Pacific Image Electronics RapidScan One User manual

Pacific Image RapidScan One Reader
(Non-sterile)
User Manual
2021
1

2
Product Name Pacific Image RapidScan One
Reader (Non-sterile)
Purpose of Usage
Use the instrument to objectively
read the C or T line of the rapid test.
Principle Reflectance
Intended Use Pacific Image RapidScan One
Reader (Non-sterile) uses the
principle of reflectance to analyze
the C & T line displayed on the
rapid test inserted into the
instrument, and then determine
whether the test item result is
positive or negative.
Side Effects or
Complications None
Contraindications
None
Warnings and
Precautions
1.
This product is not waterproof.
Do not get wet.
2.
If the product is dropped
severely, it will damage the
electronic parts. Please use it
with care.

Contents
Appearance introduction……………………………………………..P4
Stand-alone operation
—Indicator light………..…….…………………………………………..P6
Mobile device connection operation
—Connect teaching……………………………..……………………...P8
—Home screen………….…………………..………………………..….P9
System page ………………………………………………………………P11
—User & User-Add……………………..…………………………….P12
—User Management..……………………………………………….P13
— Test Profile…….…………….…………………………………………P14
— Database………………………………………..………………………P15
—Setting-Network (AP mode)………………………….....……P16
—Setting-Network (Client mode)………………….……….....P17
—IP Finder…………………………………………………………………P18
—Setting-Update Firmware…………………….…………………P20
— Information……….……………………………………………………P21

Product
Introduction
4

Appearance Introduction
Indicator light Analysis button,
switch button
(Short press to
turn on, long
press to turn off)
For Ethernet cable
and USB port
Rapid test
insertion port
Heat-transfer
passage
Power supply
insertion hole
5

Non-exclusive match
•We need to communicate and cooperate with
the rapid test manufacturer about the reader in
advance, and the manufacturer will define the
criteria of the image value after the experiment,
and then set the cut-off value and the
judgment standard of negative and positive.
•Therefore, it can be interpreted as long as the
above content is set. There is no specific rapid
test for this reader.
•The rapid test manufacturer which is
cooperating with us now for example is like 瑞
凌庚 (幽門螺旋桿菌快篩)。
6

Instructions
•There are two ways to use: stand-alone
operation & mobile device connection
operation (more detailed instructions will be
given after page 9.)
•For stand-alone operation, you can easily use
the button to analyze the reading value, and
use the indicator light on the surface to
determine whether the sample is positive or
negative.
•The mobile device connection operation is to
transmit a WiFi signal through the reader and
connect the mobile device, and then you can
log in to the internal screen of the machine
through a browser for more advanced
operations.
7

Software description
& working principle
•It is necessary for the rapid test manufacturer
to use software to set the detection range of
the C line and T line, and conduct experiments
through the cooperation of both parties; after
the experiment, the results are converted into
data settings in the reader, and then the
threshold for judging negative and positive is
defined.
•The software itself has the function of analyzing
and processing images, and the interpretation
time is about 7 to 15 seconds; when the user
presses the analysis button, the reader will
shoot the image of the rapid test, and analyze
the C line in the reading range according to the
manufacturer's settings Line and T-line values
are compared to the threshold to give a
positive or negative result.
8

Stand-alone
operation
9

Indicator light
Orange light: positive (+)
Green light: negative (-)
Flashing orange light:
invalid result
Flashing red light: UV-C disinfection
No light: UV-C off
Turn on for 3 seconds when the analysis
is complete, and turn on for 3 seconds
when the rapid test is taken out.
Tap once to start the analysis.
When it is turned on,
the orange light flashes.
When it is standing by,
the green light shows.
When the light flashes
green,
analysis is in progress.
Put in the rapid test.
(There is a sensor inside. If the rapid
test cannot be detected, the device
will not display any result lights.) 10

Mobile device
connection operation
11

Connect Reader to mobile
device via Wi-Fi
Turn on the Wi-Fi of your mobile
device and find "RS_One_xxxxxxx",
which is the SSID of RapidScan One.
(No password required when
connecting to Wi-Fi)
If you encounter any difficulties,
please contact your provider.
12
Connect to the Web UI
through a browser
Open the browser (Chrome, IE or
Safari), and enter 192.168.0.1 in the
URL bar. (This method is called AP
Mode, see page 15 for details.)
Your browser will connect to the
login page.
Please enter:
User: Admin
Password: 0000
(Other users can also be added in
the future)
Press login to enter the homepage.

Home Page
Test Profile
Select product information
from this section.
Information
The inspector (the account
name used when logging in and
cannot be changed) and
sample No. (can be changed)
System
For system settings
Run Test
Press the button to get instant
results.
Set Delay
Use the button to delay the
image capture time.
(See the dialog box at the
bottom left.)
After using the set delay,
the dialog on the left will
be displayed; at first, the
preset minutes of the file
will be displayed, but you
can still set 1 to 100
minutes according to your
needs.
13

Home Page
Time
Date/time of the most
recent test
Test Result
1. C line value
2. T line value (T2, T3 line... etc.)
3. Result: value or statement
(positive or negative)
4. Image captured by the reader
Click the picture to
enlarge the image.
14

Click the gear wheel
User
Manage user accounts
Test Profile
Add or delete product
information
Database
Test results are sorted by
date/time
Settings
Management system settings
Logout
Log out of current account
System
15
This is the serial number of the
software and firmware version.

System: User
User
Admin users can add/remove
user accounts in this section.
System: User-Add
User-Add
Set ID/password and various
levels of users. Only Admin
can use this function.
Provide 3 authorization levels
(from low to high):
User
User-all
Admin
16

User Management
•Rapid Test View software has permission management function, which
enables users of different levels to obtain different test results.
•ADMIN
–ADMIN is the user's management level: he/she can view all test
results.
–ADMIN can add/delete/edit USER-ALL and USER level users
–Only ADMIN can change the ID/password of USER-ALL and USER
level users
•USER-ALL
–USER-ALL is the leader of the team: he/she can see the test results
of all USER.
•USER
–USER can only see the test results of his own samples.
17

System: Test Profile
Calibrate
Insert blank rapid test for
calibration
Import File
Add product information
Scan QR
Scan QR code
Delete
Delete product information
Live Viewer
Only the administrator
(Admin) can preview the
current screen.
18

19
Database
Record all test results
information; users can select
date/time to find test results.
Click on the picture to
enlarge the picture.
Scroll down to see more test
results (if more than 1 page)
System: Database
Click the button pointed
by the red circle, you can
choose to download the
test data to your mobile
device or USB disk.

System: Settings-Network
(AP Mode)
In AP mode, One acts
as the host, which can
establish a connection
via WiFi and use the
webpage to operate.
Do not change the
settings here.
Admin level users can
change the SSID of the
reader here.
20
After setting, open the browser and enter the URL 192.168.0.1,
then you can jump to the web page for manipulation.