Pakedge WA-2200-C User manual

WA-2200 Series
WA-2200, WA-2200-1,
WA-2200-C, WA-2200-C-1
802.11ac 2x2 Wave 2 Access Point
User Guide

WA-2200 Series User Guide
Contents
Regulatory notices ...................................................................................................................................................................... 1
Introduction ................................................................................................................................................................................... 3
System requirements ................................................................................................................................................................ 3
Hardware installation ................................................................................................................................................................ 3
Default settings and credentials.................................................................................................................................. 3
First-time login ............................................................................................................................................................................. 3
Configure.........................................................................................................................................................................................4
Overview ......................................................................................................................................................................................... 5
Connections ................................................................................................................................................................................... 6
Backup/Restore...........................................................................................................................................................................6
Logs ................................................................................................................................................................................................... 7
Advanced ........................................................................................................................................................................................ 7
Device Settings .................................................................................................................................................................... 7
LAN Settings .........................................................................................................................................................................8
Wireless Settings.................................................................................................................................................................8
Access Control .....................................................................................................................................................................11
Firmware..................................................................................................................................................................................11
BakPak Lite....................................................................................................................................................................................12
BakPak Lite............................................................................................................................................................................12
Reset to factory default settings .......................................................................................................................................13
Reset using the interface ...............................................................................................................................................13
Reset using the physical RESET button.................................................................................................................13

WA-2200 Series User Guide
1
Regulatory notices
FCC notice:
Any changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
FCC Class B:
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
ISED (IC):
•This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
•Ce produit répond aux spécifications techniques applicables à l'innovation, Science et
Développement économique Canada.
ISED (IC):
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.

WA-2200 Series User Guide
2
ISED (IC) 5G caution
Operations in the 5.15-5.25 Ghz band are restricted to indoor usage only.
Le fonctionnement sur la bande 5,15–5,25 Ghz est limité à une utilisation intérieure
uniquement.
FCC/ISED (IC) RF Radiation Exposure Statement: (For MPE report)
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
ISED (IC):
This device complies with the ISED radiation exposure limit set forth for an uncontrolled
environment. This device should be installed and operated with minimum distance 20cm
between the radiator & your body.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance
minimum de 20 cm entre le radiateur et votre corps.
CAN ICES-3 (B)/NMB-3(B)
EU Countries Intended for Use
The ETSI version of this device is intended for home and office (5150-5350MHz) use in
Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the
Netherlands, Portugal, Spain, Sweden, and the United Kingdom.
Control4 Corporation
11734 S Election Road
Draper, UT 84020
Email: [e-mail]
Phone: [phone]

WA-2200 Series User Guide
3
Introduction
As the central component of your wireless network, the WA-2200 802.11ac 2x2 Wave 2
Access Point provides you with high-speed, high-range wireless 8012.11ac networking. The
AP broadcasts on both the 2.4 GHz and 5 GHz bands so that select devices can choose
their preferred source of wireless connectivity, improving the overall stability, reliability,
and performance of the wireless network.
System requirements
Minimum system requirements:
•PoE switch or injector, or an AC power adapter (not included)
•A computer with an Ethernet port (for first AP setup).
Hardware installation
For hardware installation and first-time startup instructions, see the Quick Start Guide found
in the box.
Default settings and credentials
•IP address: IP will be automatically assigned by router if a DHCP server is detected or,
if no DHCP server is detected, the default IP address will be automatically set to
192.168.1.21.
•Username/Password (default): admin/password
•SSIDs (default): Pakedge_Main (5 GHz) and Pakedge_Alt (2.4 GHz)
Security/password: WPA2-PSK/pakedgewireless
•Guest SSIDs (default): PakedgeGuest2.4 and PakedgeGuest5, security/password:
WPA2/pakedgeguest
•Transmit power: 13 dBm for 2.4 GHz and 18 dBm for 5 GHz.
First-time login
The first time you log in, you are brought to the Configuretab. Here you can change your
username and password (strongly recommended), specify the device’s network name and
physical location, set the Country Code, and create or hide wireless networks.
For BakPak Lite setup instructions, see the WA-2200 Quick Start Guide.
Note: For APs sold in the U.S. and Israel, the Country Code will be preconfigured and
locked. For units sold in the rest of the world, the Country Code will be blank and must
be configured on the Configure tab during first-time setup.

