Pacific energy BROADWAY User manual

WARNING: If the information in these
instructions is not followed exactly a fire
or explosion may result causing property
damage, personal injury or death.
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Thisappliancemaybeinstalledinan aftermarket
permanently located, manufacturedhome (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of
gas indicated on the rating plate. This appliance
is not convertible for use with other gases
unless a certified kit is used.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapours and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical Switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier call the
fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
BDWY.BODYB / BRNT.BODYB
BROADWAY & BRENTWOOD
INSTALLATION AND
OPERATING INSTRUCTIONS
MODEL: BROADWAY/BRENTWOOD
SERIES: B
DIRECT VENT GAS INSERT
Visit www.pacificenergy.net for the most recent version of this manual
5055.66-B230216-44

BDWY.BODYB
BRNT.BODYB
Table Of Contents
Important Note for the Commonwealth of Massachusetts: ...... 3
Caution ...................................................................................... 4
Safety ......................................................................................... 5
First Fire ..................................................................................... 6
Warnings and Cautions ............................................................. 6
Remote Control Operation ..........................................................7
System Description.............................................................7
Transmitter (Remote Control with LCD Display)..................7
IFC Module......................................................................... 8
Operating Procedure.......................................................... 8
Initializing the system for the rst time. ............................. 8
Temperature indication Display .......................................... 9
Turn on the Fireplace ......................................................... 9
Turn off the Fireplace ........................................................ 9
Manual Bypass of the Remote System.............................. 9
Key Lock ............................................................................ 9
Instructions for enabling the Thermostat
function for Canadian users............................................... 9
Remote Flame Control .................................................... 10
Room Thermostat (Transmitter Operation) ...................... 10
Smart Thermostat (Transmitter Operation) .......................11
Comfort Fan Speed Control..............................................11
Low Battery Power Detection .......................................... 12
Transmitter........................................................................ 12
Receiver ........................................................................... 12
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection ..... 12
Maintenance ............................................................................ 13
Glass Door: ...................................................................... 13
Annual Inspection:............................................................ 13
Periodically:...................................................................... 13
Lighting Instructions ................................................................ 14
Fireplace Dimensions .............................................................. 15
Broadway: ..................................................................... 15
Brentwood: .................................................................. 15
Existing Fireplace Preparation ................................................. 16
Clearances to Combustibles ....................................................17
Mantel Clearance ............................................................ 17
Mantel Depth .................................................................. 17
Venting ..................................................................................... 18
Plumbing and Electrical ........................................................... 19
Gas Supply .............................................................................. 20
Gas pressure requirements.............................................. 20
Gas Pressure Check / Output / Efciency ............................... 20
Broadway ......................................................................... 20
Brentwood ..................................................................... 20
Gas Pressure Testing Procedure ..............................................21
Pilot Adjustment .......................................................................21
Propane Conversion ................................................................ 22
Adjustable leveling bolts .......................................................... 23
Door Installation/Removal ....................................................... 23
Installation........................................................................ 23
Removal ........................................................................... 23
Surround Installation Instructions ............................................ 24
Surround Front Dimensions .................................................... 25
Broadway ...................................................................... 25
Brentwood .................................................................... 25
Fan Removal / Installation ....................................................... 26
Panel Installation / Removal .................................................... 30
Installation........................................................... 30
Removal ........................................................................... 30
Air Deector Installation / Removal ..........................................31
Burner Tray Installation / Removal .......................................... 32
Burner Installation / Removal .................................................. 32
Log Set Installation / Removal ................................................ 33
Rustic Log Set Installation / Removal ..................................... 34
Glass Burner Installation / Removal ........................................ 35
Damper/Air Shutter ................................................................. 36
Replacement Parts ...................................................................37
Wiring Diagram ........................................................................ 38
Broadway Rating Label ........................................................... 39
Brentwood Rating Label .......................................................... 40
2230216-44
5055.66-B

