PackshotCreator R3 User manual

QuickStart
PackshotCreator R3
Installation Manual

PackshotCreator R3
Package Composition
PackshotCreator R3 lightbox
includes a 360 turntable
(for R3 360 models)
Light diusion panels for R3
(2 Pcs.)
System installation CD
with User Guides
USB Cable
(1 Pcs.)
Power Cable
(1 Pcs.)
Adhesive arrows (2 Pcs.)
to help you calibrate the turntable
#24 wrench
to adjust the lightbox leg height
Foam supports for camera
for top shots

PackshotCreator R3 installation
Remove the 4 screws at the top
of each corner of the lightbox.
If you wish to maximize your shooting surface, you can also remove the PackshotCreator R3 360 turntable.
Take the top wall o. Lift the Plexiglas panels up. Lift the side walls and the front
door up.
STEP 1 : REMOVING THE LIGHTBOX WALLS
A B C D
Connect the lightbox to
your computer using the
USB cable. Connect the
lightbox to the power outlet
with the power cable.
A
Use the #24 wrench to
adjust the leg height. Start
by loosening the top nut.
A
Rotate the bottom nut to
adjust the leg height. To
lock the height, x the top
nut against the bottom of
the lightbox.
B
Connect the camera to your computer through the mini-USB
cable.
To use the Open Camera mode, connect the camera to your
lightbox through the shutter release cord.
B
Launch the system on by turning the
switch on.
C
Launch the PackshotCreator R3
software.
Before starting your shooting, make
sure to calibrate your turntable. To do
so, from the software interface, click on
the 3D icon at the top right of the
screen. On the new window, click on
Turntable calibrate and follow onscreen
instructions.
D
1. GETTING STARTED
3. HARDWARE INSTALLATION
4. REMOVING THE TURNTABLE (FOR R3 360 MODELS)
l Make sure your computer meets the system requirements mentionned above.
l To install the software, insert the installation CD into your computer.
l During installation, put the required serial number and follow the instructions
until installation is complete.
2. SOFTWARE INSTALLATION
Note : Instead of using batteries for your camera, we recommend
using a AC power adaptor to power your camera.
Note : The lightbox can be put on whells so that it can be moved more easily. To do so, lift all four legs up.

© Sysnext. All rights reserved.
This material is not to be interpreted as a guarantee of earnings and may not be copied, reproduced, modified, published, uploaded, posted or distributed in any way,
without PackshotCreator’s prior consent.
Contact:
esupport.packshot-creator.com
PackshotCreator R3 installation
Note: when reinstalling the pillars, make sure to set the connector and the extra wire behind the LED lamps.
Note: to reinstall the turntable, repeat the previous steps backwards and re-calibrate the turntable.
STEP 2 : REMOVING THE BLACK PILLARS
STEP 3 : REMOVING THE TURNTABLE
Lift the
diusion
plates up to
remove them.
A
Disconnect the connector of the
LED lights.
B
A B
Remove the bottom hand screw.
C
Lift the black pillars up
to remove them and
repeat all previous steps
for each corner.
D
On the right of the turntable,
disconnect the cable that is
connected to the motor.
Loosen the horizontal white
hand screw that is on the side
of the block, on the right of the
turntable.
C
Loosen the two white hand
screws that are on the top of
the xing block.
D
Loosen the black hand screws.
E F
Slide the rst part of the block
away from the turntable.
Gently lift the turntable up to
remove it.
G
Remove all the black and white
hand screws.
Remove the rest of the block
from the lightbox.
H
I J
To remove the motor on the left
of the turntable, rst
disconnect the motor cable.
Loosen the black hand screws
on each side of the motor.
K
Remove the motor from the
lightbox.