Pacific B-1500 User manual

PLEASE READ THIS BOOK
This operator’s book has important informaon for the use and safe operaon of this machine. Read this
book carefully before starng the machine. Keep this book and tell all operators to read the book. If you
do not follow the instrucons, you can cause an injury or damage equipment, furniture or buildings.
For new books, please download your copy from our website www.pacicoorcare.com or write to:
Pacic Floorcare
2259 S. Sheridan Drive
Muskegon, MI 49442-6252
Carefully inspect all components to ensure that there is no concealed freight damage. If such damage is
discovered, le a “CONCEALED DAMAGE REPORT” immediately with the delivering carrier.
The contents of this manual are based on the latest product informaon available at the me of
publicaon. Pacic reserves the right to make changes or improvements without noce.
Thank you for purchasing a Pacic Floorcare product. Warranty registraon will allow us to beer
serve you over the lifeme of the product. For quick and easy registraon, go to:
www.pacicoorcare.com/Register Product.
PARTS & OPERATING MANUAL
B-1500 BURNISHER
1500 RPM WITH ABS BASE

IMPORTANT SAFETY INSTRUCTIONS
To ensure the safe operaon of this machine, you must read and understand all warnings and instrucons in this book. If you
do not understand, ask your supervisor.
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE
WARNING: To reduce the risk of re, electric shock, or injury:
1. You must be trained to operate this machine. This machine is to be operated for its intended use only.
2. Do not operate this machine unless it is completely assembled.
3. Always use a three-wire electrical system connected to the electrical ground. For maximum protecon against electrical
shock, use a circuit that is protected by a ground fault circuit interrupter. Consult your electrical contractor.
4. To prevent electric shock, always remove the electrical plug from the electrical outlet before doing any repairs or mainte-
nance and when leaving the machine unaended.
5. To prevent electric shock, keep the machine surface dry. Do not subject to rain. Store the machine in a dry building area.
Clean the machine with a dry cloth only.
6. Machines can cause an explosion when near ammable materials and vapors. Do not use this machine with or near fuels,
grain dust, solvents, thinners, or other ammable materials. Do not use ammables to clean this machine.
7. A qualied or authorized person must do maintenance and repairs.
8. To prevent damage to the power cord, do not move this machine over the power cord. Always li the power cord over
the machine. Do not pull or carry cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or
corners. Keep cord away from heated surfaces.
9. Do not use with damaged cord or plug. If the machine is not working as it should, has been dropped, damaged, le out-
doors, or dropped into water, return it to a service center.
Grounding Instrucons
This machine must be grounded. If it should malfuncon or break down, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This machine is equipped with a cord having an equipment-grounding
conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
WARNING - Improper connecon of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do
not modify the plug provided with the machine - if it will not t the outlet, have a proper outlet installed by a qualied
electrician.
This machine is for use on a nominal 120-volt circuit, and has a ground-
ed plug that looks like the plug illustrated in gure A. A temporary
adapter that looks like the adapter illustrated in gures B and C may be
used to connect this plug to a 2-pole receptacle as shown in gure B
if a properly grounded outlet is not available. The temporary adapter
should be used only unl a properly grounded outlet (gure A) can be
installed by a qualied electrician. The green colored rigid ear, lug, or
the like extending from the adapter must be connected to a perma-
nent ground such as a properly grounded outlet box cover. Whenever
the adapter is used, it must be held in place by a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permied by
the Canadian Electrical Code
EXTENSION CORDS
Use only three-wire 12/3 or larger gauge approved extension cords
that have three-prong grounding type plugs and three-pole receptacles
that accept the appliance’s plug. Replace or repair any damaged cords
or plugs.
When servicing, refer to authorized person only. Use only idencal
replacement parts.
NOTE: Do not use adapters shown in
gures B & C in Canada

