Ozito CMX-125U User manual

CEMENT
MIXER
550W 125L
SPECIFICATIONS
Motor: 550W
No Load Speed 2950/min
Drum Speed: 34/min
Gross Drum Volume: 125L (4.41 cu ft)
Unmixed Dry Volume: 100L (3.53 cu ft)
Mixed Wet Volume: 91L (3.21 cu ft)
Drum Mouth: Ø375mm (14 ¾”)
IP Rating: IP44
Weight: 48kg
CMX-125U
WHAT’S IN THE BOX
Cement Mixer
Assembly Fasteners
WARRANTY
0616
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the customer
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectication of said
defects on the product or the replacement of the product, whichever we
prefer.
Please note that our devices are not designed for use in commercial, trade
or professional applications. A guarantee contract will not be created if the
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Warranty
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts tted. This also applies if an on-site service is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR
REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk
ozito-diy.co.uk
ORIGINAL INSTRUCTIONS

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
KNOW YOUR PRODUCT
1. FRAME ASSEMBLY
1 Tipping Handle
2 Drum Assembly
3 On/Off Switch
4 Motor and Motor Housing
Assembly
5 Locking Plate
6 Frame Assembly
7 Wheels
CEMENT MIXER
8 Assembly Fasteners
9 Lower Drum
10 Locking Plate
11 Tipping Handle
12 Mixing Blades
13 Rubber Gasket
14 Upper Drum
15 Support Leg
16 Motor and Motor Housing
17 Wheels
18 Frame
19 Wheel Frame
ASSEMBLY COMPONENTS
SETUP & PREPARATION
1
2
3
4
5
6
7
14
15
16
17
18
8
9
10
11
12
13
WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING ASSEMBLY.
Tools Required (Not Supplied)
2. First place 2 large washers
then wheel, followed by
another 3 large washer onto
axle of the wheel frame,
secure the assembly with split
pin. Repeat assembly for other
wheel.
4. Insert the M8x65 hex bolts
with washer through the 2
holes from one side and the
M8x55 hex bolt with washer
through the end hole of the
support leg and secure with
nut.
2 x
3 x
1. Use assembly
fasteners bag
3. Align and insert
wheel assembly and
support leg into the
frame.
Spanners 13, 14 & 17mm.
Note: It is recommended that two people assemble the cement mixer.
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
A
B
C
D
E
F
G
A
19
5. Insert the M8x65 hex bolts
with washer through the 2
holes from one side and the
M8x55 hex bolt with washer
through the end hole of the
wheel assembly and secure
with nut.
6. Tighten bolts and nuts assembled in above steps 4 & 5 with a 13
and 14mm spanners (not supplied).

3. MIXING BLADE ASSEMBLY2. DRUM ASSEMBLY
2. With the help of a second
person, carefully set the lower
drum onto the side supports
of the frame assembly. Ensure
the large diameter shaft is
at the support leg end of the
stand
6. Position the upper drum over
the rim of the lower drum.
Ensure that all the mounting
holes align as well as the
arrows on either side of the
rim.
4. Align the Rubber Gasket with
the holes and screw heads on
the lower drum.
Note: Ensure the Rubber Gasket
is not twisted and at on the lower
drum.
Shaft
1. Use assembly
fasteners bag
5. Use assembly
fasteners bag
3. Secure the lower drum
to the frame assembly by
inserting the M8x55 bolts
with washers into the side
supports and secure with
the nuts. Tighten with 13
& 14mm spanners (not
supplied).
7. Insert the M8x20 bolts, spring
washers and at washers into
each of the mounting holes in
the rim. Secure each bolt with
14mm spanner (not supplied).
2. Insert 2 M8x20 bolts and washers into the upper and lower drum
from the outside. Place the rubber washer, thin washer onto the bolt
followed by the end of the mixing blade and secure with thin washer
and nut.
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
Bolt
Thin Washer
Nut
Rubber Washer
Washer
B
C
D
Hole
Screw Head
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
1. Use assembly
fasteners bag
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
3. Repeat step 2 for the second mixing blade. Then ensure both ends
of the mixing blades are tight.
Note:Position the mixing blade inside the drum assembly with the
pointed end facing downward.

