Panasonic VL-SV71 User manual

Model No.
Installation Guide
Model Name Model No.
VL-SV71
Video Intercom System VL-SV72
Main Monitor Station
RThis guide is for use with the above 4 models.
Door station Main monitor station
RThe Installation Guide in Indonesian can be accessed from the following site:
https://panasonic.net/cns/pcc/support/intercom/sv71
RDoor station is described as "doorphone" and Main monitor station is described as "main
monitor" in this guide.
RIn this guide, the suffix of each model number (e.g., the "BX" in "VL-SV71BX") is omitted
unless necessary.
Note to the installer
RBefore attempting to connect or operate this product, please read the label on the rear of
the doorphone and the main monitor/extension monitor.
RPlease read this guide carefully, and install the product safely and correctly by following
the instructions. Carefully read the information found in the section titled "For your
safety" in particular.
ROnly use attachments/accessories specified by the manufacturer.
RThe installation shall be carried out in accordance with all applicable installation rules.
RTo the maximum extent permitted by law, Panasonic assumes no responsibility for
injuries or property damage resulting from failures arising out of improper installation
or operation inconsistent with this document.
RAfter installation, make sure to leave this guide with the customer.
VL-MV71
VL-MV72
prj_6905-en_gb.book Page 1 Monday, April 24, 2017 6:10 PM

2
For your safety
To prevent severe injury and loss of life/
property, read this section carefully
before using the product to ensure
proper and safe operation of your
product.
Preventing fire, electric shock and
short circuits
RLeave installation work to the
dealer. Installation work requires
technique and experiences. Failure
to observe this may cause fire,
electric shock, injury, or damage to
the product. Consult the dealer.
RElectrical connection work should
be performed by certified personnel
only. Certification is required for
performing electrical connection
work. Consult your dealer.
RUse only the specified power supply
unit and AC cable.
RDo not attempt to disassemble or
modify this product. Contact an
authorised service centre for repairs.
RNever install wiring during a lightning
storm.
RDo not connect non-specified devices.
RDo not connect a power cable to a
terminal that is not specified in this
guide.
RWhen opening holes in walls for
installation or wiring, or when securing
the power cable, make sure you do not
damage existing wiring and ductwork.
RDo not make any wiring connections
when the power supply is turned on.
RDo not use the supplied power supply
unit for outdoor installations (it is for
indoor use only).
RDo not install the main monitor/
extension monitor in the following
places:
– Places where the main monitor/
extension monitor may be splashed
with water or chemicals.
– Places where there is a high
concentration of dust, or high
humidity.
RDo not perform any actions (such as
fabricating, twisting, stretching,
bundling, forcibly bending, damaging,
altering, exposing to heat sources, or
placing heavy objects on the power
cable) that may damage the power
cable. Using the product with a
damaged power cable may cause
electric shock, short circuits, or fire.
Contact an authorised service centre
for repairs.
RWhen existing chime wires are used, it
is possible that they contain AC
voltage.
Contact an authorised service centre.
Preventing electric shock
RIf the wiring is underground, do not
make any connections underground.
RIf the wiring is underground, use a
protection tube.
RIf the wiring is outdoors, use a
protection tube or a surge protector.
Preventing injury
RInstall the product securely adhering
to the instructions in this guide to
WARNING
CAUTION
prj_6905-en_gb.book Page 2 Monday, April 24, 2017 6:10 PM

3
prevent it from falling off the wall.
Avoid installing onto low-strength
walls, such as gypsum board, ALC
(autoclaved lightweight concrete),
concrete block, or veneer (less than
18 mm thick) walls.
Supplied accessories for installation
Important:
RYou will need the following additional items to install and configure the doorphone and the
main monitor/extension monitor.
Note:
RThe illustrations in the supplied manual(s) may vary slightly from the actual product.
*1 VL-SV71/VL-SV72 models only
*2 VL-SV72/VL-MV72 models only
For the doorphone*1
Screw ×2
(3.8 mm ×20 mm)
For the main monitor/extension monitor
Screw ×2
(4 mm ×16 mm)
Mounting bracket ×1
Power supply unit and related items*2
Cable binder ×
1
Power supply unit ×1
(VL-PS241)
AC cable ×1 Screw ×2
(4 mm ×
40 mm)
[Locally procured]
– Power cables (AC/DC cables)*2 and wires (for doorphone and other connections):
Prepare wires of the appropriate specification. (a"Wire type and length")
prj_6905-en_gb.book Page 3 Monday, April 24, 2017 6:10 PM

