Panasonic KY-B84AX User manual

®
ZY16CA611
F1111K1092
Contents
Safety Precautions ...................................... 2
Installation Location ..................................... 4
Accessories ................................................. 4
Dimensions .................................................. 5
Related Dimensional Drawings
for Custom Kitchens .................................... 6
Electrical Work ............................................. 8
Installing the Appliance ................................ 9
Post-installation Checklist .......................... 10
Installation Instructions
Induction Heating Cooktop
Model No. KY-B84AX
KY-B84AG
ENGLISH

2 3
WARNING: Failure to follow these instructions may cause
death or serious injury.
- When performing the installation, follow these instructions
properly. Improper installation may cause an electric leakage or
fire.
- Install 240 V / 40 A dedicated single phase circuit with the
earth leakage circuit breaker for the power supply. The
electrical wiring may abnormally overheat if the dedicated circuit is
not properly connected.
- Electrical work must be performed by a legally qualified
electrician. Improper wire connections may cause electric
leakages or fires.
- Ground the appliance following the electric laws. Failure to do
so may cause electric shock due to electric leakages.
CAUTION: Failure to follow these instructions may cause
injury or property damage.
- Use heat resistant materials for the countertop. However, do
not use varnished materials as they might get discolored.
The material of the countertop should have heat resistancy equal
to or exceeding “laminated thermosetting high-pressure decorative
sheets”. If the materials are not heat resistant, they may get
deformed or cause a fire.
Please fully observe the following safety precautions.
IMPORTANT
- Install the appliance in accordance with the Installation
Instructions. Otherwise, the performance of the appliance
may be affected.
- Make sure to perform a test run and explain to the customer
how to properly use the appliance.
- Proper installation is the responsibility of the installer. Any
malfunction or accident resulting from the failure to follow
Installation Instructions is not covered under guarantee.
- Hand these Installation Instructions to the customer for the
local electrical inspector’s use.
- Have a qualified electrician ground the appliance. Improper
grounding may cause an electric shock.
- Before performing the installation, definitely turn off the
circuit breaker. This can prevent electric shock.
- The power cord must be accurately connected to ensure the
integrity of the connection. Improper wire connections may
cause electric leakages or fires.
-
If the power cord is damaged, it must be replaced by the
manufacturer or its service agent or a similar qualified person in
order to avoid a hazard.
- Do not disassemble, repair or modify the appliance (the
top plate, for example). Doing so may cause the appliance to
operate abnormally and may result in danger.
- Do not step on the appliance, or drop heavy items on top of
it. Cracks in the top plate may cause overheating, malfunctions or
electric shocks.
- Do not touch high temperature parts, such as the top plate.
Safety Precautions

4 5
■Top view
■Front view
■Side view
Power cord length: approx. 1.2 m (Sheath length: approx. 0.96 m)
773
ø150ø150
ø210
ø260ø210 ø210
ø150
ø150
296
536
207 206
462
25
9
487
(measurement: mm)
Installation Location
Observe the laws concerning the installation of the appliance.
( 4 pieces )
For more details on cutout, see page 6.
Clamp
Intake vent
Exhaust vent
Cooking
zone
Min. 51 mm clearance
from cutout to rear wall
Max. 330 mm
depth of cabinets
Min. 51 mm clearance
from cutout to side wall
Cutout
Min. 762 mm clearance
from the top of the cooktop
to the bottom of the cabinets
Dimensions
83
74
57
723
Accessories

6 7
12-42
490 3
0
■Mounting hole
- Allow for a minimum of 300
mm extra space underneath
the bottom of the appliance
for air circulation.
■Side view
- To install a shelf inside the
cabinet, allow for a minimum
of 170 mm extra space in
front.
CAUTION
If this condition is not
met, do not install the
appliance.
(measurement: mm)
Dimensions
of countertop
cutout R3 1
490 3
0
727 3
0
Min.600
Building side wall
Countertop front
Min. 59 Building side wall
Building rear wall
Min. 30 for flat part
Bulge of front countertop
Rear sideFront side
Intake
Shelf
Exhaust
Min. 300 for
vertical clearance
Flow of intake and exhaust
Min.170
Min.51
Min.600
Min.51
Min.51
- Allow for a minimum of 95 mm extra space between
the countertop and the top surface of the oven for air
circulation.
Rear sideFront side
Exhaust
Flow of intake
and exhaust
Related Dimensional Drawings for Custom Kitchens
Min.95
Oven
■Side view with an oven
When installing the cooktop above an oven,
- Allow for Panasonic oven only. (HL-BD82S, as of November 2012)