4. LOCKING PLATE ASSEMBLY 5. TIPPING HANDLE & MOTOR ASSEMBLY
2. Slide the locking plate over
the large diameter shaft at
the support leg end of the
frame assembly. Ensure
the plate is correctly
aligned with the bearing
bracket and clear of the
circlip.
3. Insert the M10x70
bolt with washer and
secure with washer
and nut. Tighten with
17mm spanner (not
supplied).
Note: Ensure the tipping
handle easily pivots
on the large shaft so
that the locating pins
can be engaged and
disengaged.
2. Insert the M8x16 bolt and spring into the tube of the tipping handle.
Engage the locating pins into the locking plate and use this as a
lever to compress the spring against the large shaft.
1. Use assembly
fasteners bag
1. Use assembly
fasteners bag
4. Use assembly
fasteners bag
3. Insert the 2 M8x30 hex bolts,
spring washers and washers.
Secure with nut from rear of
bearing bracket. Tighten with
13 & 14mm spanners (not
supplied).
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
Bolt
Spring
M8 x 25
M8 x 20
EF
G
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
2
4
2
2
2
6
4
M8 55
M8 65
M8 60
M8 20
M8 20
M8 30
M8 20
1
M10 70
2
10
2
4
M8 16 1
1
2
M8 25
4
4
4
8
5. Slide the motor and
motor housing over
the pinion shaft lining
up the key ways.
Secure the motor and
motor housing to the
frame with the bolts,
spring washers and
washers. Tighten with
14mm spanner (not
supplied).

6. PLACEMENT 7. CONTROLS
The product may only be placed on a at surface. To provide added
stability screw the product to a concrete oor with the proper xation
materials including bolts, screws and washers.
1. Disengage the locating pins
by pulling out on the control
handle away from the locking
plate to allow the drum to
rotate.
The drum can be set
at different position to
cater for mixing mortar
and concrete, emptying
or storing.
The Support Leg has two
mounting holes that can be used
to ensure sufcient stability. Use
two screws or bolts (not included,
recommended size M10 ) to secure.
ON
OFF
Mortar
Concrete
Unload
Storage
ON
OFF
Mortar
Concrete
Unload
Storage
3. Engage the control handle
locating pins to secure the
position.
Drip Loop
To avoid the possibility of the appliance plug or power point getting wet,
the user should arrange a “drip loop” in the cord connecting the cement
mixer to a wall mounted power point.
The “drip loop” is the part of the cord that sits below the level of the
power point (or the connector if an extension cord is used). It prevents
water travelling along the cord and coming in contact with the power
point.
CMX-125U
WARNING! DO NOT PLACE ANY MATERIAL UNDER THE
PRODUCT TO ADJUST THE HEIGHT OR TO ATTEMPT
TO IMPROVE ITS STABILITY! IF THE PRODUCT IS ON
AN ANGLE AND/OR WOBBLY, MOVE IT TO A DIFFERENT
LOCATION. NEVER OPERATE THE PRODUCT ON SOFT
SURFACES SUCH AS A LAWN OR GRAVEL SINCE IT
COULD SINK OR TIP OVER DURING OPERATION!
CAUTION! TO REDUCE THE RISK OF ELECTRICAL
SHOCK, THE USE OF A RESIDUAL CURRENT DEVICE
(RATED 30mA OR LESS) IS RECOMMENDED.
OPERATION
Setting the Operating Position
2. Rotate the drum to the desired
position by aligning the
locating pin with two of the
holes in the locking plate.
ON
OFF
Mortar
Concrete
Unload
Storage
Turning the Mixer On and Off
ON
OFF
Mortar
Concrete
Unload
Storage
1. To start the mixer press the green
on “I” button.
2. To stop the mixer press the red off
“O” button..
ON
OFF
Mortar
Concrete
Unload
Storage
WARNING! HOLD THE CONTROL HANDLE TIGHTLY
WHILE TURNING IT.