WA-2200 Series User Guide
4
Configure
The Configure tab allows you to change the most common AP settings in one screen. This is
the default tab that displays after login.
•Username and Password: The first time you log in, you should change these from the
defaults (“admin” and “password”) to new credentials.
•Friendly Device Name: Give the AP a descriptive name to identify it on its web
interface screen and in BakPak.
•Device Location: Describe the physical location of the AP here.
•Device Note: Add any other notes here, such as date of installation and the technician
name.
•Time Zone: Select the time zone used for the AP’s event logs.
•Country Code: Select the country where the AP is installed.
Note: For APs sold in the U.S. and Israel, the Country Code will be preconfigured and
locked. For units that are sold in the rest of the world, the Country Code will be blank
and must be configured on the Configure tab.
•LAN Settings:
•IP Network Settings: Select the method used for assigning IP addresses
(DHCP or Static).
•IP Address: For a static IP network, enter the AP’s IP address here. For a DHCP
network, this field is read-only.
•Subnet Mask: For a static IP network, enter the AP’s subnet mask here. For a
DHCP network, this field is read-only.
•Gateway: For a static IP network, enter the AP’s Gateway address here. For a
DHCP network, this field is read-only.

WA-2200 Series User Guide
5
•DNS Settings:
•DNS Server n (server’s IP address): For a static IP network, enter up to two
DNS server IP addresses here. For a DHCP network, these fields are read-only.
•5 GHz Networks and 2.4 GHz Networks, and guest networks: Enter an SSID
(wireless network name), the authentication type to use, the WiFi password, and the
VLAN this wireless network is associated with. To view the password that’s entered,
click the eyeball icon. Select Hide to not broadcast the wireless network’s SSID.
•5 GHz Guest Network and 2.4 GHz Guest Network: Enter an SSID (wireless network
name), the authentication type to use, and the WiFi password. To view the password
that’s entered, click the eyeball icon. Select Hide to not broadcast the wireless
network’s SSID.
Overview
The Overview tab gives you a quick view of the AP’s status and critical settings.
•Notifications: System notifications at the very top of the tab. This example shows a
firmware update is available.
•Name: The device name (assigned in the Configure tab) appears here.
•IP address and MAC address: The device’s assigned IP address and unique MAC
address is shown here.
•Update Firmware: Click to open the Update Firmware screen (also accessible under
the Advanced tab). The screen also displays the firmware’s release notes.
•Software Reset: Click to restart (power cycle) the AP. It happens immediately, with
no confirmation dialog.
•Network information: Displays the number of wireless network SSIDs and the number
of channels used by each.
•Services: Displays the status of current services and settings and indicates with an
icon whether the service or setting is optimally configured.

WA-2200 Series User Guide
6
Connections
The Connections tab displays a list of connected wireless devices.
Click any column head to sort the list by that field. Available fields are:
•Hostname
•IP Address
•MAC Address
•Manufacturer
•Connected To
•Strength
•Band
•Duration
•TX/RX
Backup/Restore
The Backup/Restore tab allows you to save a configuration (backup) and restore the
configuration file.

WA-2200 Series User Guide
7
•Save Configuration: Click to save a file that contains all of this AP’s settings.
•Choose File: Click to select a saved configuration backup file to use for restoring
settings.
•Restore: Click to restore AP settings using the selected configuration backup file.
Logs
The Logs tab displays a record of system events effected by the AP. The events are
categorized and sortable by severity, timestamp, and details.
•Enable Remote Syslog to save the logs on another network. You’ll also need to
specify the remote Syslog server IP address and port.
•Download Detailed Logs: Click to download more verbose descriptions of the logged
events.
Advanced
Device Settings
Click this tile to configure LED settings, change the hostname or factory defaults, or to access
diagnostic tools.
•LEDs: Select to enable (or deselect to disable) the AP’s LEDs.
•Hostname: Enter the hostname here.
•Factory Default: Click to restore factory default settings.

