Overhead door car2u Installation manual

©2013 Overhead Door Corporation.
Car2U®System Programming for
Overhead Door®Garage Door Openers
Setting the Car2U to Factory Default settings
The default setting for the Car2U system is:
•Button 1= Overhead Door®manufactured openers
•Button 2= LiftMaster®manufactured openers
•Button 3= Wayne Dalton®manufactured openers
1. Press and hold buttons 1 and 3 for twenty seconds or until all three
LED’s begin to flash.
2. Release both buttons. The Car2U system is now set to the Factory
Default settings.
123
Changing a button to Overhead Door
1. Press and hold buttons 1 and 3 for one second and release– all
three LED’s will light solid RED.
2. Press and Hold the button (2 or 3) you want to change to Overhead
Door – the corresponding LED will flash. While continuing to hold the
button you want to change, Press and release button 1. Press and
release button 1 again.
3. Release the button (2 or 3) you were holding in Step 2 and wait for
the LED to stop flashing. This button is now set for Overhead Door.
NOTE: Repeat this procedure for the remaining button to change to
Overhead Door if so desired.
1

©2013 Overhead Door Corporation.
Car2U®System Programming for
Overhead Door®Garage Door Openers
Programming Car2U to an Overhead Door®garage door opener:
1. Press and hold the program button until the round blue LED
is on – release the button.
The long LED will flash purple.
2. Press the desired Car2U button for one second and release. Press
that same button again for one second and release. The round
LED and long LED will both turn blue and then turn off.
3. Pressing the Car2U button again will cause the garage door to
move.
NOTE: If you cannot find your program button on the power head, see
the user manual or visit www.overheaddoor.com for additional
assistance.
PRGM
Odyssey®1000, Destiny® 1200,
Odyssey ® 1200, Destiny ® 1500
Manufactured after November 2011
2

Car2U®System Programming for
Overhead Door®Garage Door Openers
Programming Car2U to an Overhead Door®garage door opener:
1. Press and hold the program button until the round blue LED
and the long blue LED are on – release the button. The round
blue LED will be on.
2. Press the program button once the long purple LED will begin
flashing.
3. Press the desired Car2U button for one second and release. Press
the same button again and release. The long LED will flash blue
and then turn off.
4. Pressing the Car2U button again will cause the garage door to
move.
NOTE: If you cannot find your program button on the power head, see
the user manual or visit www.overheaddoor.com for additional
assistance.
PRGM
Odyssey®1000, Destiny® 1200,
Odyssey ® 1200, Destiny ® 1500
Manufactured before November 2011
PRGM
3
©2013 Overhead Door Corporation.

Car2U®System Programming for
Overhead Door®Garage Door Openers
Programming Car2U to an Overhead Door®garage door opener:
1. Press and hold the program button until the round blue LED
and the long blue LED are on – release the button. The round
blue LED will be on.
2. Press the program button once - the long purple LED will begin
flashing.
3. Press a previously learned CodeDodger®2
transmitter button from model O3T (pictured right)
one time. Both the long and round
LEDs flash purple.
4. Press the desired Car2U button for one second and release. Both
the long and round LEDs go solid purple.
5. Press the desired Car2U button (again) for one second and release.
Both the long and round LEDs change from solid purple to solid blue
and then go out.
6. Pressing the Car2U button again will cause the garage door to
move.
NOTE: If you cannot find your program button on the power head, see
the user manual or visit www.overheaddoor.com for additional
assistance.
PRGM
Odyssey®1000, Destiny® 1200,
Odyssey ® 1200, Destiny ® 1500
Manufactured before July 2011 Learn Window
PRGM
4
©2013 Overhead Door Corporation.

Car2U®System Programming for older
Overhead Door®Garage Door Openers
Programming Car2U to an Overhead Door®garage door opener:
1. Press and release the learn code button - the red LED will begin to
blink.
2. Press the desired Car2U button one time. The red LED will stop
blinking and stay on.
3. Press the desired Car2U button one more time. The red LED will go
out.
4. Pressing the Car2U button again will cause the garage door to
move.
NOTE: If you cannot find your program button on the power head, see
the user manual or visit www.overheaddoor.com for additional
assistance.
If your learn button looks like this:
5
©2013 Overhead Door Corporation.

Car2U®System Programming for
Overhead Door®Garage Door Openers
Programming Car2U to an Overhead Door®garage door opener:
1. Press and release the learn code button the red LED will begin
to blink.
2. Press the desired Car2U button one time. The red LED will stop
blinking and stay on.
3. Press the desired Car2U button one more time. The red LED will go
out.
4. Pressing the Car2U button again will cause the garage door to
move.
NOTE: If you cannot find your program button on the power head, see
the user manual or visit www.overheaddoor.com for additional
assistance.
Standard Drive®600, Legacy®800
CODE
6
©2013 Overhead Door Corporation.