Panasonic KX-TPA60 User manual

Panasonic KX User Guide for MaxCS Page 1
Panasonic KX-TPA60 User Guide
for MaxCS 8.5
Phone Layout

Panasonic KX User Guide for MaxCS Page 2
1. LED Indicator
2. Headset port
The headsets can be used with this unit. (Not all operations with the headsets can be
guaranteed.)
For up-to-date information about headsets that have been tested with this unit, refer to the
following web sites: http://www.panasonic.net/pcc/support/sipphone/
3. Talk Key
4. Navigator Key
5. Hold/MSG Key
This key is used while on a call to put a call on hold or retrieve a call from hold. When not on a
call if you hold this button down you will be connected the your Altigen VM and be prompted
for your password.

Panasonic KX User Guide for MaxCS Page 3
6. */Silent Mode Key
While on a call this would transmit the * dtmf. When the handset is idle you can hold this key
down for two seconds to turn off the ringer. To turn the ringer back on hold this key again for
two seconds.
7. Line Key
This key will display the line/ extension number assigned to your handset.
8. Receiver
All non-speaker phone audio will come from this source.
9. Display
This is where you will see the battery status, signal strength, and Incoming caller ID. There may
be more data displayed here depending on your call state.
10. Soft Keys
These keys perform different functions depending on call state of the phone. From left to right
these keys are referred in this manual as key A B or C.
11. Power/Cancel Key
12. XFER/CLR Key
This is used while on a call to xfer a call. When phone is idle it is used to clear input.
13. Function Key
This key is not supported with MaxCS.
14. Microphone
This is what is used to capture outbound audio.
15. Charge Contacts
These are what delivers power to the handset when it is on the charging cradle.

Panasonic KX User Guide for MaxCS Page 4
Making and Answering Calls
•To place a call, you may predial your extension number or trunk access code and number
you wish to dial then press the green Talk key. You may also press the Talk key first and once
you have a dial tone you may dial your desired number.
•To answer an incoming call, press the green Talk key while the handset is ringing.
•To place a call on hold, press the HOLD/MSG key.
•To pick up a call on hold, press the HOLD/MSG key.
Transferring Calls
•To Blind Transfer a call, press the XFER/CLR button while on a call. This will automatically put
the call on hold. Then dial the extension you wish to transfer to and press the XFER/CLR
button again.
Note: You cannot blind transfer to an outside number.
•To Supervise a Transferred call, press the XFER/CLR button while on a call. This will
automatically put the call on hold. Then dial the number or extension you wish to transfer to
and wait for the other party to answer. When you are ready to transfer the call, press the
XFER/CLR button again.
Answering a Call Waiting Call
Note: You must have either single or multiple call waiting set for your extension on the MaxCS
server.
•While on the first call you will see the second call in the display flashing. To switch to that
call, press the Soft Key A. Your first call will be placed on hold.
•To return to that call, press the soft key C. That will place your second call on hold and
return you to the first call. You can continue to use soft key Cto swap between the calls.
Connecting to Voicemail
While the phone is idle, press and hold the HOLD/MSG key and you will be connected to the
Altigen Voicemail. You will be prompted via the receiver to enter your voicemail password.
Conference Calling
Note: Hosting a conference call is not supported at this time.
Retrieving A Call from Line Park
To retrieve a call from line park, dial #51 followed by the line park number that the call is
parked on.

Panasonic KX User Guide for MaxCS Page 5
Note: If you have a certain set of line parks assigned to a group, then you must make
sure that those extensions are members of that line park group. You may also use
the phone book in the place of line park keys. Just add an entry in the phone book
that dials #51 and the line park number.
Feature Codes
The following feature codes are NOT supported with this device:
•#26
•#27
•#81
•#82
•#17
•#18
The following features codes will work with this device:
•#54
•#56
•#93
You may use the built-in phone book to create feature keys.