Overland Tandberg NEOxl 40 User manual

*10400850001*
10400850-001 ©2018 Overland Storage, Inc. Page 1 of 5
NEOxl®40 Tape Library
Add-on Expansion Module Instructions
This document describes how to add an optional Expansion
Module to a NEOxl 40 (3U) tape library from Overland
Storage.
WARNING: To reduce the risk of electric shock or damage to
equipment, always remove any power cords while working with
the library.
WARNUNG: Um das Risiko eines elektrischen Schlags oder
Schäden am Gerät zu vermeiden, ziehen Sie stets den
Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT: Pour réduire le risque de choc électrique
ou endommagement de l'équipement, retirez toujours les
cordons électriques en travaillant avec l'appareil.
CAUTION: While working with the library, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
Special Handling Notice
Each NEOxl 40 Expansion Module weighs more than 44
lbs (20 kg) without drives or tapes and more than 77 lbs
(35 kg) with three tape drives and 40 tapes.
Before moving or lifting the Expansion Module, remove
the tape magazines and drives to reduce the weight.
Overview
To install an Expansion Module, the main steps include:
1. After determining the installation location, if necessary,
transfer the library top or bottom cover to the new
Expansion Module.
2. Make space in the rack and install the rack rails.
3. If applicable, install the power supplies.
4. If applicable, install the DC-DC drive power board.
5. Install the Expansion Module in the rack and align the
module with the library.
6. If applicable, install the tape drives.
7. Attach the cables and cords.
8. Install the tape magazines and verify the installation.
You will need a small flat head or Torx screwdriver and a #2
Phillips screwdriver.
Prepare the Library
Power Off Library
If still running, power off the library from the Base Module
front panel by pressing and holding down the power button for
three (3) seconds.
NOTE: If the library does not perform a soft shutdown, press and
hold the power button for 10 seconds.
Verify that the Robotic Assembly is in its parked position and
that all host processes are idle.

NEO Add-on Expansion Module Instructions
10400850-001 ©2018 Overland Storage, Inc. Page 2 of 5
Determine Installation Location
If library expansion was planned and the Base Module is in the
middle of the rack, there should be space for up to three
Expansion Modules above and below the Base Module.
When Expansion Modules are already in place, to eliminate the
steps needed to move covers, install the new rack rails in the
space above or below a current Expansion Module. Move the
existing Expansion Module onto the new rails and install the
new Expansion Module in its old space.
See Chapter 1, “Supported Configurations,” in the NEOxl 40
Tape Library Administrator’s Guide for additional details.
Install the Expansion Module
Install the Rack Rails
1. Determine the location in your rack for your Expansion
Module to be installed and, using a pencil, mark the
location on each vertical rail in your rack.
NOTE: The modules require 3U (5.25 in.) of rack space each.
2. On the front of the rack, mount the left and right adapter
blocks with the lower fixed nut in the middle hole of the
bottom 1U space reserved for the module.
3. Secure the adapters with a screw through the front into
one of the middle holes.
4. Mount the rear adapters making sure they are level with
the front ones.
5. Mount the LH Rackmount rail to the left adapter blocks
with the tray flange parallel to the floor and facing
inward.
6. Mount the RH Rackmount rail to the right adapter
blocks.
Move Cover to the New Module
IMPORTANT: When replacing an Expansion Module in either
the top or bottom position, you must move the cover from the
old Expansion Module to the new one.
To move a top cover:
1. At the old Expansion Module, unlock the top cover by
pushing two small screwdrivers down and inward in
both slots.
2. Lift the top cover front edge by about 4.75 in. (12cm) and
pull the cover gently forward to disengage from the pivot
point at the module center.
3. At the new Expansion Module, with the cover at the same
angle, reengage the rear of the cover at the pivot point.
4. Lower the front of the top cover until the latches engage
on both sides.
Install New
Move Up
New Rail
Old Rail
New Rail
Old Rail
Unit Here
Reserve 3U (5.25 in.)
For Each Module
Adapter
Block
LH Rail
RH Rail

NEO Add-on Expansion Module Instructions
10400850-001 ©2018 Overland Storage, Inc. Page 3 of 5
To move a bottom cover:
1. Place both Expansion Modules upside-down.
2. At the old Expansion Module, insert a small flathead or
Torx screwdriver into the release hole and slide it about
1/4 in. (4mm) sidewards to unlock the spring loaded lock.
3. Raise the cover front end by about 4 in. (10cm) and
gently pull it forward to disengage from the pivot point at
module center and remove.
4. At the new Expansion Module, with the cover at the same
angle, reengage the rear of the cover at the pivot point.
5. Lower the front of the cover until the latch engages.
Install Optional Power Supplies
If the Expansion Module comes with power supplies:
1. Remove the appropriate power supply covers.
The top cover for the primary power supply and, if there is
a redundant power supply, also the bottom cover.
2. While supporting the bottom, position the power supply
onto the alignment rails in the open bay.
3. Slide the power supply into the module until it is flush
with the back panel of the module.
4. Tighten the thumbscrews with your fingers to secure it.
5. If necessary, repeat these steps for a redundant power
supply.
Install Optional DC-DC Board
If the Expansion Module comes with a DC-DC drive power
board for tape drives:
1. Loosen the two blue captive thumbscrews on the
controller and slowly remove it from the Expansion
Module, setting it aside on a secure ESD surface.
2. Position the drive power board onto the alignment rails
inside the controller compartment.
3. Slide the drive power board in until seated firmly.
4. Push the board latch up until it snaps into place.
5. Position the controller on the alignment rails and slide it
back in until it is flush with the back panel of the module.
6. Tighten the thumbscrews with your fingers to secure it
to the module.
Primary
Redundant