WA-2200 Series User Guide
8
•Diagnostic Tools
•Ping: Select to ping a device at the indicated address.
•Traceroute: Select to run a traceroute to the indicated address.
LAN Settings
Click this tile to configure the advanced LAN port settings, such as management VLAN and
STP.
•Management VLAN: Click this toggle to enable the management VLAN.
•VLAN ID: Enter the VLAN ID the AP is associated with.
•Spanning Tree Protocol: Click this toggle to enable spanning tree protocol, then
select Priority to change the priority from its default (32768). The lower the priority,
the more likely the switch is to become the root bridge. (STP is changed in increments
of 4,096.)
Wireless Settings
Click this tile to configure advanced WiFi radio settings such as channel, power, RF scan, and
roaming features.

WA-2200 Series User Guide
9
•Wireless Settings
•Band Steering: Band steering steers 5 GHz-capable clients to that frequency.
By enabling this function, the 2.4 GHz SSID and settings will be copied to the 5
GHz band.
•RF Scan: Click to perform an automatic site survey of RF signals. The AP will
scan the channels for connected devices and will then display them in a table.
•5 GHz and 2.4 GHz Radio Settings
•Enable: Click this toggle to enable this WiFi radio band.
•Operation Mode: Both the 2.4 and the 5 GHz bands have the following
operating modes:
•Access Point: Standard mode of operation. Allows a wireless
connection to the LAN.
•WDS Root: The AP with this mode set will be the “root” device that APs
configured with WDS Repeater and WDS Bridge will connect to.
•WDS Bridge: This mode allows the AP to connect to a WDS Root
Access Point. This mode takes in the SSID broadcasted by the WDS
Root Access Point and turns it into Ethernet connectivity for client
devices.
•WDS Repeater: This mode allows the AP to connect to a WDS Root
Access Point. This setting will take the SSID broadcasted by the WDS
Root Access Point and rebroadcast it to end-user devices.
•Additional WDS Bridge and WDS Repeater settings:
•WDS Root Access Point BSSID:
•WDS Root Access Point SSID:
•Wireless Mode: Choose the setting that corresponds to the type of wireless
clients connected to your network. If you aren’t sure which type of clients will
access the wireless networks, we recommend you keep the default settings.
•Channel Width: Select the channel width for the selected channel to use. By
default, it’s set to HT 20 MHz (when using 2.4 GHz) and HT 80 MHz (when
using 5 GHz). Selecting 40 MHz on the 2.4 GHz band is possible, but not
recommended, because it will also increase the risk of impacting wireless
performance. We recommend keeping the 2.4 GHz radio set to 20 MHz and
using only channel 1, 6, or 11, because they are the only three non-overlapping
channels.
•Channel: Using the default setting (Auto), the AP automatically selects the
channel with best performance for the wireless network. To select a channel
manually, click the drop-down list and select a channel. The channel options
available depend on the Country Code selected.
•Transmit Power Level: The power depends on the distance of the devices in
your wireless network. You can use this feature to increase or decrease the
coverage area; however, we do not recommend changing this setting unless a
professional site survey is conducted. Contact your network administrator for
help.

WA-2200 Series User Guide
10
•Auto: This setting adjusts the power of the AP based on the distance to
the furthest client device.
•11 dBm (13mW) – 24 dBm (252mW): These are static power settings.
The AP will broadcast at the selected power level.
•Multicast Handling: Enable the Convert to Multicast toggle to enhance the
video/audio quality when streaming multicast content to multiple devices over
WiFi. When enabled, all the multicast traffic is converted to unicast, which
increases the delivery speed to individual devices. This feature is not
recommended if the multicast group exceeds 10 devices.
•Roaming
•Fast BSS transition (802.11r): IEEE 802.11r standard for fast roaming
reduces the authentication time when clients roam from one AP to the
other. This feature is beneficial for video streaming and voice
application. 801.11r requires WPA2/AES encryption in order to work.
Note: The roaming behavior depends on clients. To obtain full benefit
from fast roaming, wireless clients need to support 802.11r fast roaming
standard. It is not recommended to enable both band steering and fast
roaming features, which will cause some incompatibility issues.
•Client Reject RSSI: Helps with “sticky” clients that don’t reliably roam
to the closest AP. By enabling this feature, the AP continuously
monitors the station’s received signal and will de-authenticate the client
when the RSSI falls below the user-defined Client Reject RSSI Value
threshold. This setting can be configured independently on 2.4 GHz and
5 GHz radios.
•Guest Network Client IP Assignment
•DHCP: Select Internal or External.
•Starting IP Address: This is the beginning of the DHCP range used on the
guest network. If you have multiple APs, you can give them the same DHCP
range because the guest network of each AP will be independent of each
other.
•Ending IP Address: This is the last IP address available on the DHCP range.
•Subnet Mask: Select the class of the guest network. 255.255.255.0 is the
standard setting and is selected by default.
•GW IP Address: Enter the Gateway IP address
•DNS server IP address: The DNS Server IP can be set to an external DNS or to
the router’s IP address if the router provides a DNS server.