OPERATING PROCEDURES
WARNING! For the safe operaon of this machine follow the instrucons given in this booklet and the training given by
your supervisor. Failure to do so can result in personal injury and/or damage to machine and property!
DO NOT OPERATE MACHINE IN AN EXPLOSIVE ENVIRONMENT!
The models shown in this manual are intended for commercial use. THIS MACHINE IS NOT INTENDED FOR SPRAY BUFFING.
USING THIS UNIT FOR SPRAY BUFFING WILL VOID WARRANTY.
PREPARATION
To prepare the machine for operaon, make sure it is of correct voltage and properly assembled. If in doubt, ask your su-
pervisor.
Your new oor machine operates in a straight-line forward moon, rather than the normal side to side moon of a conven-
onal single disc machine. Be prepared by having your oor area cleared and ready for the fast acon of a burnisher.
Prepare the oor area by sweeping, dusng or mopping as needed. Check the proper applicaon recommendaons and
procedures found on the label of your nish container. IF IN DOUBT, CALL YOUR SUPERVISOR .
WARNING! NEVER USE THIS MACHINE WITH FLAMMABLE OR EXPLOSIVE MATERIAL!
For Burnishing: Select the correct clean oor pad (your supplier can help you). The lighter color oor pads (bu or white) are
normally used for the burnishing procedure.
NEVER OPERATE THE MACHINE WITHOUT THE FLOOR PAD INSTALLED!
It is very important to select clean, dry pads of uniform thickness. Pads with high or low secons, or hard or so spots are
unacceptable. Pads of open weave are recommended; because close weaves tend to load up fast, bog down the machines,
cause circuits to overload and generally give poor results.
Unplug the machine from the wall outlet and then p the machine back to expose the pad driver. Remove the pad center
lock ring. Carefully center the pad onto the pad driver and secure with the locking ring. Check for level, centering and at-
ness.
OPERATION
Set the machine upright onto the pad. Plug the machine’s power cable into a properly grounded outlet (see Safety Instruc-
ons). Next, release the handle by unlocking the knob and allow the handle to lower into a comfortable posion. THEN
ALWAYS SECURE THE HANDLE LOCKING KNOB. This will allow the operator to easily control the pad pressure.
Depress the handle slightly to elevate the pad from the oor. This is to avoid burning the oor on inial start up, before the
operator is ready to move forward. Pull out on the “Watch Dog” Safety Lock buon and start the machine by depressing
either the le or right switch levers.
When you’re ready to move forward, lower the machine head and pad to the oor and proceed forward in a straight line, at
a steady pace.
MAINTENANCE
AFTER EACH USE: Store the machine in a clean dry area. Wipe the enre machine and cord down with a clean cloth.
Remove the pad and clean thoroughly. Wrap the machine’s electrical cord onto the handles and the cord hook provided.
CHECK the cord and plug for nicks, cuts or damage. Report these to your supervisor for correcon.
WARNING! Always disconnect the machine’s electrical plug from the electrical outlet before performing any service, main-
tenance, pad changing or inspecon of the machine.
MOTOR: The motor is lubricated for life under normal use. No oiling or greasing is necessary. However, if the machine is
used in dusty areas the motor should be cleaned. Blowing the motor out with compressed air or with the exhaust from a
vacuum is suggested. Keeping the motor clean will allow the clear passage of air for venlaon and prevent overheang.
BELT TENSION: Proper belt tension is important for smooth operaon and belt life. Check the belt tension and have no
more than a 1/8-inch deecon. If adjustment is needed, loosen the four (4) motor mounng bolts. Then move the motor
and reghten the four (4) motor mounng bolts.
CARBON BRUSH INSPECTION: Long life 3000-hour carbon brushes are installed in the motor. The machine is also equipped
with a carbon brush wear indicator light to signal when a carbon brush change is required.

4
B-1500 BURNISHER, ABS BASE
1
485904 - Pad Assembly, Flex Drive
1
2
3
4
5
6 7
8
9
10
11
12
13
14 15
16 17
18
19
20
21
22
23
24
25
26
27
28
29
30
19
31
32
30
33
34
35
19
19
36
37
38
39 40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
48
55
47
56
57
58
59 60
61
62
47
63
64
65 66
67
72
73
74
75
76
72
73
71
77
71
72
68
69
70
71

ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.
1962002 Screw, 10-32 x 1/2 Oval 2 42 502396 Cover, Motor 1
2504810 Interlock Assembly 143 See Pg. 7 Motor, 1.5HP DC 1
3962011 Screw, 10-32 x 1 3/4 Oval 2 44 502481 Collar, Upper Shaft 1
4486407C Cover, Switch Box 145 920002 Nut, 3/8-16 Hex 4
5980018 Washer, #10 C-Sunk External 1 46 980009 Washer, 3/8 Lock 4
6509821 Washer, Rubber 2 47 980003 Washer, 3/8 Flat 9
7920005 Nut, 3/8-24 Hex Jam 1 48 501380 Bearing, Block 2
8505121 Lever, Switch Left 149 486602 Plate, Stiffener 1
9485002 Switch Kit 150 483214 Base, B-1500, ABS 1
10 505120 Lever, Switch Right 151 501286 Bumper, Base, 48" Gray 1
11 920001 Nut, 10-32 Nyloc Stop 152 962162 Screw, #10 x 1/2 FHP HILO Zinc 3
12 509830 Washer, Handle Tube 1 53 502110 Clip, Bumper 3
13 503320 Flange, Strain Relief 154 962018 Screw, 3/8-16 x 2 HH Zinc 4
14 505720 Nipple, Handle 255 915001 Key, 3/16 x 2 7/8L 1
15 481310C Switch Box 156 980009 Washer, 3/8 Lock 4
16 515150 Label, Warning 1 57 962048 Screw, 3/8-16 1 1/4 HH 4
17 501210 Bumper, Handle 1 58 506980 Pulley, Motor 1
18 962003 Screw, 10-32 x 3/4 PHP 1 59 506994 Pulley, Pad 1
19 962006 Screw, 1/4-20 x 1/2 PHP SS 7 60 903005 Belt, 1500 RPM 1
503711 Grip, Handle, Gray 2 61 962073 Screw, 1/4-20 x 5/8 Soc Set 2
501501 Cap, Protective End 262 503382 Flange, Flex Pad Driver 1
21 980015 Washer, #10 External Tooth 2 63 962036 Screw, 1/4-20 x 1 FHP 6
508520 Strain Relief, Complete 164 962014 Screw, 5/16-18 x 3/4 1
502020 Clamp, Strain Relief 165 980006 Washer, 5/16 Lock 1
23 962015 Screw, 10-32 x 3/8 PHP 2 66 504471 Pad Holder Assembly 1
24 502422 Cord Assembly, 50' 167 962076 Screw, #8 x 5/8 PHP 3
25 509082 Tube, Handle 168 509780 Wheel, 4" Gray Non-Marking 2
26 504420 Hook, Cord 169 487202 Retainer, Axle 1
27 962005 Screw, 1/4-20 x 3/8 Set 1 70 507781 Shaft, Wheel 2
28 505010 Knob, Turn 1 71 980005 Washer, Wave 8
29 980007 Washer, 5/16 Flat 2 72 509820 Washer, Fiber 12
30 500880 Brace, Handle 2 73 507320 Ring, Snap 4
31 908008 Handle Cord Assembly 174 962161 Screw, 10 x 3/4 PHP HILO 2
32 502021 Clamp, Handle 1 75 508080 Strap, Bumper, 51" 1
33 962009 Bolt, 5/16-18 x 2 1/2 Carriage 1 76 962016 Screw, 10-32 x 3/8 Set 1
34 507481 Rod, Brace 177 509781 Wheel, 5" Gray Non-Marking 2
35 507310 Ring, 3/8 Snap 1
36 509920C Yoke 1Labels Not Shown:
37 507480 Rod, Yoke 1485106 Label, Handle Warning 1
38 962161 Screw, 10 x 3/4 PHP HILO 3 506318 Label, Interlock 1
39 502319 Cover, Bearing 1506340 Label, Brush Indicator 1
40 962026 Screw, 8-32 x 1/2 Type F 3
505181 Light, Brush Wear Indicator 115V 1
505182 Light, Brush Wear Indicator 220V 1
20
22
41
5

B-1500 BURNISHER MOTOR PARTS LIST
6
ITEM PART NO. DESCRIPTION QTY.
505286 Motor 115V, 1.5HP 1
505278 Motor 220V, 1.5HP 50C 1
A502919 End Bell - Motor LOWER 1
B500417 Armature Asm.w/Bearings,115V 1
500424 Armature Asm.w/Bearings, 220V 1
902012 Bearing, Motor Lower 1
CField & Shell Assembly 1
D902003 Bearing, Motor Top 1
E500903 Carbon Brush, Motor 115V 4
510901 Carbon Brush, Motor 220V 4
F507322 Brush Ring Asm. Complete, 115V 1
507326 Brush Ring Asm. Complete, 220V 1
GEnd Bell - Motor TOP 1
I960018 Bolt, Motor Thru 4
J911048 Rectifier, 115V 1
911081 Rectifier, 220V 1
K908024 Cord Assembly, Motor 1

B-1500 BURNISHER WIRING DIAGRAM
7

WARRANTY POLICY
BURNISHER, MODEL B-1500, ABS BASE
The Pacic Floorcare B-1500 Burnisher has been manufactured, tested and inspected in accordance with specic engineering
requirements and is WARRANTED to be free from defects in workmanship and materials as follows:
Eighteen (18) months parts, One (1) year labor - DC Motors (except recer and carbon brushes)
One (1) year parts and labor – All other components unless excluded below.
This warranty extends to the original user/purchaser and only when used, operated and maintained in accordance with Pacic
Operang and Maintenance instrucons.
This warranty does not apply to the following wear parts and accessories of the machine including:
Part Number
502422
509780
509781
503711
501286
903005
500903
Nor does it apply to damage or failure caused by improper use, abuse or neglect. Warranty credit or replacement of return
parts including motors, etc., is subject to incoming inspecon of those items.
To secure repair under this warranty, the following procedure should be taken:
• The inoperave machine or warranted parts must be delivered to the authorized dealer with shipping and delivery charges
prepaid. If unable to locate the Dealer, you may contact Pacic at the address listed herein for the locaon of the nearest
Pacic repair center or agent or for other instrucons pertaining to your warranty diculty.
• Upon compliance with the above warranty procedure, all warranted repairs would be completed at no addional charge
or cost to the user.
• Only Pacic or its authorized dealers and agents may make no charge warranty repairs on this product. All others do so
at their own risk.
This warranty limits Pacic liability to the repair of the product and/or warranted parts replacement and does not include
incidental or consequenal damages arising from the use of a Pacic machine whether defecve or not.
This warranty is in lieu of all other expressed or implied warranes and is extended to the original purchaser/user.
2259 S. SHERIDAN DRIVE
MUSKEGON, MICHIGAN 49442-6252
800-968-1332
FAX [phone]
10/12
Part Name
Cord Assembly
Wheel, 4”
Wheel, 5”
Handle Grip, Grey
Bumper Base
Belt
Carbon Brush, 115V Motor