Ozito ZLCG-112 User manual

1
CHARGER SAFETY WARNINGS
ELECTRICAL SAFETY
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landll and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
DESCRIPTION OF SYMBOLS
ZLCG-112
FAST CHARGER
12V Lithium Ion
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 100-240V AC 50/60Hz
Output: 15V DC, 1700mA
Charge Times: 1hr (1.5Ah Battery)
ozito.com.au
1 2 3
1 Charging Adaptor
2 Charging Cradle
3 Charge Indication Lights
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR
YOUR BATTERY CHARGER.
1. Before using the charger read all instructions and cautionary markings on the charger,
battery pack and the product using the battery pack.
2. This charger is not intended for any uses other than charging rechargeable batteries. Any
other use may result in risk of re, electric shock or electrocution.
3. Do not place any object on top of the charger or place the charger on a soft surface that
may result in excessive internal heat. Place the charger in a position away from any heat
source.
4. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the
cord when disconnecting the charger.
5. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
6. An extension cord should not be used unless absolutely necessary. Use of an improper
extension cord could result in the risk of re, electric shock or electrocution.
7. Do not operate the charger if it has received a sharp blow, been dropped or otherwise
damaged in any way. Have it checked by an electrician or power tool repairer.
8. Do not disassemble charger. Take it to an electrician or power tool repairer when
service or repair is required. Incorrect reassembly may result in a risk of electric shock,
electrocution or re.
9. To reduce risk of electric shock, unplug the charger from the outlet before attempting any
cleaning. Removing the battery pack will not reduce this risk.
10. Never attempt to connect 2 chargers together.
11. DO NOT store or use the tool and battery pack in locations where the temperature may reach
or exceed 40ºC (such as inside sheds or metal buildings in summer).
12. The charger is designed to operate on standard household electrical power (240 volts).
Do not attempt to use it on any other voltage!
13. The battery pack is not fully charged out of the carton. First read the safety instructions
and then follow the charging notes and procedures.
14. The longest life and best performance can be obtained if the battery pack is charged
when the air temperature is between 18 - 24ºC. Do not charge the battery pack in an air
temperature below 10ºC or above 40ºC. This is important and will prevent damage to the
battery pack.
15. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out.
The battery can explode in a re.
16. Never attempt to open the battery pack for any reason. If the plastic housing of the battery
pack breaks or cracks, immediately discontinue use and do not recharge.
17. During charging, the battery must be placed in a well ventilated area.
WARNING! When using mains-powered tools, basic safety precautions,
including the following, should always be followed to reduce risk of re, electric
shock, personal injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an
emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that the power
supply corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New
Zealand.
This tool is double insulated therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in
order to avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating
this tool. The insulation system is for added protection against injury resulting from a possible
electrical insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use,
inspect the extension lead for signs of damage, wear and ageing. Replace the extension lead if
damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an
extension lead not suitable for the power input of the tool or which is damaged or defective may
result in a risk of re and electric shock.
Warning Read instruction manual
mA Milliamperes
Polarity
Thermal cut-out protection
Transformer Energy
Rating (MEPS)
Double insulated
A Amps
Indoor use only
Regulator compliance
mark (RCM)
VVolts Hz Hertz
ac/~ Alternating current WWatts
Direct current
dc/ Ah Amp hour
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.

1
• Disconnect the charger from power source before cleaning.
• Keep the charger in a dry place out of reach of children.
• If the enclosure of the charger requires cleaning, do not use
solvents. Use a dry, soft cloth only to wipe down the surface. Never
let any liquid get inside the charger; never immerse any part of the
drill into a charger.
• There are no other parts inside the charger which require
maintenance. Do not take the charger apart. If the charger is
damaged, contact your supplier or the manufacturer.
ZLCG-112
Only use this charger with Ozito Home 12Volt batteries.
1. CHARGING A BATTERY 2. MAINTENANCE
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE
WITH YOUR BUNNINGS REGISTER RECEIPT.
PRIOR TO RETURNING YOUR PRODUCT
FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
1 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 12 months from the
original date of purchase and is intended for DIY (Do It Yourself) use
only. If a product is defective it will be replaced in accordance with the
terms of this warranty. Warranty excludes consumable parts.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other than that
specified on the tool.
• If the tool shows signs of damage or defects caused by or
resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction
manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You
are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount
to a major failure.
Generally you will be responsible for all costs associated with a claim
under this warranty, however, where you have suffered any additional
direct loss as a result of a defective product you may be able to claim
such expenses by contacting our customer service helpline above.
1 Connect the charging adaptor to a
mains power outlet.
The red led light on the back of the
plug will illuminate red indicating it
is connected correctly.
2 With the battery sitting on a at
surface, align the raised ribs on
the battery with the recess in the
charging cradle and slide onto the
battery ensuring a rm connection.
3 The red LED on the charging
cradle will illuminate signifying that
the battery is charging.
4 Once the green LED on the
charging cradle illuminates, the
battery is charged and can be
removed from the charging cradle
using the battery release button.
Note: The battery will not develop a memory, it does not have to be
fully discharged before recharging.
Charger LED Indicator
LED Indicator Situation
RED (Illuminated) Battery is charging (low charge)
GREEN (Illuminated) Battery is fully charged
RED & GREEN (Flashing) Battery or Charger fault
RED & GREEN (Illuminated) Battery pack is too hot or too cold
(remove battery from charger and
store at room temperature 20ºC. Insert
battery again when at correct charging
temperature). If this happens again, the
battery is defective and needs to be
replaced.
WARNING! THE POWER SUPPLY FOR THIS CHARGER IS
RECOMMENDED FOR USE WITH A RESIDUAL CURRENT
DEVICE (RATED AT 30mA OR LESS).