For best loading results, proceed as follows:
• Add the required amount of stone into the drum.
• Add the required amount of sand into the drum.
• Add the required amount of cement into the drum.
• Pour the required amount of water into the drum.
Note: When measuring out cement and ballast (or sharp sand/gravel),
use a small bucket to ensure accurate ratios of cement: ballast. Refer
to the instructions that come with your cement.
Ensure your chosen quantity of concrete is large enough that the
cement mixer will function and small enough that it will t in the
drum, see load sizes in specications section of manual to calculate
quantities.
• When the mixture is the right consistency to use, empty the drum.
Pour the mixed cement by releasing the tipping handle and rotating
the drum to the empty position while the machine is running. Be sure
to pour the mix slowly and smoothly to avoid tilting the cement mixer.
• When the drum is empty, turn the cement mixer off.
• Never put any of your body parts (including hands) inside the drum while it is
rotating.
• Wipe off any external material on the motor cover. Do not use petrol,
turpentine, lacquer, paint thinner, dry cleaning uids or similar products.
• The use of chemical products or solvents may damage the motor cover.
• Thoroughly clean your cement mixer at the end of each days operation.
• Keep your cement mixer clean. The slightest trace of material left in the drum
assembly will harden and attract more material each time the machine is used.
• Dried cement should be scraped out of the drum assembly.
• DO NOT throw bricks into the drum assembly to clean it out.
• DO NOT beat on the drum with a shovel, hammer or other tools to break up
accumulation of dried cement mix as the cement mixer may be damaged.
• The drum may be scoured for approximately 2 minutes, using a 1” stone and
water mixture. After this, discharge the stone/water mixture and hose down the
drum assembly inside and out.
• The IP44 protection clad construction of the mixer enables the DRUM
ASSEMBLY ONLY to be hosed down safely. Avoid getting water on the motor
and motor housing, DO NOT wet the motor and motor housing.
General Maintenance
• Ball bearings are packed with grease at the factory. No further lubrication of
bearings is required.
• During normal use, painted surfaces can lose their coating during the mixing
process. Wipe all exposed surfaces regularly with an oily rag to prevent
corrosion. (Note: Loss of paint and rust are not covered under warranty.)
• Keep air vents clean of dust and dirt.
• Remove dust and dirt from the cement mixer regularly with soft cloth, brush or
compressed air. Use a mild detergent and a soft cloth to clean plastic parts.
• If the power cord is damaged, have it replaced by an electrician or a power tool
repairer.
• Regularly check that all bolts, screws and nuts are securely xed as these
could work loose during normal operation.
• Do not open the motor cover under any circumstances.
OPERATION
IMPORTANT! ALWAYS START THE CEMENT MIXER
BEFORE LOADING THE DRUM. LOAD THE DRUM WHILE
IT IS ROTATING.
IMPORTANT! DO NOT TURN THE MIXER OFF WHILE IT’S
FULL OF MATERIAL. EMPTY THE DRUM WITH THE DRUM
ROTATING.
IMPORTANT! ENSURE MATERIAL IS NOT LOADED INTO
THE MIXER ALL AT ONCE. ADD THE MATERIAL STEADILY
OVER THE MIXING BLADES, THIS HELPS TO AVOID
THE MATERIAL FROM STICKING TO THE BACK OF THE
DRUM.
WARNING!
1. DO NOT LET THE SHOVEL MOUTH OR ANY OTHER DEVICES
ENTER THE DRUM MOUTH DURING LOADING.
2. NEVER PLACE HANDS INSIDE THE REVOLVING DRUM OR
NEAR ANY ROTATING PARTS.
3. PLACE THE CEMENT MIXER AS CLOSE AS POSSIBLE TO THE
WORK SITE. DO NOT MOVE THE CEMENT MIXER WHEN LOADED.
4. RETIGHTEN ALL BOLTS ATTACHING MOTOR AND MOTOR
HOUSING ASSEMBLY, DRUM ASSEMBLY AND FRAME ASSEMBLY
AFTER FIRST MIX.
8. LOADING THE DRUM WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING MAINTENANCE.
WARNING! DO NOT POUR OR SPRAY WATER DIRECTLY INTO
OR OVER THE MOTOR COVER.
MAINTENANCE
Note: Ozito Industries will not be responsible for any damage or injuries
caused by the repair of the cement mixer by an unauthorised person or by
mishandling of the mixer.