BDWY.BODYB
BRNT.BODYB
Important Note for the Commonwealth of Massachusetts:
From Massachusetts Rules and Regulations 248 CMR 5.08:
(a) For all side wall horizontally vented gas fuelled equipment installed in every dwelling, building or structure used in whole or
in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust
vent termination is less than seven (7) feet above nished grade in the area of the venting, including but not limited to decks
and porches, the following requirements shall be satised.
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas
fuelled equipment,the installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm
and battery back-up is installed on the oor level where the gas equipment is to be installed, in addition, the installing
plumber or gas tter shall observe that a battery operated or hard-wired carbon monoxide detector with an alarm is installed
on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fuelled equipment.
It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the installation
of hard-wired carbon monoxide detectors.
a. In the event that the side wall horizontally vented gas fuelled equipment is installed in a crawl space or an attic, the hard-
wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent oor level.
b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall
have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day
period, a battery operated carbon monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above
provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.
3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fuelled
heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT
DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fuelled equipment shall not approve
the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accor
dance with the provisions of 248 CMR 5.089(2) (a) 1 through 4.
(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54
as adopted by the Board; and
2. Product Approved side wall horizontal vented gas fuelled equipment installed in a room or structure separate from the
dwelling, building or structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with
the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall
include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fuelled equipment does not provide the parts for venting the fuel
gases,but identies “special venting systems”, the following requirements shall be satised by the manufacturer.
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation
instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a
parts list and detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fuelled equipment, all venting
instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
35055.66-B
230216-44

BDWY.BODYB
BRNT.BODYB
This replace is equipped with a micro mesh safety screen for your protection and
must be installed with the unit. Removal of the safety screen will cause the replace
to become a burn hazard.
Caution
FOR YOUR SAFETY - Do not install or operate your Town & Country replace without rst reading
and understanding this manual. Any installation or operational deviation from the following instruc-
tions voids the Town & Country FireplacesTM Warranty and may prove hazardous.
This appliance and its individual shut off valve must be disconnected from gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).
This appliance must be isolated from the gas supply piping system by closing its individual manual
shut off valve during any pressure testing of the gas supply piping system at test pressures equal to
or less than 1/2 psig (3.5 kPa).
Note: When lit for the rst time, the appliance will emit a slight odour for a couple of hours. This
is due to the curing of paints, sealants and lubricants used in the manufacturing process. This
condition is temporary. Open doors and windows to ventilate area. Smoke and fumes caused by the
curing process may cause discomfort to some individuals.
Do not use the replace if any part has been under water. Immediately call a qualied service
technician to inspect the replace and to replace any part of the control system and any gas control
which has been under water.
4230216-44
5055.66-B

BDWY.BODYB
BRNT.BODYB
Safety
• Due to high temperatures, this gas appliance should be located out of trafc and away from
furniture and draperies.
• Children and adults should be alerted to the hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical
barrier is recommended if there are at risk individuals in the house. To restrict access to a
replace or stove, install an adjustable safety gate to keep toddlers, young children and other at
risk individuals out of the room and away from hot surfaces.
• Clothing or other ammable material should not be placed on or near the appliance.
• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the
Surround Kit component and shall be installed.
• If the barrier becomes damaged, the barrier shall be replaced with the manufacturers barrier
for this appliance.
• Any grill, panel or door removed for servicing the unit must be replaced prior to operating.
• Installation and repair should be done by a qualied service person. The appliance should be
inspected before use and at least annually by a professional service person. More frequent
cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is
imperative that control compartments, burners and circulating air passageways of the appliance
be kept clean.
• This appliance must not be connected to a chimney ue serving a separate solid fuel burning
appliance.
• It is our policy that no responsibility is assumed by the Company or by any of its employees or
representatives for any damages caused by an inoperable, inadequate, or unsafe condition which
is the result, either directly or indirectly, of any improper operation or installation procedures.
55055.66-B
230216-44

