Panasonic X-Plus Series SP-DRH04 User manual

INSTRUCTION MANUAL (X-Plus Series _Ver. 1.0_131114)
H.264 Video Compression
960H Digital Video Recorder
User Guide
About this user guide
Before installing and using this unit, please read this user guide carefully.
Be sure to keep it handy for later reference.

2
Safety Precautions
Explanation of Graphical Symbols
WARNING
To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.
CAUTION
Changes or modifications not expressly approved by the manufacturer may void the user’s authority to
operate this equipment.
CAUTION
It is danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
This symbol indicates the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the
product.
This symbol indicates the presence of uninsulated ”dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

3
These precautions must be followed for safety reasons.
Warning
Do not uses if the unit emits smoke, strange sounds are heard, or odor is emitted.
Make sure the power cable is not damaged.
Make sure there is no dust accumulation on the power plug or the outlet.
Disassembly prohibited
Do not place any foreign objects inside the unit.
Do not place a container holding water or other liquids above the unit when it is connected to
power.
Do not allow the unit to get wet.
Do not use during thunder/thunder storms.
Do not place in an unstable position.
Do not expose to shock or vibration.
Do not use this unit in areas where it is exposed to the possibility of explosion.
Caution
Do not pull on the power cable when removing the power plug from the outlet.
Do not touch the power plug with wet hands.
Do not sit on.
Make sure the cables are connected properly.
Do not place heavy objects on connected units.
Never move this unit while the power is turned on.
Remove the power plug from the outlet when the unit is going to remain unused for long periods of
time.
Do not block the cooling fans or air ducts.
Do not expose to extreme temperatures or humidity changes.
Warning
Installation and servicing should be performed only by qualified and experienced personnel.
Turn off the power of the DVR when connecting cameras, audio or sensor cables.
The manufacturer is not responsible for any damage caused by improper use of the product or failure to
follow instructions for the product.
The manufacturer is not responsible for any problems caused by or resulting from the user physically
opening the DVR for examination or attempting to fix the unit. The manufacturer may not be held liable for
any issues with the unit if the warranty seal is removed.

4
Product Components
The package contains the main unit and its components as specified below. When you purchase the unit,
please check to ensure the components specified below are included.
DVR Set (4CH)
DVR Set (8 & 16CH)
DVD-RW (option for 8 & 16CH DVR))
Client Software CD
Remote Control
Battery1.5V (AAA x 2EA)
Quick Guide
HDD/DVD-RW data & power cable
HDD/DVD-RW mounting bracket &
Screw
HDD/DVD-RW fixing screw
Adaptor (DC12V 3A or 5A )
& Power Cable
Mouse
Items
4CH DVR
8/16CH DVR
HDD/DVD-RW data & power cable
1EA
2EA
HDD/DVD-RW mounting bracket
1 Set (2EA)
2Set (4EA)
HDD/DVD-RW Mounting bracket screw
4EA
8EA
HDD/DVD-RW fixing screw
4EA
8EA

5
Mounting the HDD or DVDRW (for only 8&16CH model)
1. Before installing bracket and screws onto
HDD
2. After installing bracket and screws
onto HDD.
3. Installation HDD and Bracket onto base
case (Inside)
4. Installation HDD and Bracket onto base
case (Outside)
5. After connecting power cable and data
cable with HDD
6. Whole picture after installation HDD
and DVD-RW (for only 8&16CH)

