Panasonic ATTUNE II HD3 WX-CH455 User manual

Troubleshooting
Thepowerindicatorblinksred.
‐TheIDofthisproductisnotyetregistered
intheCenterModuleandawireless
connectioncannotbemade.RegisterIDin
theCenterModuleofthetarget.

Thepowerindicatorlightsred.
‐Thebatteryisalmostexhausted.Replace
thebatterywithachargedone.

Cannotturnontheheadset.
‐Thebatteryisexhausted.Replacethe
batterywithachargedone.
‐Thebatteryisnotinsertedcorrectly.
Positionthebatteryproperly.

Cannotcommunicatewithanother
headsetorthespeakerpost.
‐TheCenterModulemaybeturnedoff.Make
suretheCenterModulehaspower.Ifno
remedyexists,consultyourdealerfor
repairs.
‐TheheadsetIDisnotregisteredinthe
CenterModuleofthetarget.RegisterIDin
theCenterModuleofthetarget.
‐The[S]+[P]or[S]+[T]buttonsmayhave
beenpressedatthesametime,causingthe
extendedfunctionstostart.Turntheheadset
poweroffandthenbackon.

Cannothearortalktothespeakerpost,
butcommunicationswithotherheadsets
areworkingproperly.
‐Thevehicledetectormaybemalfunctioning
becausethedetectorisnotpluggedintothe
CenterModule,nopowerissupplied,orthe
detectingfunctionisoutoforder.Checkthat
thevehicledetectorispluggedinandhas
power.

Cannot“talk”or“page”incertainareas.
‐RadiowavescannotreachtheareaRemove
anymetalobstaclesblockingradiowaves.

Ifnoremedyexists,consultyourdealerforrepairs. 
Charging
Usethesuppliedchargingattachmentto
chargethebatterywiththebatterycharger.
Thechargingtimeisapproximately3hours
(whenchargedfromemptytofull).For
detailsontheindicatorduringcharging,
refertotheoperatinginstructionsforthe
batterycharger.

Whenthechargingattachment(accessory)is
attachedtothebatterychargerasshownin
thefigurebelow,insertthebatterywhile
matchingtheterminals
.
IncludedAccessories
PGGX1006ZAC1‐Colortips–Black
PGGX1006ZBC1‐ColorTip–Red
PGGX1006ZCC1‐ColorTip–Blue
PGGX1006ZDC1‐ColorTip–Green
PGGX1006ZEC1‐ColorTip–Yellow
2FA1CH455P‐Chargingattachment
OptionalAccessories
WX‐SB100‐Battery
(Li‐ion3.7VDC,700mAh)
WX‐Z3040A‐BatteryCharger
CONSUMABLES
PGHG1521ZAC1‐HeadPad
(AdjustmentSlidePad)
PGHG1520ZAC1‐EarPad
PGUR1108ZAC1‐Headband


PANASONICA
ATTUNE II
HD3 HEADSET
WX-CH455
CHEAT SHEET
12/17/2018r1.0


MicLEDColors 
OrangeSolid:ListeningALane
OrangeFlashing:TalkingALane
GreenSolid:ListeningBLane
GreenFlashing:TalkingBLane
ColorIDTip
Usedtoidentifydifferentfunctions
programedintoheadsets.
BlackisinstallbydefaultandRed,Blue,
GreenandYellowcanbeinstalledandare
includedwithheadset.
AdjustableHeadband
Headbandisadjustedtoproperfit.

TalkButtonFunctions:
Modes:
PushtoTalk:
 Clickandholdtotalk.
 Releasebuttontolisten.
TalkLock:
 Clickbuttononcetotalk.
 Clickbuttonagaintolisten.
PageButtonFunctions:
Modes:
PushtoPage:
 Clickandholdtotalk.
 Releasebuttontolisten.
TalkLock:
 Clickbuttononcetotalk.
 Clickbuttonagaintolisten.
VolumeButtonLevels
Default:VolumeLevel1
ClickVolumeButton:VolumeLevel2
ClickVolumeButton:VolumeLevel3
ClickVolumeButton:VolumeLevel4
ClickVolumeButton:VolumeLevel5
AtVolumeLevel5,headsetwilldoublebeep
andnextbuttonclick:Volume1
“S”Button
DoubleClick:
tochangelanes(wheninstalledwiththe
WX‐CC412CenterModule).
Voicepromptwillannouncewhatlanethe
headsetiscurrentlyswitchedtoo.
Clickandhold“S”andVolumeButtonsat
thesametimefor2seconds:
ThiswillactivatetheAlertfeature.
IDregistration
Beforeusingthisproduct,theunitIDmustbe
registeredintheCenterModule.AftertheID
is registered in the Center Module, wireless
communicationbetweenthisproductandthe
CenterModuleisenabled
.
1)Set the Center Module to “ID Registration” mode.
RefertotheoperatinginstructionsoftheCenter
Module.

2)Rotate the microphone boom to turn off the
power of the headset.
3)Rotate the microphone boom while holding
down the [T] and [P] buttons to turn
on the power of the headset.
●TheheadsetenterstheIDRegistrationsetting
mode.Youwillhear“RegistrationMode”andthe
powerindicatorwillblinkorange.

4)Press the [T] button*.
●Youcanhear“ConnectingCenterModuleA”and
thelaneIndicatorwillblinkorange.
●IftheCenterModuleisaWX‐CC412(A),ID
registrationforLaneBisautomaticallystarted,the
voicemessage“ConnectingCenterModuleB”is
heardfromtheearphone,andthelaneindicator
blinksgreen.
●WhentheIDRegistrationsucceeds,youwillhear
“Registrationcomplete”,“Headset
xx”(xx:IDnumberregisteredintheCenterModule),
andthepowerindicatorstops
blinkingandstayson.

5)
 When the ID registration is complete, cancel “ID
Registration” mode of the Center Module.
●Whenthisisdone,“IDRegistration”ofthis
productiscancelledandthepowerindicatorturns
green.

*WhenthisunitisconnectedtotheWX‐C3010,its
IDisregisteredintheCenter
ModuleofLaneAwhenthe[T1]buttonispressed
orintheCenterModuleofLaneB
whenthe[T2]buttonispressed.

ColorIDTip
Mi
c
LED
Ad
j
ustableHeadband
EarPad
Talk(T)Button
VolumeButton
Page(P)Button
HeadPad