PAL EVEN GLOW User manual

WET NICHE INSTALLATION MANUAL

2 3
WET NICHE INSTALLATION
Drilling hole in breglass and vinyl pool
Drill holes through pool wall.
The hole should be placed 12” below the water
level or 18” below the top of the pool to enable
the retractable part of the tting to be taken out of the
pool if the lamp in the pool has to be replaced.
Drill into a at, easily accessible
area of pool wall.
After the hole is cut out, clean the area around the
hole to remove rough spots and dust.
Drill
Ø 2 ⅜” or
Ø 2 ½” Holesaw
CONTENTS
PAGE
2 Guides and Warnings
3 Nicheless Installation
6 Connecting Light
7 Connecting to driver
8 Troubleshooting
8 Terms and Conditions
GUIDES AND WARNINGS
Tools Required:
Ø 2 ⅜” or Ø 2 ½” Holesaw
Drill
Silicon + caulking gun
IMPORTANT INFORMATION:
1) Ensure that the electrical system for your pool conforms with all the requirements of the National
Electrical Code (NEC) and all relevant local codes and ordinances.
2) This 12V Underwater Light must be installed in accordance with the National Electrical Code by
a Certied Electrician or a Qualied Pool Technician. NOTE: No Bonding Terminal is required on
the forming shell since the xture is an all plastic construction and complies with NEC article 680
Requirements.
3) This Underwater light is designed for use with the PCR-4 AND PCR-2D UL Listed Class 2 LED Driver.
DO NOT CONNECT THIS 12V LIGHT DIRECT TO A 120V CIRCUIT.
The Junction Box and the low voltage transformer is located at least 4 (four) inches (10.16 cm) above
ground level or eight (8) inches(20.3 cm) above maximum water level, whichever is higher. The Junction
Box must be at least 48 inches (1.22 m) from the edge of the pool.
To be certain that the pool or spa electrical system meets all applicable requirements, the electrician
should also consult the local building department.
CANADIAN INSTALLATION 1.5” WALL FITTING
Be sure the electrical system of your pool conforms with the following requirements of the Canadian
Electrical Code (CE), and all local codes and ordinances. A licensed or certied electrician must install
the electrical system to meet or exceed those requirements before the light and (xture-housing) is
installed.

45
WET NICHE INSTALLATION
Removing and Installing Light
WET NICHE INSTALLATION
Installing Fibreglass Light
Twist light anti-
clockwise to remove
from breglass tting
Pull cable through wall. Assemble components
over cable in order:
To install light,
twist clockwise into
breglass tting
Removing Light Installing Light
1
1
2
2
Final Installation
Sealing Light to Pool Shell
Fibreglass Pool WallFibreglass Nut
½” conduit
PAL Even glow
Fibreglass Light
½” Conduit
Adaptor
1. Washer
2. Nut
Apply silicone to both
sides of pool wall.
Remove excess
silicone after tightning
back body nut.
Firmly tighten by
hand only - do not
over tighten.

CONNECTING TO LIGHT
Remove protective caps from plug and light socket by unscrewing.
Insert plug into light and secure with screw-on cap.
6
CONNECTING TO DRIVER
PAL COLOR TOUCH DRIVER
The PAL-EGF is powered by the PAL PCR-4 Class 2 LED Driver or PCR-2D that is controlled with the
PCT-1 Wireless transmitter.
Refer to PCR-4 or PCR-2D for Detailed Installation Instructions.
PCR-4 Driver
50 watts (PCR-4U-CL)
PCT-1 Transmitter
NOTE:
• Must turn off power before making DIP switch selection.
• When synching PAL lights to other OEM lights, static colors will match but color change mode
timing may vary.
• If the PAL Lights are to be used with Automation, do not use the handheld remote control and
disconnect the Wi-Fi module from the board if so equipped.
• If the Automation does not turn the PAL lights on or off and there is power to the driver, press the
S1 button one time to turn on the PAL Driver.
• Note that the PAL features of innite color selection and dimmability are not available while in
Cloned mode.
PCR-2D Driver
16 watt version (PCR-2D-16)
35 watt version (PCR-2D-35)
55 watt version (PCR-2D-60)
DIP 1 DIP 2 CLONING DIP SWITCH
SETTING
OFF ON JANDY
OFF OFF PENTAIR
ON OFF HAYWARD
ON ON PAL
1/2” PVC
Conduit
Adaptor
1/2” PVC
Conduit
1/2” PVC
Conduit
Adaptor
1/2” PVC
Conduit
Refer to PCT-1 information
sheet for full operation details
& features
7
Cloning Feature

TROUBLESHOOTING
Model: 4 Wire Evenglow Light
ISSUE REASON ACTION
Light not turning on (1) Faulty Globe. Replace Globe.
Light not turning on (2) Faulty Driver. Check Driver output under load using a
multimeter. 12volts DC.
Light not turning on (3) Cut Cable. Check the voltage at light using a
multimeter.
Light not turning on (4) Driver not connected
to GPO or switched
on.
Check Driver is connected to power,
check power indicator LED is lit on your
Driver. If still no indicator light, send
back to PAL for repair.
Light not turning on (5) Faulty LED Driver
inside control box.
Push the test button inside control box,
if lights still doesn’t turn on then send
product back to PAL.
Lights out of sync (1) Light incorrectly
wired to control box.
Check color wire sequences connecting
to control box.
Lights out of sync (2) Lights incorrectly
wired to LED lamp.
Check color sequences to LED lamp
terminal block inside the light.
TERMS AND CONDITIONS
PAL PRODUCT WARRANTY DETAILS
The PAL product is guaranteed against defects in materials and/or workmanship, under normal
domestic use for (12) twelve months.
Except as otherwise provided for by law, this guarantee becomes invalid if in the opinion of the
Company the product has been misused, abused, damaged in transit, incorrectly installed, or
connected to an electrical supply not corresponding with the products specication or a non-approved
PAL power supply.
The Company is not responsible for forwarding freight charges or losses in transit.
If any part of the product proves to be defective within the warranty period, the defective part will be
repaired or replaced, free of charge and at the discretion of PAL Lighting.
PAL Lighting shall not be liable for any loss of prots or any consequential, indirect or special loss,
damage or injury of any kind whatsoever arising directly or indirectly from PAL Lighting products. This
limitation does not apply to any liability under the Australian or New Zealand consumer legislation.
PLEASE REGISTER YOUR PRODUCT WARRANTY DETAILS ONLINE AT:
https://pallighting.com.au/product-registration/
OR You MUST retain some proof of purchase to provide evidence of the DATE of the original purchase.