8 9
Electrical Work
■Electrical requirements
■Electrical connections
- This appliance must be supplied with the proper voltage and frequency, and
connected to an individual, properly grounded branch circuit, protected by a
circuit breaker or fuse. (The rating plate is on the bottom of the appliance.)
- Means for disconnection must be incorporated in the fixed wiring in
accordance with the wiring rules.
- You must use a three-wire, single-phase A.C. 240 V, 40 A, 60 Hz electrical
system. If you connect to aluminum wiring, properly use connectors
approved for use with aluminum wiring.
- Check with the local utilities for electrical codes applied in the area.
Failure to wire the appliance according to governing codes may result in
a hazardous condition. If there are no local codes, the appliance must be
wired and fused to meet the requirements of CSA and CEC.
- After installation, show the customer where the breaker for the appliance is located.
1.Turn off power.
Turn off power at the circuit breaker or remove fuses to the appliance
branch circuit.
2.Connect the power cord.
Connect the power cord in accordance with all governing codes and
ordinances.
WARNING
Electrical work must be
performed by a legally
qualified electrician.
E L2 L1
Connect
to the
ground
terminal.
Connect
to the line
terminal.
Yellow / Green Black
Red
CAUTION
For your safety, remove
the plastic cover from
the power cord before
performing electrical work.
- In accordance with the electrical wiring rules, incorporate the earth leakage
circuit breaker in the home electrical wire.
- Follow the specification of the earth leakage circuit breaker as follows.
Rated current: 40 A, rated sensitivity current: 30 mA
■Installation of the earth leakage circuit breaker 2.Embed the main unit in the countertop cutout
while keeping it is as level as possible.
- Do not drop the unit on the countertop.
- Press down on top of the main unit to make sure
that the frame is solidly rest on the countertop.
- Make sure that the spaces between the
countertop and the under surface of the top
frame are even in the front, back, left and right.
Installing the Appliance
Correct Incorrect
WARNING
Do not disassemble the top plate. Connected wire may become loose
and cause a malfunction.
CAUTION
If the cabinet does not have an
opening in the front, the wiring needs
to be connected before the main unit
is embedded into the countertop.
1.Fasten the clamps to the main unit
(4 places on the front and back).
- Put the Cardboard A underneath the main unit to act
as a buffer in order to prevent the countertop from
getting damaged.
- Match the clamp grips with the holes on the sides of
the main unit, then slide the clamp from the right to
the left to fasten them to the main unit. Cardboard A
3.Connect the power cord
See page 8.

10
Post-installation Checklist
Upon completing installation, check and mark off the following items.
I hereby certify that installation has been completed.
Signature of installer
Checklist Checked
Appearance - Does the appliance not look like it is tilted to the front,
back, left or right?
- Is the frame not lifted up?
- Is the top plate clean?
Electrical
work
- Is the power supply a single phase, 240 V?
- Has the ground been installed?
- Has the earth leakage circuit breaker been installed?
Electrical
testing 1.Touch to turn on the main power.
- Does the main power light light up?
2.Touch the following keys to check function of each
IH heater:
- Left front heater
- Left rear heater
- Right front heater
- Right rear heater
- Make sure to turn off each IH heater and the main power switch after performing
electrical testing.
- Hand the Operating Instructions, Installation Instructions, and Warranty Certificate to
the customer.
Does "7" (heat
level display)
flash?
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
www.panasonic.ca
© Panasonic Corporation 2011 Printed in Japan