Panasonic ATTUNE II HD3 User manual

Troubleshooting
Thepowerindicatorblinksred.
-The ID of this product is not yet registered
in the Center Module and a wireless
connection cannot be made. Register ID in
the Center Module of the target.

Thepowerindicatorlightsred.
-The battery is almost exhausted. Replace
the battery with a charged one.

Cannotturnontheheadset.
-The battery is exhausted. Replace the
battery with a charged one.
-The battery is not inserted correctly.
Position the battery properly.

Cannotcommunicatewithanother
headsetorthecustomerattheorder
post.
-The Center Module may be turned off. Turn
on the power switch of the Center
Module. If no remedy exists, consult your
dealer for repairs.
-The headset ID is not registered in the
Center Module of the target. Register ID in
the Center Module of the target.
-The [S] +[P] or [S] + [T] buttons may have
been pressed at the same time, causing the
extended functions to start. Turn the power
off and then back on.

Cannothearortalktothespeakpost,but
communicationswithotherheadsetsare
OK.
-The vehicle detector may be malfunctioning
because the detector is not plugged into the
Center Module, no power is supplied, or the
detecting function is out of order. Check that
the vehicle detector is plugged in and has
power. If no remedy exists, consult your
dealer for repairs.

Cannot“talk”or“page”incertainareas.
-Radio waves cannot reach the area Remove
any metal obstacles blocking radio waves.
Charging
Use the supplied charging attachment to
charge the battery with the battery charger.
The charging time is approximately 3 hours
(when charged from empty to full). For
details on the indicator during charging,
refer to the operating instructions for the
battery charger.
When the charging attachment (accessory) is
attached to the battery charger as shown in
the figure below, insert the battery while
matching the terminals.
IncludedAccessories
PGGX1006ZAC1 - Color tips – Black
PGGX1006ZBC1 - Color Tip – Red
PGGX1006ZCC1 - Color Tip – Blue
PGGX1006ZDC1 - Color Tip – Green
PGGX1006ZEC1 - Color Tip – Yellow
2FA1CH455P - Charging attachment
OptionalAccessories
WX-SB100 - Battery
(Li-ion 3.7 V DC, 700 mAh)
WX-Z3040A - Battery Charger
Consumables
PGHG1521ZAC1 - Head Pad
(Adjustment Slide Pad)
PGHG1520ZAC1 - Ear Pad
PGUR1108ZAC1 - Headband
PANASONIC
ATTUNEII
HD3HEADSET
CHEATSHEET
05/28/2021r2.0

MicLEDColors 
OrangeSolid: Listening A Lane
OrangeFlashing: Talking A Lane
GreenSolid: Listening B Lane
GreenFlashing: Talking B Lane
IDTag
Used to identify different functions
programed into headsets.
Black is install by default
Red, Blue, Green and Yellow can be installed
and are included with headset.
AdjustableHeadband
Headband is adjusted to proper fit.
TalkButtonFunctions:
Modes:
PushtoTalk:
 Click and hold to talk.
 Release button to listen.
TalkLock:
 Click button once to talk.
 Click button again to listen.
PageButtonFunctions:
Modes:
PushtoPage:
 Click and hold to talk.
 Release button to listen.
TalkLock:
 Click button once to talk.
 Click button again to listen.
VolumeButtonLevels
Default: Volume Level 1
ClickVolumeButton: Volume Level 2
ClickVolumeButton: Volume Level 3
ClickVolumeButton: Volume Level 4
ClickVolumeButton: Volume Level 5
At Volume Level 5, headset will double
beep and next button click: Volume 1

“S”Button 
DoubleClick:
to change lanes (when installed with the
WX-CC412 Center Module).
Voice prompt will announce what lane the
headset is currently switched too.
Clickandhold“S”andVolumeButtons
atthesametimefor2seconds:
This will activate the Alert feature.
Headsetregistration
1)SettheCenterModuleto“IDRegistration”mode.
RefertotheoperatinginstructionsoftheCenterModul

2)Rotatethemicrophoneboomtoturnoffthepower
theheadset.

3)Rotatethemicrophoneboomwhileholdingdownt
h
[T]and[P]buttonstoturn
onthepoweroftheheadset.
●TheheadsetenterstheIDRegistrationsettingmode.
Youwillhear“RegistrationMode”andthepowerindic
a
willblinkorange.

4)Pressthe[T]button*.
●Youcanhear“ConnectingCenterModuleA”andthe
laneIndicatorwillblinkorange.
●IftheCenterModuleisaWX-CC412(A),IDregistratio
n
forLaneBisautomaticallystarted,thevoicemessage
“ConnectingCenterModuleB”isheardfromthe
earphone,andthelaneindicatorblinksgreen.
●WhentheIDRegistrationsucceeds,youwillhear
“Registrationcomplete”,“Headset
xx”(xx:IDnumberregisteredintheCenterModule),an
thepowerindicatorstops
blinkingandstayson.

5)
 WhentheIDregistrationiscomplete,cancel“ID
Registration”modeoftheCenterModule.
●Whenthisisdone,“IDRegistration”ofthisproductis
cancelledandthepowerindicatorturnsgreen.

*WhenthisunitisconnectedtotheWX-C3010,itsIDi
s
registeredintheCenterModuleofLaneAwhenthe[T
1
buttonispressedorintheCenterModuleofLaneB
whenthe[T2]buttonispressed.
CenterModuleSearch
1)Rotatethemicrophoneboomtoturnoffthepower
theheadset.

2)Rotatethemicrophoneboomwhileholdingdownt
h
[VOL]and[P]buttonstoturnonthepowerofthe
headset.Holduntilheadsetlightsflash.
●TheheadsetwillsearchuntilitfindsaCenterModule
thatithasalreadyregisteredwith.Theheadsetwillthe
n
rebootitselfandannounceheadsetnumber.
IDTag
Mi
c
LED
Ad
j
ustableHeadband
EarPad
TalkButton
VolumeButton
PageButton
HeadPad