PackshotCreator LiveStudio User manual

LiveStudio
QuickStart
INSTALLATION GUIDE

Light stand
© Sysnext. All rights reserved.
This material is not to be interpreted as a guarantee of earnings and may not be copied, reproducved, modied, published, uploaded, posted or
distributed in any way, without PackshotCreator’s prior consent.
LiveStudio
PACKAGE COMPOSITION
LED studio light
Softbox canopy
Speed ring
Product Registration Sheet
& Quick Reference Guide
Inner diffusion
cloth
Power cable
Wireless dongle
Support rods
2x
2x

LiveStudio
SPECIFICATIONS
Email: [e-mail]
Website: http://esupport.packshot-creator.com
CONTACT INFO:
Power Consumption:
Luminous Flux:
Dimension (L x W x H):
Light:
Softbox Kit:
Light Stand: Height:
Footprint:
Total Weight:
150W
>18,000 cm
34cm x 13cm x 19cm
60cm x 90cm x 38cm
106cm to 265cm
106cm
5.4kg
Operating Voltage:
Color Temperature:
Illuminant:
LED Quantity:
Dimming Adjusting Range:
Fuse:
LED Life:
CRI:
AC 100-240V - 50/60Hz
5500k ± 200k
High-Power LED Module
Single LED Integration
10% - 100%
250V - 3A
100,000 Hours
>95

LiveStudio
HARDWARE INSTALLATION
LIGHT STAND INSTALLATION:
01 02 03
Loosen the wing knob. Push down and spread out the
legs. Re-tighten the wing knob so
the light stand can stand on its
own.
Loosen the wing knob. Remove
the spigot. Re-attach the spigot in
the vertical position.
LED LIGHT INSTALLATION:
01 02 03
Mount the LED studio light on the
light stand. Start by loosening the
screw at the base of the light.
Place the light onto
the spigot stud and tighten the
screw until the light ts securely.
To remove the safety cover and
expose the LED light, hold back the
lock knob, then rotate the safety
cover counterclockwise.

LiveStudio
HARDWARE INSTALLATION
SOFTBOX INSTALLATION 1/3:
01 02 03
Place the speed ring inside the
opening on the softbox canopy.
Make sure the socket with guiding
groove faces one corner of the
softbox canopy.
There are 4 support rods in the
package, 2 with fasteners (left) on
one end and small silver caps on
the other end. The other 2 support
rods have small silver caps on one
end (center) and large silver caps
(right) on the one end.
Insert the 4 support rods into the
speed ring, 2 facing the large silver
caps ends and 2 facing the
fasteners ends, as shown on the
picture.
Pass the 2 support rods with large
silver caps through the loop of the
softbox canopy.
Insert their small silver ends into
the pocket at the corners of the
softbox canopy.
Now, slide the fasteners from the
2 other support rods with towards
the speed ring.
04 05 06

12
(Optional): Attach the inner
diffusion cloth.
LiveStudio
HARDWARE INSTALLATION
SOFTBOX INSTALLATION 2/3:
07 08 09
Plug the fasteners into the speed
ring to secure the rod.
Pass their other ends through the
loop of the softbox canopy.
Insert their small silver ends into
the pocket at the corners of the
softbox canopy, as done for step 4
and 5..
Attach the S-type mount softbox
assembly to the light. Rotate the
speed ring counterclockwise until
it “clicks” into place. Note: Wiggle
the speed ring to make sure it is
locked onto the light
securely.
Attach the four Velcro aps around
the speed ring.
10 11

LiveStudio
HARDWARE INSTALLATION
SOFTBOX INSTALLATION 3/3:
13 14 15
Remove the two white hand screws
holding the top light panel to the
top.
Stretch and attach the outer
diffusion cover.
Use the Velcro to hold it in place.
The softbox assembly can be
rotated to vertical, horizontal, or
any desired orientation.
To do so, loose the hand screw on
the speed ring.
16 17

LiveStudio
HARDWARE INSTALLATION
HEIGHT, ANGLE AND ORIENTATION ADJUSTMENTS:
01 02
Plug one end of the power cable
into the light and the other into
a power jack.
Turn on the power.
CABLE CONNECTION:
01 02 03
Loosen the wing knob on the light
stand joints and adjust the stand
height by raising and lowering the
sections of the stand to the desired
height.
Adjust the light angle by loosening
the wing knob on the side, as
pictured. Tilt the light to the
desired angle.
Adjust the horizontal orientation
of the light by loosening the screw
then rotate. Note: Re-tighten all
knobs and screw after adjustment.

LED STUDIO LIGHT OVERVIEW:
Accessories release button
Light stand locker
Light head locker
LED
Power output icon
Wireless receiver icon
Fuse socket
Power socket
Output control knob
Set button
Power button
Umbrella socket
Live Studio
COMPONENT REPLACEMENT
FUSE REPLACEMENT:
01 02 03
Unplug the power cable. Insert a
at head screwdriver into the fuse
cover. Lift to pry the fuse cover out
ot the socket.
Pull out the cover and fuse, then
replace the blown fuse with a new
one..
Push the fuse cover back into its
socket.