6
Basic function of the MOUSE
①: Left button: SELECT function
②:Wheel: MOVEMENT function on a drop-down menu
Compatible HDD Models
Company
Model
Size
SATA Type
RPM
BUFFER
Seagate
ST2000VM003
2 TB
SATA 3
5900 RPM
64 MB
ST2000VM002
2 TB
SATA 2
5900 RPM
64 MB
ST2000DL003(barracuda green)
2 TB
SATA 3
5900 RPM
64 MB
ST32000641AS(Barracuda XT)
2 TB
SATA 3
7200 RPM
64 MB
ST1000DM003
1 TB
SATA 3
7200 RPM
64 MB
ST31000524AS(barracuda 7200.12)
1 TB
SATA 3
7200 RPM
32 MB
ST31000322CS(pipeline)
1 TB
SATA 2
5900 RPM
8 MB
ST31000526SV(Surveillance)
1 TB
SATA 3
7200 RPM
32 MB
ST31000524AS(Barracuda)
1 TB
SATA 3
7200 RPM
32 MB
ST31000340SV(Surveillance)
1 TB
SATA 2
7200 RPM
32 MB
ST31000528AS(Barracuda)
1 TB
SATA 2
7200 RPM
32 MB
ST500DM002(barracuda)
500 GB
SATA 3
7200 RPM
16 MB
ST3500312CS(pipeline)
500 GB
SATA 2
5900 RPM
8 MB
ST3500411SV(Surveillance)
500 GB
SATA 3
7200 RPM
16 MB
ST3500413AS(Barracuda)
500 GB
SATA 3
7200 RPM
16 MB
ST3500830SCE
500 GB
SATA 2
7200 RPM
8 MB
ST3500418AS(Barracuda)
500 GB
SATA 2
7200 RPM
16 MB
ST3500410AS(Barracuda)
500 GB
SATA 2
7200 RPM
16 MB
HITACHI
HDS723020BLA642
2 TB
SATA 3
7200 RPM
64 MB
HDS722020ALA330
2 TB
SATA 2
7200 RPM
32 MB
HDS721010DLE630
1 TB
SATA 3
7200 RPM
32 MB
HDS721010KLA330
1 TB
SATA 2
7200 RPM
32 MB
HDT721010SLA360
1 TB
SATA 2
7200 RPM
16 MB
HDS721010CLA332
1 TB
SATA 2
7200 RPM
32 MB
HDS721050CLA362
500 GB
SATA 2
7200 RPM
16 MB
HDP725050GLA360
500 GB
SATA 2
7200 RPM
16 MB

7
Western
Digital
WD20EURS-63SPKY0
2 TB
SATA 2
5400 RPM
64 MB
WD5000AAKX-00ERMAO
500 GB
SATA 3
7200 RPM
16 MB
WD5000AVCS-632DY1
500 GB
SATA 2
5400 RPM
32 MB
WD10EZEX-00RKKAO
1 TB
SATA 3
7200 RPM
64 MB
WD20EARS
2 TB
SATA 2
5900 RPM
64 MB
WD20EARX(00PASB0)
2 TB
SATA 3
5900 RPM
65 MB
WD20EADS
2 TB
SATA 2
5400 RPM
32 MB
WD20EURS
2 TB
SATA 2
64 MB
WD10EURX(63FH1Y0)
1 TB
SATA 3
5400 RPM
64 MB
WD10EZRX(00A8LB0)
1 TB
SATA 3
5400 RPM
64 MB
WD10EARS(00Y5B1 Caviar Green)
1 TB
SATA 3
5400 RPM
64 MB
WD10EVDS(63U8B1)
1 TB
SATA 3
7200 RPM
32 MB
WD10EALX(229BA1)
1 TB
SATA 3
7200 RPM
32 MB
WD10EALX(009BA0)
1 TB
SATA 3
7200 RPM
32 MB
WD10EVVS
1 TB
SATA 2
5400 RPM
8 MB
WD10EACS
1 TB
SATA 2
16 MB
WD10EUCX
1 TB
SATA 3
16 MB
WD10EURS(630AB1)
1 TB
SATA 2
5900 RPM
64 MB
WD5000AAKX(221CA1 Caviar Blue)
500 GB
SATA 2
7200 RPM
16 MB
WD5000AAKX(001CA0)
500 GB
SATA 3
7200 RPM
16 MB
WD5000AVCS
500 GB
SATA 2
16 MB
WD5000AACS
500 GB
SATA 2
5400 RPM
16 MB
TOSHIBA
HDS723020BLE640
2 TB
SATA 3
7200 RPM
64 MB
NOTICE
The brands and models of all HDD should be the same. If the brands and models of each HDD are different
with others, the DVR may not recognize HDD.

