Pakedge WX-1 User manual

QUICK START GUIDE
WX-1
802.11ac 3x3 Wireless AP
with OvrC, Plenum Rated
OvrC
Enabled

22
WX-1 features
• 802.11ac 3x3 Wireless AP with OvrC, Plenum Rated
• Built-in 3 × 3 internal antennas
• Powered by PoE+ or 12V AC power adapter (included)
• OvrC built in
• For more detailed instructions, refer to the WX-1 User Guide (
pkdge.co/wx1-ug ).
System requirements
• Windows or Mac PC with an Ethernet interface
Default settings and credentials
• Operation mode: Access Point
• IP address: If no DHCP server is detected, the default IP address will be
automatically set to 192.168.1.250.
• Username/Password (default): pakedge/pakedgea
• SSIDs (default): Pakedge2.4-1 and Pakedge5-1, security/password: WPA2-PSK/
pakedgewireless
• Guest SSIDs (default): PakedgeGuest2.4 and PakedgeGuest5, security/password:
WPA2/pakedgeguest
• Transmit power: Default is 13dBm for 2.4GHz and 18 dBm for 5 GHz.

33
Mounting options
Wall-mount bracket
A1 A2
A4A3
A6 A8A7
A5
B4 B3
B2
B1
A1 A2
A4A3
A6
A8A7
A5
B4
B3
B2 B1
Vertical mounting
Security screw tab Horizontal mounting
Security
screw tab
Mounting holes:
A: Double-gang electrical
wall box
B: Single-gang electrical
wall box, European outlet
box, U.S. 4” and 3.5”
round juction boxes

44
1 Line the two tabs on the top
of the wall bracket with the
two pockets on the back of
the access point. Slide the AP
downwards to lock it in place,
then secure it with a security
screw.

55
Spacer
To properly route the Ethernet cable to the AP, use the provided spacer.
1 Attach the wall bracket to the spacer.
2 Route the cable through the spacer.
3 Screw the assembled unit to the wall.

66
4 Attach the rectangular feet.
5 Line the two tabs on the top of the wall bracket with the two pockets on the
back of the AP. Slide the AP downwards to lock it in place, then secure it with a
security screw.
1
1
2

77
T-bar bracket
1 Place the appropriate-size T-bar
bracket into the slots on the
back of the AP and line up the
two holes on the T-bar bracket
with the two mounting points
on the back of the AP.
2 Line up the T-bar brackets with
the T-bar. Press down until
the T-bar brackets snap on.
Powering up the access point
T-bar bracket
spacers (optional)
Use 25 mm screw when using
T-bar bracket spacer
Note: Refer to the user guide for more detailed information regarding the installation
and configuration of the access point.

88
Powering up
The access point can be powered by PoE+ or by the included power adapter.
To power up the access point:
1 Connect power using a POE+ injector, a POE+ switch, or the included power
adapter.
The access point should now be up and running with its default settings. It does
not need to be configured to be functional. To make changes to the SSID and
security settings, you need to access the AP using a web browser.
Note: The PoE+ port may be considered a SELV circuit if It is not likely to require
a connection to an Ethernet network with outside plant routing (including a
campus environment) and if the ITE is to be connected only to PoE+ networks
without routing to the outside plant.

99
Logging in to the access point
To log in to the access point:
1 Connect a computer to the access point with an Ethernet cable.
2 Enter 192.168.1.250 into your web browser. You should see a login page.
3 In the username box, type pakedge. In the password box, type pakedgea, then
click Log in. The Quick Setup page opens.
4 Enter and verify a new password (required) before continuing.

1010
Notes:
• The Quick Setup page includes the most important configurations in one place, so
you can save time configuring the network.
• This page will display the first time you connect to the access point. After
connecting, you can also access this page and the Wireless settings page from
the dashboard.
Caution:
• For U.S. access point models, Country Code is locked to United States. For
international models, Country Code is a drop-down list (defaulting to GB - United
Kingdom), which must be changed to the specific country of operation.

1111
Registering your device with OvrC
OvrC gives you remote device management, real-time notifications, and intuitive
customer management, right from your computer or mobile device. Setup is plug-and-
play, with no port forwarding or DDNS address required.
To add this device to your OvrC account:
1 Connect the AP to the internet
2 Log into OvrC (www.ovrc.com)
3 Add the Device (MAC address and serial numbers needed for authentication
Router
Home
Switch
Access Point
Mobile
Apps
WANLAN
Remote Web Browser
Access
1 Gbps
Link/Act

Technical Support
For technical help:
www.pakedge.com/portal
[e-mail]
[phone]
Find details of this product’s 3-Year Limited Warranty at snapav.com/warranty ,
or request a paper copy from Customer Service at [phone]. Find
other legal resources, such as regulatory notices and patent information, at
snapav.com/legal .
6709A2533070-G 2021-02-14 TW
11734 S. Election Road
Draper, UT 84020
[phone]
www.pakedge.com
[e-mail]
©2021 Wirepath Home Systems, LLC. All Rights Reserved.
Latest version at
pkdge.co/wx1-qsg