NOTE: Fireplace may take up to
30 seconds to ignite each time the
“ON” button has been selected
First Fire
Congratulations on your purchase of a Pacific Energy Gas Appliance.
Your replace has been professionally installed by:
Dealer name: ___________________________________________________
Phone Number:___________________________________________________
If you discover any problems with your gas appliance contact your dealer immediately to have the
unit repaired.
Caution: Do not attempt to repair the replace because you may cause injury to yourself or others,
and risk causing damage to the unit.
Before operating your appliance carefully read this manual and pay close attention to all Safety
Warnings.
The manual contains important information on the unit’s safe operation and maintenance.
When lit for the rst time, the replace will emit a slight odour for a couple of hours. This is due to
the curing of paints, sealants and lubricants used in the manufacturing process. This condition is
temporary. Open doors and windows to ventilate area. Odour caused by the curing process may
cause discomfort to some individuals.
It is normal for replaces fabricated of steel to give off some expansion and/or contraction noises
during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or
cook stove oven.
Warnings and Cautions
WARNING
Fire Hazard. Can cause severe injury or death
The Receiver causes ignition of the appliance. The appliance can turn on suddenly. Keep away from the
appliance burner when operating the remote system or activating manual bypass of the remote system.
WARNING
Shock Hazard. Can cause severe injury or death
This device is powered by line voltage. Do not try to repair this device. In no way is the enclosure to be
tampered with or opened. Disconnect from line voltage before performing any maintenance.
BDWY.BODYB
BRNT.BODYB
6230216-44
5055.66-B

Remote Control Operation
System Description
The Proame 2 Remote Control System consists of two elements:
1. Proame 2 Remote Control Transmitter.
2. Proame Integrated Fireplace Control (IFC) (Figure 3) board and a wiring harness to connect the IFC to
the gas valve and stepper motor - See “Figure 29” on page 21.
Transmitter (Remote Control with LCD Display)
The Proame 2 Transmitter uses a streamline design with a simple button layout and informative LCD
display (Figure 1). The transmitter is powered by 3 AAA type batteries. A Mode key is provided to Index
between the features and a Thermostat key is used to turn on/off or index through thermostat functions
(Figure 1 and Figure 2)
Blue back lit LCD display
ON/OFF Key
THERMOSTAT Key
UP/DOWN Arrow Key
MODE Key
Figure 1: Proame 2 handset.
OFF
ON
SMART
MAX MAX
KEY LOCK
LOW BATTERY ALARM
ROOM
TEMPERATURE
CPI MODE
DIMMER ONDIMMER ON
SET POINT:
TEMPERATURE/LEVEL/STATE
THERMOSTAT OFF/
ON/SMART
TRANSMISSION
* SEE NOTICE REGARDING
THERMOSTAT USE
* SEE NOTICE REGARDING
THERMOSTAT USE
* SEE NOTICE REGARDING
COMFORT FAN
Figure 2: Proame 2 LCD display.
BDWY.BODYB
BRNT.BODYB 75055.66-B
230216-44