8
Specifications
MODEL
SP-DRH04
SP-DRH08
SP-DRH16
Video
Input
Number of
Channels
4CH
(650/700TVL)
8CH
(650/700TVL)
16CH
(650/700TVL)
Signal Format
NTSC/PAL
Output
Main Monitor
VGA and HDMI (1920x1080)
Sub Monitor
CVBS or SPOT
CVBS and SPOT
Audio
Input & Output
4 Line Input & 1 Line Output
Audio Codec
G.711
Alarm
Sensor Input
4
Alarm Output
1
Serial
RS-232C
None
Yes
RS-485
Yes
Recording
Compression
H.264
Resolution
& Frame Rate
960H(960x576)
100fps
200fps
400fps
4CIF(704x576)
100fps
200fps
400fps
CIF(352x288)
100fps
200fps
400fps
Recording Quality Grade
5 Levels
Recording Mode
Continuous / Motion / Sensor / Schedule / Manual
Pre Recording
Max. 20 Minutes
Post Recording
Max. 60 Seconds
Playback
Search
Date/Time, Event, Archive, Log
Multi-Decoding
1, 4
1, 4, 8
1, 4, 9, 16
Playback Speed
x0.25, x0.5, x2, x4, x8, x16, x32, x64
Backup
Media
USB drive, External HDD, Network, DVD-R (for only 8&16CH DVR)
Format
BMP, AVI, Proprietary Format
Huge Backup
Yes (Max. 24 hours)
Storage
HDD
Capacity of 1 HDD
Up to 2TB
Up to 3TB
Internal HDDs
1
2 (1 with DVD-R)
e-SATA
None
Yes
USB
Front
1
Rear
1
User I/F
Input Method
Front Button, IR, Mouse, Keyboard Controller
Network
Interface
10/100 Base-T
10/100/1000 Base-T
Dynamic DNS
Yes (Free DDNS)
Dual Encoding for Network
Yes
Features
Digital Zoom
Yes
DLS (Day Light Saving)
Yes

9
NTP (Network Time Protocol)
Yes
S.M.A.R.T
Yes
Internal Beep
Yes
Multi-Language
Yes
e-mail Notification
Yes
Network
Access
3G/4G Mobile
iPhone / iPad / Android Phone & Tab
Web Viewer
Windows (IE, Chrome, Firefox, Safari)
PC Client
Single / Multi Client
Remote Setup and Upgrade
Yes
Power
Power Supply Voltage
DC 12V 3A
DC 12V 5A
Temperatur
e
Operation Temperature
5°C - 40°C, During storage: -10°C - +50°C
Weight
Unit Weight (Gross weight)
1.5 Kg(3 Kg)
4.1 Kg(6.2 Kg)
Dimension
Unit Dimension (W x D x H)
340 x 262 x 63mm
380 x 340 x 72mm
Please note that specifications and unit exterior design are subject to change without notification

10
Table of Contents
1. Main Features ............................................................................................................13
2. Name, Function and Connection ................................................................................14
2-1. Front Panel...................................................................................................................................14
2-2. Rear Panel...................................................................................................................................17
2-3. Remote control.............................................................................................................................19
3. Setting up the DVR.....................................................................................................20
3-1. Setup –Main Screen....................................................................................................................20
3-2. Setup –Display Mode ..................................................................................................................24
3-3. Setup –Recording Mode..............................................................................................................26
3-3-1. Recording Schedules................................................................................................................27
3-4. Setup –Device Mode...................................................................................................................28
3-4-1. ALARM-OUT.............................................................................................................................29
3-4-2 SPOT-OUT setup.......................................................................................................................29
3-4-3 Controller & PTZ Setup..............................................................................................................29
3-4-4. Motion Zone Setup....................................................................................................................30
3-5. Setup –Storage Mode..................................................................................................................31
3-6. Setup –System Mode..................................................................................................................33
3-7. Setup –SECURITY Mode............................................................................................................37
3-8. Setup –Network Mode.................................................................................................................39
3-8-1. Port, Network Audio Port and Web Port.....................................................................................40
3-8-2. Network Types ..........................................................................................................................40
3-8-2-1. DHCP.....................................................................................................................................40
3-8-2-2. STATIC...................................................................................................................................41
3-8-3. DDNS........................................................................................................................................41
3-8-4. Network Stream ........................................................................................................................41
3-9. Setup - CONFIG Mode.................................................................................................................42
3-10. Quick Setup................................................................................................................................44
3-11. Saving Setup..............................................................................................................................45
4. Live, Search and Playback.........................................................................................45
4-1. Live Viewing Screen.....................................................................................................................45
4-2. SEARCH Screen..........................................................................................................................47
4-2-1. QUICK Search ..........................................................................................................................47
4-2-2. TIME-LINE Search....................................................................................................................48
4-2-3. Event Search.............................................................................................................................49
4-2-4. Go To First Time........................................................................................................................50
4-2-5. Go To Last Time........................................................................................................................50
4-2-6. Go To Specific Time ..................................................................................................................50

