Strobe-sync
016 - 018 Dimmer + strobe - synchronous
019 - 021 Halo-color-sync
022 - 024 Aura-All-Sync
025 - 099 obligate
100 - 102 Circle color 1-offset dynamic effect
103 - 105 Circle color 2-offset dynamic effect
106 - 108 Circle color 3-offset dynamic effect
109 - 111 Circle color 4-offset dynamic effect
112 - 114 Circle color 5-offset dynamic effect
115 - 117 Circle color 6-offset dynamic effect
118 - 120 Circle color 7-offset dynamic effect
121 - 123 Circle color 8-offset dynamic effect
124 - 126 Circle color 9-offset dynamic effect
127 - 129 Circle color 10-offset dynamic effect
130 - 132 Circle color 11-offset dynamic effect
133 - 135 Circle color 12-offset dynamic effect
136 - 138 Circle color 13-offset dynamic effect
139 - 141 Circle color 14-offset dynamic effect
142 - 159 obligate
160 - 162 Color-Scale-Gradient-Input
163 - 165 Color-Scale-Gradient-Scale
166 - 168 Color-Scale-Fade-Zoom
169 - 255 obligate
16 Built-in effect 1
speed 000 - 255
FX1 adjust, sync speed adjust
Zero to maximum
• If no sync set on channel 19, adjusts FX1
• If sync set on channel 19, adjusts synchronized FX1+FX2
speed

14 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
14
17 Built-in effects 2
selection
FX2 adjust
Zero to maximum
• If no sync set on channel 19, adjusts FX2
• If sync set on channel 19, has no effect
000 - 009 Empty
010 - 012 Dimmer -Sync - Strobe is not synchronized
013 - 015 Strobe-sync
016 - 018 Dimmer + strobe - synchronous
019 - 021 Halo-color-sync
022 - 024 Aura-All-Sync
025 - 099 obligate
100 - 102 Circle color 1-offset dynamic effect
103 - 105 Circle color 2-offset dynamic effect
106 - 108 Circle color 3-offset dynamic effect
109 - 111 Circle color 4-offset dynamic effect
112 - 114 Circle color 5-offset dynamic effect
115 - 117 Circle color 6-offset dynamic effect
118 - 120 Circle color 7-offset dynamic effect
121 - 123 Circle color 8-offset dynamic effect
124 - 126 Circle color 9-offset dynamic effect
127 - 129 Circle color 10-offset dynamic effect
130 - 132 Circle color 11-offset dynamic effect
133 - 135 Circle color 12-offset dynamic effect
136 - 138 Circle color 13-offset dynamic effect
139 - 141 Circle color 14-offset dynamic effect
142 - 159 obligate
160 - 162 Color-Scale-Gradient-Input
163 - 165 Color-Scale-Gradient-Scale
166 - 168 Color-Scale-Fade-Zoom
169 - 255 obligate
18 Built-in effect 2
speed 000 - 255 Built-in program effect 2 speed adjustment
19 Built-in program
switching
000 - 169 Built-in Program Effects 1 Built-in Program Effects 1 Speed
Effective
170 - 255 Built-in Effects 2 Built-in Program Effects 2 Speed Effective
20 Aura strobe effect
000 - 019 Shutter closed
020 - 024 Shutter open
025 - 064 Strobe 1: Synchronous strobe (fast to slow).
065 - 069 Shutter open
070 - 084 Strobe 2: On light pulse (fast to slow).
085 - 089 Shutter open
090 - 104 Strobe 3: Turn off the light pulse (fast to slow).
105 - 109 Shutter open
110 - 124 Strobe 4: Random strobe (fast to slow).
125 - 129 Shutter open
130 - 144 Strobe 5: Random on light pulse (fast to slow).
145 - 149 Shutter open
150 - 164 Strobe light 6: Pulses with the mechanism (fast to slow).
165 - 169 Shutter open
170 - 184 Stroboscopic 7: Burst pulse (fast to slow).
185 - 189 Shutter open
190 - 204 Strobe 8: Random burst (fast to slow).