IFC Module
The Proame 2 Integrated Fireplace Control (IFC) module (Figure 3) is a device that allows automatic ignition
and pilot ame supervision, and commands the functions of the hearth Heater. It’s congured to control the
ON/OFF main burner operation, giving the choice of both IPI (intermittent pilot ignition), and CPI (continuous
pilot ignition) modes. The Proame 2 IFC module controls and connects directly to the pilot assembly and the
automatic valve using low electric power.
The IFC module can be powered by both an AC power supply, and battery pack for back up. The Proame
2 offers the added ability to control the comfort fan speed from OFF through six (6) speeds, a remotely
actuated auxiliary outlet and a dimmable light outlet. The external batteries can provide DC power to the IFC
allowing the batteries to be used only when line power is interrupted or lost, and if the Heater does not use a
combustion fan.
Operating Procedure
Initializing the system for the rst time.
1. Install 4 AA batteries into the battery holder (Figure 4) located on the rear side behind the surround below
the rebox. Install the ON/OFF switch cover (Figure 5) over top of the battery bay. Make sure that the selec-
tion switch is on the “Remote” setting.
2. Install 3 AAA batteries into the Proame 2 Remote Transmitter (Figure 1).
3. Plug the power cord into the Brentwood/Broadway and open the gas supply line.
4. Insert a straightened paper clip into the opening marked “PRG” of the ON/OFF battery holder cover
(Figure 4 and Figure 5) and press the program button once. The module will beep 3 times indicating that it
is ready to synchronize with a remote transmitter.
5. On the remote transmitter, push the power on button once. The remote transmitter will beep 4 times to
indicate that the remote transmitter and the control module are now synchronized. The remote transmitter
is now ready to use.
Figure 3: IFC Module.
Figure 4: On - Off Switch - Battery
holder.
Figure 5: On - Off Switch cover.
BDWY.BODYB
BRNT.BODYB
8230216-44
5055.66-B

Figure 6: Temperature in
celcius.
Figure 7: Temperature in
fahrenheit.
Figure 8: Key lock icon.
BDWY.BODYB
BRNT.BODYB
The thermostat key (Figure 1) on the remote handset needs to be held down. Keep it pressed down and
remove one of the three batteries from the remote handset. Simply re-install the battery that was removed
and the feature is activated. Use the same procedure to disable the thermostat function.
Instructions for enabling the Thermostat function for Canadian users.
Temperature indication Display
With the system in the “OFF” position, press the Thermostat Key and the
Mode Key at the same time. Look at the LCD screen on the transmitter to
verify that a C or F is visible to the right of the Room Temperature display
(Figure 6 and Figure 7).
Turn on the Fireplace
With the system OFF, press the ON/OFF Key on the remote transmitter. The
remote transmitter display will show some other active Icons on the screen.
At the same time the Receiver will activate the Heater. A single “beep” from
the Receiver (module) will conrm reception of the command.
Turn off the Fireplace
With the system ON, press the ON/OFF Key on the Remote transmitter.
The Remote transmitter LCD display will only show the room temperature
(Figure 6 and Figure 7). At the same time the Receiver (module) will turn off
the Heater. A single “beep” from the Receiver conrms reception of the
command.
Manual Bypass of the Remote System
If the batteries of the receiver or remote transmitter are low or depleted, the
Heater can be turned off manually using ON/OFF switch located on battery
box at the rear of the Broadway/Brentwood. This will bypass the remote
transmitter.
Key Lock
This function will lock the keys to avoid unsupervised operation. To activate
this function, press the MODE and UP keys at the same time. The lock icon
will appear (Figure 8). To de-activate this function, press the MODE and UP
keys at the same time.
95055.66-B
230216-44

BDWY.BODYB
BRNT.BODYB
Remote Flame Control
The Proame has six (6) ame levels. With the
system on, and the ame level at the maximum in
the appliance, pressing the down arrow key once will
reduce the ame height by one step until the ame is
turned off.
The Up Arrow Key will increase the ame height each
time it is pressed. If the Up Arrow Key is pressed
while the system is on but the ame is off, the ame
will come on in the high position (Figure 9). A single
“beep” will conrm reception of the command.
Room Thermostat (Transmitter Operation)
The Remote Control can operate as a room thermostat. The thermostat
can be set to a desired temperature to control the comfort level in a room.
To activate this function, press the Thermostat key (Figure 1). The LCD
display on the transmitter will change to show that the room thermostat
is “ON” and the set temperature is now displayed (Figure 10). To adjust
the set point, press the up or down arrow keys until the desired set point
temperature is displayed on the LCD screen of the transmitter.
Flame Off
Flame level 5
Flame level Max
Flame level 1
Figure 9: Flame level control.
Room Temperature
Set Temperature
Figure 10: Room temperature control.
10 230216-44
5055.66-B