11
4-2-7. Archive Search..........................................................................................................................50
4-2-8. Log Search................................................................................................................................50
4-3. Play mode....................................................................................................................................51
5. PTZ Control...................................................................................................................52
6. Back up.........................................................................................................................54
6-1. Still Image backup onto USB flash memory..................................................................................54
6-2. Video backup onto USB flash memory .........................................................................................55
6-3. Transferring still images or video from the ARCHIVE list ..............................................................55
6-4. Playback of Backup Video............................................................................................................56
7. Upgrading Firmware......................................................................................................57
8. Network access using the Exclusive network viewer, UMS single..................................61
8-1. PC requirements ..........................................................................................................................61
8-2. Installing the network viewer.........................................................................................................61
8-3. Live monitoring mode and functions. ............................................................................................62
8-4. Bi directional audio.......................................................................................................................64
8-5. Remote search mode and functions.............................................................................................64
8-6. PC System configuration..............................................................................................................67
9. Network access using the Exclusive network viewer, UMS multi ...................................70
9-1. Overview......................................................................................................................................70
9-2. Minimum PC requirements...........................................................................................................70
9-3. Installing the program...................................................................................................................70
9-4. Live Window.................................................................................................................................72
9-4-1. Main user interface...........................................................................................72
9-4-2. Control buttons.................................................................................................72
9-5. Search and Playback Window......................................................................................................73
9-5-1. Main user interface...........................................................................................73
9-5-2. Main control panel............................................................................................74
9-6. Setup of UMS Multi Client.............................................................................................................76
9-6-1. General............................................................................................................76
9-6-2. Event................................................................................................................76
9-6-3. Record .............................................................................................................77
9-6-4. OSD.................................................................................................................78
9-6-5. Language.........................................................................................................78
9-6-6. About................................................................................................................78
9-7. Remote Setup ..............................................................................................................................79
9-8. Operation .....................................................................................................................................84
9-8-1. Addition, Delete, and modify of DVR sites........................................................84
9-8-2. Connect and Disconnect..................................................................................86
9-8-3. Still-image capture during Live .........................................................................88
9-8-4. Recording video on local PC during Live..........................................................88
9-8-5. Local Playback and Remote Playback .............................................................89

12
9-8-6. AVI Backup during playback.............................................................................91
10. Network –By an web-browser viewer..........................................................................93
APPENDIX: How to connect network.................................................................................96
A. How to set IP address of the DVR and open TCP port of the router?............................................96
B. How to access DVR from Remote PC? ........................................................................................98
C. How to access DVR with iPhone?.................................................................................................101
D. How to access DVR with Android?................................................................................................102

13
1. Main Features
H.264 Video compression
Reliable file system
Spot output (Live and Event Pop-up)
HDMI Video output
4Channel audio recording
Individual channel operation
Motion detection
Automatic video input and video loss detection
Covert camera operation provides enhanced security
Built-in PTZF camera control
Easy and simple user interface
Easy scheduler
Easy software upgrade

