Pentair INTELLIBRITE 5G LED LIGHT User manual

SELECTING A LIGHT SHOW OR FIXED COLOR (CONT’D)
FIXED COLORS
• Blue: Fixed color.
• Green: Fixed color.
• Red: Fixed color.
• White: Fixed color.
• Magenta: Fixed color.
Hold and Recall Feature: Note: When the
IntelliBrite LED light(s) are powered on, a white
light will momentarily illuminate, followed by
the selected color, unless the HOLD or RECALL
feature was previously enabled.
LIGHT SHOW MODE
• SAm Mode: Cycles through white, magenta, blue and green
colors (emulates the Pentair Water Pool and Spa SAm®
Color Changing Light).
• Party Mode: Rapid color changing building energy and excitement.
• Romance Mode: Slow color transitions creating a mesmerizing and
calming effect.
• Caribbean Mode: Transitions between a variety of blues and greens.
• American Mode: Patriotic red, white and blue transition.
• California Sunset Mode: Dramatic transitions of orange, red and
magenta tones.
• Royal Mode: Richer, deeper color tones.
INTELLIBRITE®5G LED LIGHT
FOR INTELLIBRITE POOL, SPA AND LANDSCAPE LIGHTING FIXTURES
OVERVIEW
QUICK REFERENCE GUIDE
Hold button/LED: Press this button (LED on) to capture and
save a color effect while displaying one of the light show
modes. When the button is pressed, the LED will be on,
indicating that the color effect is captured.
Recall Button/LED: Use this button (LED on) to activate the
last saved color effect. When the button is pressed, the LED
will be on, indicating that the color effect is being displayed.
CONTROLS AND
BUTTONS
The IntelliBrite Controller
controls, buttons and LEDs
are shown below:
Power ON/OFF Switch
RECALL button and LED
Dial and Color Show and
Fixed Color Selections
Door
HOLD button
and LED
PRINTED ON: 7/29/2009, 600054_ctlg pics.SLDASM
TROUBLESHOOTING
PROBLEM CAUSE/ACTION
Both of the LEDs are
flashing.
The IntelliBrite Controller has detected that the load has exceeded the maximum allowable
wattage or the output is shorted out
1. Switch of the IntelliBrite Controller OFF. Remove excessive load or short.
2. Press the IntelliBrite Controller power switch to power on the unit. Ensure that the LEDs
are no longer flashing.
The light will not illuminate.
Light does not function
properly.
Check the ground fault wiring and reset if necessary.
Check the light wiring connection to the junction box at the pool side and to the main circuit breaker.
Be sure that there is proper AC power applied to the light.
To select a color light show mode or fixed color mode, rotate the dial so that it points to the desired selection.
Hold and Recall Feature: When IntelliBrite color lights are powered on, the previously selected color will be displayed, unless
the HOLD or RECALL feature was previously enabled.
Hold button/LED: Press this button (LED on) to capture and save a color effect while displaying one of the light show modes.
When the button is pressed, the LED will be on, indicating that the color effect is captured.
Recall Button/LED: Use this button (LED on) to activate the last saved color effect. When the button is pressed, the LED will
be on, indicating that the color effect is being displayed.
The following describes how to install the IntelliBrite 5G Color LED Pool Light. The IntelliBrite 5G color LED light provides brilliant vivid
multi-colors with spectacular effects for your pool. Choose one of the seven pre-programmed color light shows or select one of the
five fixed colors to create virtually endless range of dramatic underwater lighting effects for a spectacular effect in your pool. There
are two ways to control IntelliBrite 5G Color Pool Lights; Using the IntelliBrite Controller (page 1) or using a Wall Switch (page 2).
Operating Lights Using an IntelliBrite Controller: The IntelliBrite®Controller provides complete control of IntelliBrite
underwater LED (light-emitting diode) lights, and IntelliBrite LED landscape lights. It’s easy to select a lighting feature, just dial
in any one of the pre-programmed color light shows or fixed colors. Using the Hold and Recall buttons you can also create endless
unique lighting effects. The IntelliBrite Controller can control individual or multiple IntelliBrite LED lights. Multiple IntelliBrite
LED lights can be connected via a junction box to an IntelliBrite Controller so that all lights can be switched on and off together.
IntelliBrite LED lights are fully compatible with Pentair IntelliTouch®and EasyTouch®Control Systems. For more information
about using IntelliBrite lights with IntelliTouch systems, refer to the IntelliTouch User’s Guide (P/N 520102) and the EasyTouch
User’s Guide (P/N 520584).
SELECTING A LIGHT SHOW OR FIXED COLOR
Note: When the IntelliBrite LED light(s) are powered on, a white light will momentarily illuminate, followed by the selected color, unless
the HOLD or RECALL feature was previously enabled. To select a color light show mode or fixed color mode, rotate the dial so that it
points to the desired selection. The color mode selections are described to the right starting clockwise from the 9 o’clock position:
ppw229_instructioncard_FINAL.indd 1 6/13/17 8:00 PM

1SAm Mode: Cycles through
white, magenta, blue and green
colors (emulates the Pentair
SAm®Color Changing Light).
2Party Mode: Rapid color
changing building energy and
excitement.
3Romance Mode: Slow
color transitions creating a
mesmerizing and calming
effect.
4Caribbean Mode: Transitions
between a variety of blues and
greens.
5American Mode: Patriotic red,
white and blue transition.
Number of times to cycle power (1-14)
6California Sunset Mode:
Dramatic transitions of orange,
red and magenta tones.
7Royal Mode: Richer, deeper
color tones.
8Blue: Fixed color.
9Green: Fixed color.
10 Red: Fixed color.
11 White: Fixed color.
12 Magenta: Fixed color.
13 Hold: Save the current color
effect during a color light show.
14 Recall: Activate the last saved
color effect.
Number of times to cycle power (1-14)
USINGALIGHTSWITCHTOSELECT
A LIGHT SHOW OR FIXED COLOR
Switch power on to the light. A white light will momentarily
illuminate, followed by the previously selected color. To select a
color show mode (1-7) or fixed color (8-12), turn the wall switch
off/on a specific number of times. Each number (1-12) shown
below corresponds to the number of times to power-cycle the
switch to activate a color light show or fixed color. For details
about saving color effects while in “show” modes, see “Hold” and
“Recall” feature on page 4. Example: To select California Sunset
Mode; turn the light on, then turn off and on six times. During the
off/on switching process, no illumination will occur.
When the IntelliBrite
®
5G LED Light is powered on, a
momentarily white light will illuminate, followed by the
previously selected color. Note: If power to the light is off for
more than five (5) seconds, the last color show mode or fixed
color that was saved will be displayed.
Operating Lights Using a Wall Switch (12 VAC): IntellliBrite
5G lights can be manually controlled using a standard wall-
mount light switch. Multiple IntelliBrite lights can be connected
via a junction box to a single switch so that all lights can be
switched on and off together. IntelliBrite lights can also be
automatically controlled via Pentair IntelliTouch
®
, EasyTouch
®
and SunTouch
®
Control Systems. Note: Multiple IntelliBrite
5G pool/spa lights can also be controlled using the IntelliBrite
Controller (see page 1).
TECHNICAL SUPPORT Phone: [phone] www.pentairpool.com 6/17 Part # P10-875 ©2017 Pentair Water Pool and Spa, Inc. All rights reserved.
ppw229_instructioncard_FINAL.indd 2 6/13/17 8:00 PM