BDWY.BODYB
BRNT.BODYB
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the ame height in accordance to the difference between the set point
and the room temperatures. As the room temperature gets closer to the set point, the Smart Function will
modulate the ame down. If the room temperature is cool, the Smart Function will modulate the ame up. To
activate this function, press the THERMOSTAT key (Figure 1) until the word “SMART” appears to the right of
the temperature icon (Figure 11). To adjust the set point, press the up or down arrow keys until the desired set
point temperature is displayed on the LCD screen of the remote transmitter (Figure 12).
Comfort Fan Speed Control
If the Heater is equipped with a hot air circulating fan, the speed of the fan can be controlled by the Proame
2 System. The fan speed can be adjusted through six (6) speeds. To activate this function use the Mode Key
(Figure 1) to index to the fan control icon (Figure 13). Use the Up/Down Arrow Keys to turn on, off or adjust
the fan speed (Figure 14). A single “beep” will conrm reception of the command.
Figure 11: Smart ame
control.
Figure 12: Smart ame
function set low.
Figure 13: Comfort fan HI. Figure 14: Comfort fan off.
11 5055.66-B
230216-44

Low Battery Power Detection
Transmitter
The life span of the remote control batteries depends on various factors: quality of the batteries used, the
number of ignitions of the Heater, the number of changes to the room thermostat set point, etc.
When the remote batteries are low, an icon will appear on the LCD display of the remote (Figure 17) before all
battery power is lost. When the batteries are replaced this icon will disappear.
The life span of the IFC module batteries depends on various factors: quality of the batteries used, the
number of ignitions of the Heater, the number of changes to the room thermostat set point, etc.
When the IFC batteries are low, a “double-beep” will be emitted from the IFC module when it receives a
command from the remote. This is an alert for a low battery condition for the IFC board. When the batteries
are replaced, a single “beep” will be emitted from the IFC module when a key is pressed. See “Initializing the
system for the rst time.” on page 8
Receiver
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
With the system in the “OFF” position, press the Mode Key (Figure 1) to index to the CPI mode icon (Figure 16).
Pressing the Up Arrow Key will activate the Continuous Pilot Ignition mode (CPI). Pressing the Down Arrow Key
will return to IPI. A single “beep” will conrm the reception of the command.
Figure 15: IPI Mode. Figure 16: CPI Mode.
Figure 17: Key lock icon.
BDWY.BODYB
BRNT.BODYB
12 230216-44
5055.66-B

Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
BDWY.BODYB
BRNT.BODYB
Maintenance
CAUTION:
Turn off gas and electrical power supply (if applicable) and allow ample time for
unit to cool before servicing appliance. It is recommended that the replace and
its venting should be inspected at least once a year by a qualied service person.
Glass Door:
Warning: Do not operate replace with glass panel removed, cracked or broken.
Replacement of the glass panel should be done by a licensed or qualied service
person.
Do not strike or otherwise impact the glass in anyway that may cause it to break.
If the glass becomes cracked or broken it must be replaced before using the
replace. Replacement glass can be obtained from your nearest Town & Country
FireplacesTM dealer. The size required is 52" x 16" x 5mm. Use ceramic glass only.
Do not substitute with any other type.
To remove broken glass, remove window frame as noted in See “Door Installation/
Removal” on page 23.
Unclip the Glass Retainer Clips located at the top and sides of the Window
Frame. Pull the top edge of the glass out of the frame rst, then lift it up and out
of the bottom edge.
Install the new piece of glass with the gasket into the frame so that the thicker bead of gasket faces the replace.
Re-install glass retaining clips.
Annual Inspection:
a) Remove glass panel and pebble assemblies. Inspect pebble and burner assemblies for soot buildup. If excessive
buildup of soot is present, have a qualied service person inspect and adjust unit for proper combustion. Clean logs
and burner with a brush or vacuum cleaner, paying close attention to burner ports.
b) Check the pilot system for proper ame size and operation. Clean pilot free of soot, dust or any other deposits (See
Figure 18).
c) Check that the vent pipe and vent terminal are open and free from blockage or debris. If the venting is disassembled
for cleaning, it must be properly assembled and re-sealed. See “Venting” on page 18 for proper procedure.
d) Check glass panel gasket, replace if necessary. It is important that the glass seal be maintained in good condition.
e) Check and replace batteries as needed.
Note: The appliance area must be kept clear and free from combustible materials, gasoline and other ammable
vapours and liquids.
Periodically:
a) Viewing glass may be cleaned as necessary with replace glass cleaner.
b) Exterior nish may be cleaned with mild soap and water.
CAUTION:
Do not use abrasive cleaners on glass or any other part of the replace.
Do not clean glass when hot.
PILOT FLAME
FLAME SENSOR
Figure 18: Pilot assembly.
ELECTRODE
PILOT
13 5055.66-B
230216-44