14
Instant and convenient backup via USB flash drive, network or DVD-RW (for 8&16CH model)
Exclusive file format backup
AVI backup
Various ways of network access via Network client software, Web-viewer, CMS, UMS(Multi-site
monitoring software) and Mobile Viewer
2. Name, Function and Connection
2-1. Front Panel
The following information will help you to operate the front panel controls.
Figure 2.1.1. Front panel (SP-DRH04)
①SEQ: To start auto sequencing of the screen in full screen mode. (Toggle)
②PTZ: To control PTZ operation
③SETUP: To launch SETUP menu.
④CAPTURE: To start operations of capture a still image in live mode or backup a video data in playback mode
⑤SEARCH: To go to the search menu.
⑥REC: To start and stop manual recording.
⑦PLAY/PAUSE: To play or to pause the footage in playback mode.
⑧REW: To rewind the footage at 1x, 2x, 4x, and more speed during playback.
⑨F/REW : During playback - To move the playback position 60 seconds backward.
During pause - To move the playback position 1 frame backward.
⑩F/ADV: During playback - To move the playback position 60 seconds forward.
During pause - To move the playback position moves 1 frame forward.
⑪FF: To fast forward the footage at 1x, 2x, 4x and more speeds during playback.

15
⑫USB PORT: To connect USB Thumb drive to backup data.
⑬HDD: The indicator blinks during recording and playback.
⑭POWER: The indicator blinks when the AC adaptor is connected.
Direction, Selection & Escape buttons
ⓐPress to move up the menu in Setup mode
ⓑPress to move right or to change the values in Setup mode
ⓒPress to move down the menu in Setup mode
ⓓPress to move left or to change the values in Setup mode
ⓔTo select full screen or quad screen view in live/playback. Or to select desired menu item and to store the
setup value.
ⓕTo return to previous menu screen or to exit from playback.
Figure 2.1.2. Front panel (SP-DRH08 & DRH16)
Table2.1.1. Indication lamps
NO.
Name
Description
A
CH1~16
Indicating that the channel is being recorded.
B
HDD
Indicating that the system is accessing the hard disk.
C
ALARM
Indicating that when sensor(s) is/are triggered or motion is detected.
D
NETWORK
Indicating that when Network client connects through the network.
E
BACKUP
Indicating that USB or DVD-RW storage device is stored images or
video.
F
POWER
Indicating that the system is switched on.
Table 2.1.2. Front panel buttons
NO
Name
Description

16
1
Channel keys. For channel 10, press the 0 key. For channel 11, press
the +10 and 1 key. For channel 16, press the +10 and 6 key.
2
Press to rewind the footage in playback mode.
3
Press to select audio mode such as SINGLE and MUTE.
MUTE- All of 4 channels.
SINGLE- Highlighted channel only.
4
Jump/Step backward. In playback mode, the playback position moves
60 seconds backward.
5
Press to fast forward the footage in playback mode.
6
Press to enable/disable ALARM operation.
7
Jump/Step forward. In playback mode, the playback position moves
60 seconds forward.
8
Press to start or stop manual recording.
9
Press to go to SEARCH menu in live display mode.
10
Press to play/pause the footage in playback mode.
11
Press to enter SETUP menu.
12
Enable/disable the automatic sequence of display of channels in full
screen, quad, 9-split display mode.
13
Press to control Pan/Tilt/Zoom operations.
14
Press to capture video in jpeg format in live or playback mode.
15
◀(LEFT)
Press to move left or to change the values in Setup mode.
16
▲(UP)
Press to move up the menu in Setup mode.
17
▶(RIGHT)
Press to move right or to change the values in Setup mode.
18
▼(DOWN)
Press to move down the menu in Setup mode.
19
Press to select desired menu item or to store the setup value.
20
Press for temporary storage of the changed value or to return to the
previous menu screen.
21
USB Port
To archive still-image or video into a USB memory or upgrade
firmware with USB memory stick, connect a USB memory to the USB

17
terminal.
22
OPEN
/CLOSE
To open and close the insert tray, press the button.
23
DVD drive
To save video, insert a DVD-R media
2-2. Rear Panel
Figure 2.1.3. Rear panel (SP-DRH04)
NO
Connection
Purpose
1
VIDEO IN
4 connectors for video input. (NTSC/PAL)
2
CVBS
Video output termal or Spot out terminal
3
AUDIO IN
4 connectors for audio input.
4
AUDIO OUT
1 connector for audio output.
5
VGA OUT
Connector for VGA monitor.
6
HDMI OUT
HDMI out terminal.
7
ETHERNET
RJ-45 connector for LAN connection.
8
SENSOR IN
ALARM OUT
RS-485
4 connectors for sensor device connection.
1 connector for alarm device connection.
Provides simple On/Off switching by using relay. 0.5A/125V,
1A/30V
RS-485 control terminal
9
POWER SOCKET
Connect DC12V 3AAdaptor
10
USB Port
To archive still-image or video into a USB memory or
upgrade firmware with USB memory stick, connect a USB
memory to the USB terminal.
11
GROUND
Use for ground port
Figure 2.1.4. Rear panel (SP-DRH08)
1
2
3
4
5
6
7
8
9
10
11
1
3
2
4
5
6
7
8
9
10
11
12

