Pakedge WK-2-C User manual

QUICK START GUIDE
WK-2-C
802.11ac Dual Band Access Point

22
Package contents
Please refer to the installation manual of your product.
WK-2-C
• 802.11ac Dual Band Access Point
• Built-in 3×3 internal antennas
• Powered by PoE+ (by PoE+ injector or PoE+ switch)
• 2 LAN ports for network extensions
System requirements
• Windows or Mac PC with an Ethernet interface
WK-2-C default settings
• Operation Mode: Access Point
• IP Address: IP will be automatically assigned by router if a DHCP server is detected or, if no
DHCP server is detected, the default IP address will be automatically set to 192.168.1.250.
• Username/Password: pakedge/pakedgea
• SSID: Pakedge2.4-1 and Pakedge5-1
• Power Output: High
• Security: Disabled

33
WK-2-C mounting
1 Open the release latch and press on the back of the device to swing the WAP out from the
ceiling or wall bracket, then swing the WAP down.

44
2 Using the supplied template, cut a 9.125” diameter circle
at the desired mounting location for your WK-2-C. Route
an in-wall Ethernet cable through the opening on the back
of the WK-2-C housing, then insert the WK-2-C into the
ceiling or wall.
3 Use a Phillips screwdriver to tighten
the mounting ears. Use a clockwise
rotation.
Note: Do not use excessive force when
tightening the mounting ears. This can strip
the mounting ears and render them non-
functional.

55
4 Plug the Ethernet cable into the WK-2-C, then route the cable cable as shown. (Use the
optional cable clip, if necessary.) Then, swing the WAP back into the WK-2-C housing.

66
WK-2-C installation with optional pre-construction bracket
Pre-construction bracket sold separately.
1 Place the pre-construction bracket against the bottom of the ceiling studs at the desired
mounting location.
2 Mark locations for mounting screws. Drill 1/16” pilot holes at marked locations. Secure the
pre-construction bracket to ceiling studs using the provided hardware.
3 Install sheet rock over pre-construction bracket. Make note of where the cutout on the pre-
construction bracket is when installing the drywall.
4 Cut an opening in sheet rock using the cutout on the pre-construction bracket as a guide.
Note: The Pakedge logo should be facing outwards.

77
Powering up the access point
The access point can be powered only by PoE+.
To power up the access point:
1 Connect power using a POE+ injector or a POE+ switch.
The access point should now be up and running with its default settings. It does not need to
be congured to be functional. To make changes to the SSID and security settings, you need
to access the WK-2-C using a web browser.

88
Logging in to the access point
To log in to the access point:
1 Connect a computer to the WK-2-C with an Ethernet cable.
2 Enter 192.168.1.250 into the address bar of your web browser. You should see a login page.
3 In the username box, type pakedge. In the password box, type pakedgea, then click Login.
The following page will display when logged in:
Note: If your computer is not set to the default IP scheme of the WK-2-C (192.168.1.X), you must
rst congure the TCP/IP settings on your computer to log in through a web browser.

99
Conguring the access point
In this section, you can change the SSID name by applying the security prole that was set up in
the Security Proles tab. By default, the SSID is Pakedge2.4-1 and Pakedge5-1. You will have the
option to change the Wireless Name (SSID) and add security proles by selecting the options
from the drop-down menu.
Guest network
This will allow you to set up a guest network. See the manual for further details.

Technical Support
For technical help:
www.pakedge.com/portal
[e-mail]
[phone]
For non-technical inquires:
customerser[email protected]
[phone]
For regulatory information:
www.pakedge.com/regulatory
DOC-00182-A 2016-11-03 MS
11734 S. Election Road
Draper, UT 84020
Main: [phone] Fax: [phone]
www.pakedge.com
[email protected]
©2016 Pakedge Device & Software Inc. All rights reserved.