BDWY.BODYB
BRNT.BODYB
Lighting Instructions
14 230216-44
5055.66-B

Figure 19: Broadway dimensions.
Figure 20: Brentwood dimensions.
BDWY.BODYB
BRNT.BODYB
Fireplace Dimensions
Broadway:
Brentwood:
15 5055.66-B
230216-44

Figure 21: Cavity dimensions.
Dimension Broadway Brentwood
A 13” 15”
B 21” 23”
C 26” 34”
BDWY.BODYB
BRNT.BODYB
Existing Fireplace Preparation
The Broadway and Brentwood Gas inserts are certied to be installed into pre-existing approved re place
cavities. The minimum cavity requirements are listed in Figure 21below.
Before installing the Broadway or Brentwood inserts have the chimney swept and replace, including ash
dumps and clean outs, cleaned to remove any creosote and soot residue that may cause odors and stains
after the insert has been installed. The replace chimney should be in good working order and made of
non-combustible material. Make sure chimney cleanouts t properly.
When preparing an existing replace to install a gas insert, any modications that will compromise the
integrity of the existing replace are not allowed. To make way for the insert’s venting the replace ue
dampener may be blocked open or removed. Refractory, glass doors, screen rails, screen mesh and log
grates can be removed from the replace before installing the insert. Also, smoke shelves, shields and
bafes may be removed if attached by mechanical fasteners. Cutting any sheet metal parts of the replace,
in which the gas replace insert is to be installed, is prohibited.
If the factory-built replace has no gas access hole(s) provided, an access hole of 1.5” (37.5mm) or less
may be drilled through the lower sides or bottom of the rebox in a proper workmanship like manner. This
access hole must be plugged with non-combustible insulation after the gas supply line has been installed.
16 230216-44
5055.66-B

• Fireplace Surround Fronts located onpage 25.
• Fireplace Surrounds and oversize backing plates for larger
fi replace openings located on page 25.
• Fronts and Surrounds part numbers located on page 37.
Figure 22: Mantel clearances.
8” 8”
Figure 23: Sidewall clearances.
*
Note on Hearth distance requirement
Although a 16” hearth is required on the
Brentwood replace, there is no requirement
for a hearth on the Broadway replace.
*
BDWY.BODYB
BRNT.BODYB
Clearances to Combustibles
Mantel Clearances
Broadway Brentwood
A
B
C
20 1/2”
16”
12”
32”
32”
32”
Mantel Depth
D 12”
E 9”
F 6”
Minimum hearth depth
As measured from glass
17 5055.66-B
230216-44