18
NO
Connection
Purpose
1
VIDEO IN
8 connectors for video input. (NTSC/PAL)
2
CVBS
Video output termal
3
SPOT
Spot out terminal
4
AUDIO IN
4 connectors for audio input.
5
AUDIO OUT
1 connector for audio output.
6
VGA OUT
Connector for VGA monitor.
7
HDMI OUT
HDMI out terminal.
8
ETHERNET
RJ-45 connector for LAN connection.
9
SENSOR IN
ALARM OUT
RS-485
4 connectors for sensor device connection.
1 connector for alarm device connection.
Provides simple On/Off switching by using relay. 0.5A/125V,
1A/30V
RS-485 control terminal
10
POWER SOCKET
Connect DC12V 5AAdaptor
11
USB Port
To archive still-image or video into a USB memory or
upgrade firmware with USB memory stick, connect a USB
memory to the USB terminal.
12
GROUND
Use for ground port
Figure 2.1.5. Rear panel (SP-DRH16)
NO
Connection
Purpose
1
VIDEO IN
16 connectors for video input. (NTSC/PAL)
2
CVBS
Video output termal
3
SPOT
Spot out terminal
4
AUDIO IN
4 connectors for audio input.
5
AUDIO OUT
1 connector for audio output.
6
VGA OUT
Connector for VGA monitor.
7
RS-232
For engineering use only.
8
ETHERNET
RJ-45 connector for LAN connection.
1
2
3
4
5
6
7
8
9
10
11
12
13
14

19
9
SENSOR IN
4 connectors for sensor device connection.
ALARM OUT
1 connector for alarm device connection.
Provides simple On/Off switching by using relay. 0.5A/125V,
1A/30V
RS-485
RS-485 control terminal
10
POWER SOCKET
Connect DC12V 5AAdaptor
11
USB Port
To archive still-image or video into a USB memory or
upgrade firmware with USB memory stick, connect a USB
memory to the USB terminal.
12
e-SATA Port
1 connector for External SATA
13
HDMI OUT
HDMI out terminal.
14
GROUND
Use for ground port
2-3. Remote control
①ID: To set the remote control ID.
②REC: To start and stop manual recording
③SEARCH: To go to SEARCH menu.
④F/ADV:
During playback –To move the playback position 60 seconds forward .
During Pause –To move the playback position moves 1 frame forward
⑤F/REW:
During playback –To move the playback position 60 seconds back.
During Pause –To move the playback postion 1 frame back.
⑥FF: To fast forward the recording.
⑦PLAY/PAUSE: To play or to pause the recording in playback mode
⑧REW: To rewind the recording.

20
⑨ESC:
During setup –To retun to the preivous menu screen.
During Playback –To exit playback mode
System lock –To lock a system when pressing ESC button for 5 seconds.
System unlock –To unlock a system when pressing ESC button for 5 seconds.
⑩SETUP: To open the SETUP menu.
⑪Direction buttons: To move menu items or select a channel.
⑫SEQ: To start auto sequencing the screen in full screen mode. (Toggle)
⑬BACKUP: To start a backup operations in live or playback mode
⑭0~9: To select channel (1,2,3,..) or to enter a NVR ID number or use as number key.
3. Setting up the DVR
The following sections detail the initial setup of a DVR.
3-1. Setup –Main Screen
When booting a system at first, the following messages display. After initializing, select a language and set
the time.
To enter the setup menu, select a right button of the mouse or press the SETUP button on the remote
control.
Table 3.1.1. Setup menu tree