15 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
15
205 - 209 Shutter open
210 - 224 Stroboscopic 9: Sine wave strobe (fast to slow).
225 - 229 Shutter open
230 - 244 Stroboscopic 10: Burst flash (fast to slow).
245 - 255 Shutter open
21 Aura dimming 000 - 255 Aura dimming from 0 - 100%
22 Aura color effect
000 - 009 Open
010 - 014 Color 1
015 - 019 Color 2
020 - 024 Color 3
025 - 029 Color 4
030 - 034 Color 5
035 - 039 Color 6
040 - 044 Color 7
045 - 049 Color 8
050 - 054 Color 9
055 - 059 Color 10
060 - 064 Color 11
065 - 069 Color 12
070 - 074 Color 13
075 - 079 Color 14
080 - 084 Color 15
085 - 089 Color 16
090 - 094 Color 17
095 - 099 Color 18
100 - 104 Color 19
105 - 109 Color 20
110 - 114 Color 21
115 - 119 Color 22
120 - 124 Color 23
125 - 129 Color 24
130 - 134 Color 25
135 - 139 Color 26
140 - 144 Color 27
145 - 149 Color 28
150 - 154 Color 29
155 - 159 Color 30
160 - 164 Color 31
165 - 169 Color 32
170 - 174 Color 33
175 - 179 Open
180 - 229 Color switching efect (fast to slow)
230 - 255 Open
23 Aura red 000 - 255 Aura red dimming from dark to light Fill light
24 Aura green 000 - 255 Aura green dimming from dark to light Fill light
25 Aura blue 000 - 255 Aura blue dimming from dark to light Fill light
Fixture Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should
be carried out periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning

16 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
16
on a monthly basis. Periodic cleaning will ensure longevity, and crisp output.
To clean the fixture:
1� Disconnect the fixture from power and allow it to cool for at least 10 minutes.
2� Vacuum or gently blow away dust and loose particles from the outside of the fixture with low-
pressure compressed air.
3� Clean the surfaces by wiping gently with a soft, clean lint-free cloth moistened with a weak detergent
solution. Do not rub glass surfaces hard: lift particles off with a soft repeated press. Dry with a soft,
clean, lint-free cloth or low-pressure compressed air. Remove stuck particles with an unscented
tissue or cotton swab moistened with glass cleaner or distilled water.
4� Check that the fixture is dry before reapplying power.
Fuse Replacement
This fuse is located in a fuseholder next to the MAINS OUT socket on the connections panel.
To replace a fuse:
1� Disconnect the fixture from power and allow it to cool for at least 10 minutes.
2� Unscrew the cap of the fuseholder and remove the fuse. Replace with a fuse of the same size and
rating only�
3� Reinstall the fuseholder cap before reapplying power.
Troubleshooting
Listed below are a few common problems that you may encounter, with solutions.
The fixture does not work, no light
• Check the connection of power and main fuse. Be sure the external fuse has not blown.
• Measure the mains voltage on the main connector.
No response to the sound
• Make sure the fixture does not receive DMX signal.
• Low frequencies (bass) should cause the unit to react to sound.Tapping on the microphone, quiet or
high pitched sounds may not activate the unit.
• Check the sound sensitivity level. Make sure it is not set to a low sensitivity level.

17 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
17
Specifications
Model C19
Power supply: AC100 - 240V, 50/60Hz
Light source: 19 x 15W RGBW LED
Power consumption: 230Watt max.
Color temperature: Adjustable
Pan: 540°
Tilt: 270°
Zoom: 8° - 50°
Power connection: PowerCON in & out
Signal connection: 3-pin XLR in & out
DMX channels: 14/25
Control mode: DMX, Auto program, Sound, Master-slave
Housing: Colour black, Plastic
Size: 300 x 200 x 380mm(11.8 x 7.9 x 14.9in)
N.W.: 8.3kg(18.3lb)
G.W.: 9.5kg(20.9lb)
Enviroment: IP20
Please note: All information is subject to change without prior notice� 24�09�2022

18 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
18

19 Version 1.1hotion.com
C19 | LED aura moving head washEnglish
19
Table of contents
Other Ovation Lighting Equipment manuals

Ovation
Ovation PIONEER 200C ZOOM User manual

Ovation
Ovation Min-E-10WW User manual

Ovation
Ovation EXT 1218 User manual

Ovation
Ovation E-3 IP User manual

Ovation
Ovation Event 200T User manual

Ovation
Ovation PIONEER 100C ZOOM User manual

Ovation
Ovation SPACE MINI PROFILE 40Z User manual

Ovation
Ovation Event 100T User manual

Ovation
Ovation Solar Panel 150T User manual

Ovation
Ovation CTC 300 FRESNEL User manual