NEO Add-on Expansion Module Instructions
10400850-001 ©2018 Overland Storage, Inc. Page 4 of 5
Insert the Module in the Rack
WARNING: To avoid injury, it is recommended that a
mechanical lifter (or at least two people) be used for rack
installation or removal. Use care during rack installation or
removal to avoid accidentally tilting or tipping the rack,
causing damage or personal injury.
WARNUNG: Um Verletzungen zu vermeiden, empfehlen wir zur
Rack-Installation oder -Deinstallation die Nutzung einer
mechanischen Hebehilfe (oder mindestens zwei Personen).
Seien Sie vorsichtig bei der Rack-Installation oder -Entnahme,
um ein versehentliches Kippen des Racks zu vermeiden und
das Rack nicht zu beschädigen bzw. sich selbst zu verletzen.
AVERTISSEMENT: Afin d’éviter des blessures pendant
l’installation, il est recommande d’utiliser un monte-charge (ou
au moins deux personnes) pour élever ou aligner l’module.
Faites attention lorsque vous insérez ou retirez l’module d’un
support, pour empêcher le déversement accidentel de la
crémaillère causant des dommages et des blessures.
1. Position the module in front, aligned with the rails.
2. Slide the module onto the rail flanges and into the rack.
3. Tighten the recessed screws only one turn to hold it.
Aligning and Connecting the Module
Aligning the Expansion Module with the library ensures that
the robot can move freely between the modules.
NOTE: The library will not operate unless the alignment
mechanism is in the locked position (except the bottom module).
1. At the back of the library, using the alignment lock
lever, align and lock the new Expansion Module to the
modules to which it connects.
If you encounter resistance, adjust the upper module so
that the alignment mechanism pin moves into the mating
hole in the lower module.
2. Verify that, for the lowest module in the library, its
alignment mechanism is in the unlocked position.
3. From the front of the library, tighten the Phillips screws
on both the Expansion Module and the adjacent modules
to secure them all to the rack.
Install Optional Tape Drives
If the Expansion Module comes with tape drives:
1. Remove the appropriate tape drive covers.
Start with the bottom cover and work your way up.
2. Holding a tape drive by the handle and supporting it
from the bottom, position it on the alignment rails.
3. Slowly slide the tape drive into the drive bay until it is
flush with the back of the library.
4. Finger-tighten the blue captive thumbscrews to secure
the tape drive.
5. Repeat Steps 2–4 for any additional tape drives.
Recessed Screws
Alignment Locks

http://support.overlandstorage.com
You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using
the information found on the Contact Us page on our web site.
NEO Add-on Expansion Module Instructions
10400850-001 ©2018 Overland Storage, Inc. Page 5 of 5
Attach Cables
Reconnect all cables and cords:
1. Connect the expansion interconnect cables (1) from the
Expansion Module to any adjacent modules.
2. If tape drives are installed, connect the SAS/FC cables
(2) to the appropriate ports on the drives.
3. If power supplies are installed, plug in their AC power
cords (3).
Load Tape Cartridges
If desired, cartridges can be added to the magazines before
using the Expansion Module.
1. Insert a small flat head screwdriver or Torx driver into the
appropriate magazine release hole and gently push the
tab in.
IMPORTANT: Do not continue to exert force once you
encounter resistance. Doing so can damage the device.
2. Using the magazine access handle and supporting it
underneath, pull the magazine out of the library and place
it on a secure surface.
3. Load the cartridges into the magazine.
4. Using the magazine access handle and supporting it
underneath, position the magazine on the alignment rails
and slide the magazine back into the module.
5. Repeat Steps 1–4 for the other magazine.
Verifying the Installation and Configuration
Power on the library and check the following:
•Verify that the library powers on and initializes correctly,
and that the status is Ready.
•From the OCP or RMI, verify that the new Expansion
Module is visible.
•Check the library configuration settings related to the
additional storage slots, mailslots, and tape drives.
Update if necessary.
The Expansion Module operates using the existing library
firmware. It is recommended that you always update the
library to the latest firmware version. You can update
firmware from the RMI or the OCP
Maintenance > Library
Firmware Upgrade
screen.
3
21