Figure 24: Flue adapter plate connections.
Figure 25:
High wind
vent terminal.
BDWY.BODYB
BRNT.BODYB
Figure 26: Co linear venting.
Venting
Note: The following Simpson Duravent kits are
recommended for use with this appliance.
High-Wind
(Broadway 46DVA-CL33)
(Brentwood 46DVA-CL34)
Prairie Co-Linear Kit
(Broadway 46DVA-CL33P)
(Brentwood 46DVA-CL34P)
Only certified venting systems or components may be
installed with this fireplace.
1. Measure chimney height, cut ex liner (min.10’) as
required. Mark one pipe at both ends to identify
combustion air intake pipe from ue outlet pipe.
2. Attach marked ex liner pipe to the intake side of vent
terminal. Seal and secure with sealant and screws
provided. Attach the other pipe to the outlet side of
vent terminal. Seal and secure with sealant and screws
provided.
3. Insert both ex liners from top of the chimney, down
through the damper opening.
4. Before attaching vent terminal to top of chimney, apply
a bead of caulking to top of clay liner. Slip vent terminal
over liner and secure in place with lateral retaining bolts.
5. For larger chimneys, an optional ashing is avail-
able which may be cut and tted to suit. The ashing
attaches to the underside of the terminal with four nuts
provided. Caulk the ashing in place to seal any gaps.
16’-25’
1” Open
10’-16’
Full Open
**Intake Damper Position**
Min. Vent Height
10’ (3m)
**NOTE**
Intake Damper Position
adjustment may vary
depending on particular
installation
Max Vent Height
50’ (15.25m)
25’-50’
3/4” Open
NOTE:
Brentwood has a 4 inch
dia. exhaust vent and a 3
inch intake vent.
Broadway has both 3
inch dia. exhaust and
intake vents.
Intake
Air
Exhaust
Air
18 230216-44
5055.66-B

Figure 27: Gas and electrical connections.
BDWY.BODYB
BRNT.BODYB
Plumbing and Electrical
Note: Installation requires that an electrical outlet be installed into existing fireplace cavity before
insert is installed.
To make the required electrical and gas connections start by positioning the gas insert within the existing
replace. Connect the gas supply line to the 1/2” ex tubing that extends out of the unit as seen in Figure 27.
Please see the gas supply section of the manual for requirements of the gas supply. Next, plug the power
cord into the unit as shown in Figure 27 and plug them into the electrical outlet within the existing replace
cavity.
NOTE: The appliance, when installed must be electrically grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code,
CSA C22.1.
19 5055.66-B
230216-44

BDWY.BODYB
BRNT.BODYB
Gas Supply
Gas pressure requirements
Input Pressure Natural Gas Propane
Minimum 5.0” WC 11.0” WC
Maximum 13.9” WC 13.9” WC
Manifold Pressure
High 3.5” WC 10” WC
Low 1.6” WC 6.4” WC
Gas Pressure Check / Output / Efficiency
Broadway
Gas Orifice Output AFUE
NG 1.98mm 18,000 btu/hr 76%
LP 1.25mm 17,000 btu/hr 76%
Brentwood
Gas Orifice Output AFUE
NG 2.55mm 30,000 btu/hr 75%
LP 1.50mm 26,000 btu/hr 75%
Servicing of the appliance can be performed from the front of the unit by removing the front trim, or by
removing the gas tray from the unit.
Caution: The gas line should be installed by a qualied service person in accordance with all building codes.
This section is intended as a guide for qualied technicians installing this appliance. Consult local and/or
national building codes before proceeding.
• Gas supply line connection is located on the side of the insert. Gas connection accepts a 3/8” N.P.T. t-
ting. Correct gas line diameter must be used to assure proper operation and pressure.
• The replace input rating is shown in the chart below.
• A drip leg must be installed in the gas supply line going to the gas control valve to minimize the possibility
of any loose scale or dirt within the gas supply line from entering the control valve.
• It is essential that a union or anged connection be installed just upstream of the valve and inside the
control compartment to allow for repair or replacement of the gas valve.
Check local codes for additional requirements.
Turn on the gas supply and check that all connections are tight and leak free.
Please refer to following page for gas pressure testing procedure.
WARNING: The gas tray including gasket must be reinstalled after conversion/installation
or servicing has been completed.
20 230216-44
5055.66-B