Answer:
Step 1: Plug the two-pronged wall adapter (WA) into the
wall socket.
Step 2: Plug the other end of the WA, the barrel adapter
(BA) into the input 12V/1A on the battery.
Note: The Battery Status indicator lights should begin
ashing when charging. The Battery does not have to be
powered on when charging.
P3Solar • Solar Portables Business, Inc. • 4500 E. Speedway Blvd. Suite 50 Tucson, AZ 85712 USA • 520-775-1390 • [email protected] • www.p3solar.com Dynamo PLUS Quick Start Guide
How do I charge the battery from the wall outlet?
P3Solar
•
4500
E.
Speedway
Blvd.
Suite
50
Tucson,
AZ
85712
USA
•
520-775-1390
•
[email protected] •
www.p3solar.com
How do I start my vehicle from the battery? How do I charge my USB device from the battery?
How do I charge my device from the 12V/16V/19V outlet? How do I charge my device with my 12V CLA / vehicle adapter?
How do I charge the battery from a vehicle MCLA adapter?
Answer:
Step 1: Plug the male cigarette lighter adapter,
(MCLA) into your vehicles 12V receptacle (not
shown).
Step 2: Plug the other end of the vehicle charger,
the barrel adapter (BA) into the input 12V/1A on
the battery.
Note: The Battery Status indicator lights should be-
gin ashing when charging. The Battery does not
have to be powered on when charging
Answer:
Step 1: Turn the master switch,
MS, to “ON” position. Make
sure you have at least 3 of 4
bars on the battery status indi-
cator illuminated, before jump
starting the vehicle. If less than
3 bars then it may not start the
vehicle.
Step 2: Connect Battery cables (BCs) + Positive (Red) to the vehicle batteries Positive (Red) terminal
and the BC’s, – Negative (Black) to the vehicle batteries Negative (Black) terminal.
Step 3: Plug the battery clamps blue plug, (BP) into engine start socket. Start the car then unplug the
BC’s.
Answer:
Step 1: Turn the master switch (MS) to “ON” posi-
tion. Make sure the Output USB 5v light is on.
Step 2: The battery pack comes with a 4-in-1
adapter cable (4-1AC) which can charge differ-
ent devices. Plug the USB plug into the Output USB
5v’s on the battery pack. Plug the corresponding
1 of 4 adapter into your electronic device and
begin charging.
Note: You can also use the USB adapter that
came with your device to plug into the Output USB
5v outlet for device charging.
Answer:
Step 1: Turn the master switch (MS) to “ON”
position. Make sure you have at least 2 of 4
bars on the battery status indicator illuminated,
Step 2: Select your barrel adapter tip (BAT)
from one of 8 different sizes available: A = 6.0mm
x 1.0mm, B= 6.3mm x 3.0mm, C = 5.5mm x 2.5mm, D =
5.5mm x 2.1mm, E = 5.5mm x 1.7mm, F = 4.8mm x 1.7mm,
G = 4.0mm x 1.7mm, H = 3.5m x 1.3mm
Step 3: Plug one end of the BAC into the BAT you wish to use. In the image above, tip C was selected.
Plug the other end of the BAC into the output on the battery pack.
Step 4: Caution: Before plugging into your device, make sure to review How to the select the correct
output voltage on the battery.
Step 5: Plug the BAC into your notebook computer or device and begin charging.
Answer:
Step 1: Turn the master switch (MS) to “ON” posi-
tion. Make sure the battery status indicator lights
are on.
Step 2: Select barrel adapter tip C = 5.5mm x
2.5mm, and connect it to the barrel adapter
cable (BAC)
Step 3: Plug the other end of the BAC into the
output on the battery pack.
Step 4: Plug the FCLA barrel jack to the C tip.
Step 5: Press key switch (KS) to toggle to the 12V
setting.
Step 6: Plug your devices 12V vehicle adapter (not
shown) into the FCLA socket