WA-2200 Series User Guide
11
Access Control
Click this tile to set up access control for connected clients.
To add a client for access control, click Add, then select the client and click Apply. The client
and its identifying information are added to the Access Control list.
Click any column head to sort the list by that field. Available fields are:
•Hostname
•IP Address
•MAC Address
•Remove
Firmware
Click this tile to access cloud and local firmware upgrades.

WA-2200 Series User Guide
12
If your firmware is up to date, this screen shows your current firmware version and provides a
link for that firmware’s release notes.
If a firmware update is available, this screen also shows the update version and the update’s
release notes. Click Upgrade to update the firmware from the cloud.
BakPak Lite
BakPak Lite is designed to provide remote cloud monitoring and configuration to the AP.
Using BakPak, you can remotely monitor and configure your customer’s AP without requiring
a truck roll or a VPN session to the customer’s network. In just a few clicks, register your AP
with your new or existing BakPak account. Registration is a two-step process where you
register the Management Agent in BakPak, and then you link the management agent to an
existing site or create a new site.
BakPak Lite
The AP has BakPak Lite built in, which means it can remotely monitor other WE Series APs via
BakPak. After the AP has been enrolled in BakPak, you can access it from anywhere in the
world by using the BakPak app or the web interface at mybakpak.com.
If you see this message bar at the top of your access point’s web interface, the AP is not yet
enrolled in BakPak.
To enroll the AP in BakPak:
1. On the message bar, click Click here to enroll. You are automatically redirected to
mybakpak.com.
2. Log in with your BakPak credentials or create a new admin account. When you are
logged in, the serial number and MAC address will be automatically populated on your
BakPak account.
To log in and view a site using the web interface:
1. In a web browser, log in to mybakpak.com.
2. Under Sites, click Manage. A list of BakPak and BakPak Lite sites opens.
3. Click the site you want to access, then click the BakPak Lite device that you want to
manage. The site’s management window expands, providing the following information:
•Device information: Identifies all information about the device, including the
serial number and firmware version, and has ability to reboot the wireless
router remotely.
•SSID configuration: Configure/edit wireless information for the primary SSID
and guest networks.
•Firmware: Applies firmware updates to the device.
•Events: Displays network analytics, including a log of user events, for network
troubleshooting.

WA-2200 Series User Guide
13
Reset to factory default settings
While setting up or troubleshooting, you may need to reboot the AP or restore it to its
factory default settings.
Caution: Do not power off the AP during a factory reset.
Reset using the interface
To only restart the AP, maintaining all settings:
1. In the Overview or Connections tab, click Software Reset. The AP restarts.
To reset to factory default settings, deleting all user settings:
Caution: Performing this reset will delete all of your settings on the AP.
1. Go to the Advanced tab and click Device Settings.
2. Click Factory Default, then click Yes.
Reset using the physical RESET button
Your AP has a recessed RESET button accessible through a pinhole next to the Ethernet port
underneath the AP.
To only reboot the AP, maintaining all settings:
1. While power is connected, insert a narrow, pointed object (such as a straightened
paper clip) into the hole.
2. Press and release the button.
To reset to factory default settings, deleting all user settings:
Caution: Performing this reset will delete all of your settings on the AP.
1. While power is connected, insert a narrow, pointed object (such as a straightened
paper clip) into the hole.
2. Press and hold the button for at least ten seconds, then release it.

11734 Election Road
Draper, UT 8402045
U.S.A
Visit Us At:
www.pakedge.com
Copyright ©2018, Control4 Corporation. All rights reserved. Control4, Pakedge, Triad, and their logos are
registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries.
4Store, 4Sight, Control4 My Home, Mockupancy, and BakPak are also registered trademarks or trademarks
of Control4 Corporation. Other names and brands may be claimed as the property of their respective
owners. All specifications subject to change without notice.
200-00576-B WA-2200 UG-cert 2018-12-04 MS