DESCRIPTION OF SYMBOLSTROUBLESHOOTING
SPARE PARTS
Double insulated
Danger of electric shock
FAULT POSSIBLE CAUSES SOLUTION
The Cement
Mixer does not
start.
Not Connected to mains
power
Connect to mains power
Power cord or plug is
defective.
Contact Ozito customer
service.
Other electrical defect to the
product
Contact Ozito customer
service.
Cement Mixer
does not reach
full power
Extension cord not suitable
for operation with this product
Use suitable extension
cord..
Power source (e.g.
Generator) has too low
voltage.
Connect to another power
source.
Mixing volume is too large Reduce the amount of
material
Unsatisfactory
result
Mixer blades are dull/
damaged
Replace with new ones
Mixer blades not suitable for
work piece material
Use proper mixing blades
Excessive
vibration or
noise
Mixer blades are dull/
damaged.
Replace with new ones
Bolts/nuts are loose. Tighten bolts/nuts.
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse or Homebase
store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: [e-mail]

WARNING! For your own safety, do not try to use your cement mixer or
plug it in until it is completely assembled and installed according to the
instructions and until you have read and understood the following:
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Avoid dangerous conditions. Do not use the mixer in wet or damp areas
or expose it to rain. Do not use it in areas where fumes from paint, solvents or
ammable liquids pose a potential hazard.
• Inspect your cement mixer. Check your cement mixer before turning it on. Keep
guards in place and in working order. Form a habit of checking to see that keys and
adjusting wrenches are removed from the cement mixer area before turning on.
Replace damaged, missing or failed parts before using it.
• Wear protective gear. Foreign objects may be thrown from the cement mixer while
in operation. This can cause facial injuries. Always wear safety goggles and/or face
shields.
• Loading the cement mixer. Do not attempt to load or unload the contents until the
cement mixer has stopped. Keep hands out of the way of all moving parts.
• Never leave cement mixer running unattended. Don’t leave cement mixer until it
has come to a complete stop.
• Disconnect power. Unplug when not in use, before making adjustments, changing
parts, cleaning, or working on the mixer.
• Maintain your cement mixer with care. Clean the cement mixer immediately after
use. Keep the cement mixer clean for best and safest performance.
• Moving the cement mixer. Do not tow the cement mixer by using a vehicle. Use
an approved trailer to move the cement mixer if it is to be transported.
• Drugs, alcohol and medication. Do not operate the mixer while under the
inuence of drugs, alcohol, or any medication that could affect your ability to use it
properly.
CEMENT MIXER SAFETY WARNINGS
GENERAL POWER TOOL SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Donotoperatepowertoolsinexplosiveatmospheres,suchasinthepresenceofammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
notuseapowertoolwhileyouaretiredorundertheinuenceofdrugs,alcoholormedication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
h) This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
i) Children should be supervised to ensure that they do not play with the appliance.
5. Service
a. Haveyourpowertoolservicedbyaqualiedrepairpersonusingonlyidenticalreplacement
parts. This will ensure that the safety of the power tool is maintained.
b) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
WARNING! When using mains-powered tools, basic safety precautions, including the
following,shouldalwaysbefollowedtoreduceriskofre,electricshock,personalinjuryand
material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before
operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The manufacturer cannot accept any liability for damage or accidents which arise due to a failure to follow these
instructions and the safety information.
Before you connect the appliance to the mains supply make sure that the data on the rating plate are
identical to the mains data.
This tool is double insulated therefore no earth wire is required.
The power supply for this product should be protected by a residual current device (rated at 30mA or less). A
residual current device reduces the risk of electric shock.
Note: Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may result in a risk of re and electric
shock.

