PackshotCreator PackshotOne Mark II User manual

PackshotOne Mark II
QuickStart
INSTALLATION GUIDE

PackshotCreator Mini
Mark II lightbox
© Sysnext. All rights reserved.
This material is not to be interpreted as a guarantee of earnings and may not be copied, reproducved, modied, published, uploaded, posted or
distributed in any way, without PackshotCreator’s prior consent.
PackshotOne Mini Mark II
PACKAGE COMPOSITION
Product Registration Sheet
& Quick Reference Guide
1 power cable
1 USB cable
5 acrylic panels
2x
2 camera mount
sponges
Reective door
cover
Round acrylic stand
Bottom glass
2x

PackshotOne Mark II
SPECIFICATIONS
Dimension (L x W x H): 105 x 95 x 150 cm
Light Box Body: 105 x 76 x 150 cm
Back Light Panel: 105 x 17 x 150 cm
Maximum Target Size
Top Shots: 77 x 74 cm
Side Shots: 77 x 73,5 x 121 cm
Total Weight: 202 kg
Maximum Object Weight: 20 kg
Email: [e-mail]
Website: http://esupport.packshot-creator.com
CONTACT INFO:

PackshotOne Mark II
SYSTEM PLACEMENT
ROLLING THE UNIT:
01 02 03
Use the #24 wrench to adjust the
leg height. Start by loosening the
top nut.
Rotate the bottom nut to make the
leg higher or lower.
Once the desired height is
obtained, tighten the top nut
against the bottom of the unit to
lock the leg into position. When all
four legs are up, the unit can easily
roll on wheels.
GUIDING THE UNIT THROUGH A DOORWAY 1/2:
01 02 03
If the doorway is less than 100 cm
wide, you will need to remove the
top and back light panel to get
the unit through the door. First,
remove the 6 white hand screws
and take o the top.
To remove the back light panel
from the main unit, keep the light
box unit on its wheels.
Lower the legs on the back light
panel to the ground.

PackshotOne Mark II
SYSTEM PLACEMENT
GUIDING THE UNIT THROUGH A DOORWAY /2:
04 05
Support the back light panel in the
vertical position while removing
the 4 white hand screws and
connecting plate on each side then
roll the main unit away to separate.
Move the light box and back
light panel through the doorway
separately.
PackshotOne Mark II
HARDWARE INSTALLATION
SWING LIGHT INSTALLATION 1/3:
01 02 03
Separate the back light panel
from the main unit (as shown in
steps 1-5 in the Guiding the Unit
Through a Doorway section).
Lay the back light panel on a piece
of foam and remove the 6 small
white hand screws.
Take off the acrylic diusion plate.

PackshotOne Mark II
HARDWARE INSTALLATION
SWING LIGHT INSTALLATION 2/3:
04 05 06
Remove the front swing lights from
inside.
Prepare the screws and washers as
pictured.
Use an Allen key to attach the
holding brackets on each front
corner as pictured.
Place the light panel that has a
sticker “L” on the holding bracket
on the left.
Place the light panel that has a
sticker “R” on the holding bracket
on the right.
Use the black hand screw and at
washer to connect the light panel
to the holding bracket.
07 08 09

ACRYLIC PANEL INSTALLATION 1/2:
PackshotOne Mark II
HARDWARE INSTALLATION
SWING LIGHT INSTALLATION 3/3:
10 11 12
Attach the diusion cover. Plug the swing lights into the main
system then rotate the external
ring to tighten.
Re-attach the back light panel to
the light box.
Five acrylic panels came with the
system – two large (all solid) and
three small (two solid and one with
an opening). Choose which two
panels to use. Slide in the panels
from the front.
f you use the short one with the
opening, place it on the side with
the door for convenient side
loading. Note: When inserting, be
sure they go through the holding
bracket at the top.
If you want to use the large panels,
remove the small white hand screws
01 02 03

Remove also the related xing
blocks holding the middle glass.
Slide out the middle glass. Slide in the large panels from the
front.
04 05 06
01 02 03
Remove the 2 white hand screws
on the frame of the top light panel.
Insert the 2 hanging screws under
the top through the 2 holes on the
frame of the top light panel. Slide
the top light panel to the right with
caution.
Remove the 2 front light columns.
PackshotOne Mark II
HARDWARE INSTALLATION
ACRYLIC PANEL INSTALLATION 2/2:
TOP LIGHT PANEL INSTALLATION 1/2:

PackshotOne Mark II
HARDWARE INSTALLATION
TOP LIGHT PANEL INSTALLATION 2/2:
04 05
String the top light power cable
through the ceiling hole.
Plug it into the port on the top of
the back light panel. Rotate the
ring to tighten.
01 02 03
Plug the connection cable “A” from
the light box into the back light
panel port “A”. Rotate the ring to
tighten.
Then, plug the connection cable
“B” into the back light panel port
“B”. Rotate the ring to tighten.
Plug the power and USB cables
into the system. Plug the other
ends into a power outlet and
computer, respectively.
CABLE CONNECTIONS 1/2:

PackshotOne Mark II
HARDWARE INSTALLATION:
CABLE CONNECTIONS 2/2:
04 05
Connect compatible camera to
your computer using the USB
cable supplied with the camera.
(Optional): Instead of batteries,
we recommend using an AC power
adaptor to power your camera.
Note: If you intend on using a
non-compatible camera, connect
the system to your camera using
the shutter release cable (not
included).
(OPTIONAL) ADDITIONAL BOTTOM GLASS INSTALLATION STEP A 1/2:
01 02 03
Follow the steps c-e in the Acrylic
Panel Installation section to remove
the middle glass.
Unscrew and remove the ap
plates on both sides of the bottom
front corner.
Remove the small white hand
screws on the holding bar.
(Follow step A if you buy PackshotOne Mark II with 50 kg load capacity in advance)
Turn the system power switch to
the “ON” position.
Note: Make sure to plug the swing
light cables into the main system
before turn the system power
switch to the “ON” position.
06

PackshotOne Mark II
HARDWARE INSTALLATION
(OPTIONAL) ADDITIONAL BOTTOM GLASS INSTALLATION STEP A 2/2:
04 05
Slide in the additional bottom
glass from the front. Note: The
additional bottom glass is heavy
and should be lied with caution.
Slide in the additional acrylic
diffusion plate from the front.
07 08
Replace the small white hand
screws on the ap plates.
Slide in the shorter acrylic panels
from the front.
06
Replace the small white hand
screws on the holding bar.

(Follow step B if you are upgrading the load capacity of PackshotOne Mark II from 20 kg to 50 kg)
PackshotOne Mark II
HARDWARE INSTALLATION
(OPTIONAL) ADDITIONAL BOTTOM GLASS INSTALLATION STEP B 1/2:
01 02
Follow the steps a-g in the Step
Ato place the bottom glass and
the acrylic diffusion plate. Remove
the white hand screws and take o
the top.
Place an acrylic tube on each hole
where the top connects to the light
box.
04 05
Put the top back on with hand
screws going thru the acrylic tubes.
Slide in the large acrylic panels
from the front.
03
There are 6 hole in total.