size 445 x 210 mm
Danger! Read the operating instructions to
reduce the risk of inquiry.
Beware of electrical voltage!
Caution! Wear ear-mus. The impact of noise
can cause damage to hearing.
Caution! Wear a breathing mask. Dust which
is injurious to health can be generated when
working on wood and other materials. Never use
the device to work on any materials containing
asbestos!
Caution! Wear safety goggles. Sparks gene-
rated during working or splinters, chips and dust
emitted by the device can cause loss of sight.
The reprinting or reproduction by any other
means, in whole or in part, of documentation and
papers accompanying products is permitted only
with the express consent of the iSC GmbH.
Subject to technical changes
CMX-125U
GB Additonal operating & safety instructions Cement Mixer
Service information
We have competent service partners in all countries named on the guarantee certicate whose contact
details can also be found on the guarantee certicate. These partners will help you with all service re-
quests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the
following parts are therefore also required for use as consumables.
Category Example
Wear parts* Rubber Gasket, Belt, Rubber Washer, Mixing
Blades
Consumables*
Missing parts
* Not necessarily included in the scope of delivery!
In the eect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Plea-
se ensure that you provide a precise description of the problem and answer the following questions in all
cases:
• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.
Mayr/Product-ManagementWeichselgartner/General-Manager
- 135 -
explains the following conformity according to EU directives and norms for
the following product
Cement Mixer CMX-125U (Ozito)
2014/29/EU
2005/32/EC_2009/125/EC
2014/35/EU
2006/28/EC
X2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X2011/65/EU
X2006/42/EC
Annex IV
Noti ed Body:
Noti ed Body No.:
Reg. No.:
X2000/14/EC_2005/88/EC
XAnnex V
Annex VI
Noise: measured LWA = 93 dB (A); guaranteed LWA = 96 dB (A)
P = 0,55 KW; L/Ø = cm
Noti ed Body: TÜV SÜD Product Service GmbH (0036)
Ridlerstraße 65, 90339 München
2012/46/EU
Emission No.:
Standard references: EN 60204-1; EN 12151; EN 62321;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 06.07.2016
First CE: 16 Archive-File/Record: NAPR014361
Art.-No.: 44.722.91 I.-No.: 11016 Documents registrar: R. Gehard
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
Declaration of conrmity

size 445 x 210 mm
Items supplied
Please check that the article is complete as
specied in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
• Open the packaging and take out the equip-
ment with care.
• Remove the packaging material and any
packaging and/or transportation braces (if
available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for
transport damage.
• If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suocating!
Proper use
The Cement Mixer has been designed to mix buil-
ding materials such as, mortar, adhesive, plaster
and similar substances.The relevant mixing acti-
on (which depends on the consistency of the ma-
terials and the quantity that has to be mixed) must
be set up for the appropriate mixing tool.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Technical data
Mains voltage: ................................. 230V ∼ 50Hz
Motor: ......................................................... 550W
Gross drum volume:.............................. 125 Litres
Drum mouth opening: ...............................375mm
No load speed:....................................... 2950/min
Drum speed: .............................................. 34/min
Unmixed dry volume: ............................ 100 Litres
Mixed wet volume:.................................. 91 Litres
Protection class: ............................................ II/&
Degree of protection: .....................................IP44
Sound and vibration
Sound and vibration values were measured in
accordance with EN 11688.
LpA sound pressure level .........................79 dB(A)
KpA uncertainty .............................................. 3 dB
LWA sound power level .............................96 dB(A)
KWA uncertainty.............................................. 3 dB
Wear ear-mus.
The impact of noise can cause damage to
hearing. Total vibration values (vector sum of
three directions) determined in accordance with
EN 11688.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect wor-
king order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever
necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in ac-
cordance with instructions, certain residual
risks cannot be rules out. The following ha-
zards may arise in connection with the equip-
ment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protecti-
on is used.
3. Health damage caused by hand-arm vibra-
tions if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
For EU countries only
Never place any electric power tools in your
household refuse.
To comply with European Directive 2012/19/EC
concerning old electric and electronic equipment
and its implementation in national laws, old elec-
tric power tools have to be separated from other
waste and disposed of in an environment-friendly
fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to
the manufacturer, the owner of the electrical
equipment must make sure that the equipment
is properly disposed of if he no longer wants to
keep the equipment.The old equipment can be
returned to a suitable collection point that will
dispose of the equipment in accordance with the
national recycling and waste disposal regulations.
This does not apply to any accessories or aids
without electrical components supplied with the
old equipment.