4
Precautions for installation
To avoid malfunction or communication disturbances, do not install the doorphone or the main monitor/
extension monitor in the following locations:
– Places where vibration or any other kind of impact occurs.
– Places where echoing is frequent.
– Places near a high concentration of dust, hydrogen sulphide, ammonia, sulphur, or noxious fumes.
For the doorphone
RIf a strong light is shining on the doorphone, the visitor’s face may not be distinguishable. Do not place
the doorphone in the following locations:
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will reflect off it.
– Where direct sunlight will shine on the doorphone.
RDo not place the doorphone in locations where echoing occurs, as this will cause the doorphone to
beep frequently.
RMake sure the rear of the doorphone is not subject to water.
RDepending on the installation location, condensation may form on the doorphone’s lens cover. This
may cause images to become obscured. Condensation will dissipate as the temperature rises.
For the main monitor/extension monitor
RLeave at least 20 cm of space above, below, and to the left and right sides of the main monitor/
extension monitor. Do not install on a wall that is deeply recessed.
RDo not install the main monitor/extension monitor inside a wall.
RBe sure to install the main monitor/extension monitor more than 5 m away from the doorphone.
RIn areas surrounded by a high electrical field, disturbances may occur in the main monitor’s/extension
monitor’s image or sound.
prj_6905-en_gb.book Page 4 Monday, April 24, 2017 6:10 PM

5
Wiring schematic diagram
Set up correctly according to the following wiring schematic diagram and "Wire type and length".
RFor information, such as order numbers, about optional devices that can be connected to, refer to the
"Additional/replacement accessories" section in the Operating Instructions.
APower supply
*1 When you use an additional doorphone, the maximum number of the electric locks that can be
connected to the doorphone depends on the type of doorphone. Consult your dealer for further
information.
For VL-V554 users:
– Make sure to only connect electric door locks to the S1/S2 terminals of the doorphones.
*2 Connection devices for option input (A contact) can be used when a VL-V900 and VL-V700 series
Video Intercom System for Apartment Complexes is used.
– Make sure to connect emergency terminals to the IN1/IN2 terminals.
– Make sure to connect doorbells to the IN3/IN4 terminals. A doorbell and doorphone 2 cannot be
used together.
*3 VL-SV72/VL-MV72 only
DOORPHONE 1 DOORPHONE 2
Electric
lock
Electric
lock
NP: Non-polarised
MAIN MONITOR
D1
D2
D3
D4
Ml-1
Ml-2
MO-1
MO-2
MO-3
MO-4
MO-5
MO-6
IN1
IN2
IN3
IN4
P1
P2
1
2
3
4
19
20
21
22
5
6
7
8
9
10
11
12
13
14
15
16
17
18
S1
S2
S3
S4
Ml-1
Ml-2
5
6
Ml-1
Ml-2
5
6
Ml-1
Ml-2
5
6
EXTENSION
MONITOR 1
EXTENSION
MONITOR 2
EXTENSION
MONITOR 3
Connection device
for option Input
(A contact) *2
Terminal box
(4-conductor
wiring)
PBX
11
NP
NP
NP
NP
NP
NP
NP
NP
NP
NP
You can also connect an
optional lobby station or Video
Intercom System for Apartment
Complexes. (See page 7.)
*1 *1
POWER SUPPLY UNIT
24 V DC
NP
*3
prj_6905-en_gb.book Page 5 Monday, April 24, 2017 6:10 PM

6
Wire type and length
*1 Type: Single-pair cable with outer sheath (jacket)
Conductor: Copper solid
RA certified power supply wiring has to be used with this equipment. The relevant national
installation and/or equipment regulations shall be considered. A certified power supply wiring not
lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used.
*2 When an extension monitor is used, make sure that the total wiring length from the doorphone to the
main monitor and then to the extension monitor, is within about 100 m.
*3 When using an electric lock or a connection device for option input (A contact), select a device that
meets the following guidelines:
RElectric lock connection terminal (S1/S2):
– N/O dry closure contact
– 30 V AC (1 A)/24 V DC (1 A) or lower
RConnection device for option input (A contact) terminal (IN1/IN2/IN3/IN4):
– Input method: No-voltage contact
– Open-circuit voltage between terminals: DC 7 V or less
– Detection definite time: 0.1 second or more
– Short-circuit between terminals: 5 mA or less
– Resistance value: make: 500 Ωor less, break: 15 KΩor more
Wiring run
Wire type*1
Diameter Length (Max.)
Doorphone –
Main monitor –
Extension monitor*2
ø 0.65 mm 22 AWG 100 m
ø 1.0 mm 18 AWG 130 m
ø0.5mm CAT5 50m
Main monitor –
Power supply unit
ø 0.65 mm 22 AWG 10 m
ø 1.0 mm 18 AWG 20 m
Main monitor –
Electric lock*3
ø 0.5 mm - ø 1.2 mm
(24 AWG - 17 AWG)
According to the
specifications of the
connected device.
Main monitor –
Connection device for
option input (A contact)*3
ø 0.5 mm - ø 1.2 mm
(24 AWG - 17 AWG)
According to the
specifications of the
connected device.
Main monitor –
PBX ø 0.65 mm CAT 3 or 22 AWG 100 m
prj_6905-en_gb.book Page 6 Monday, April 24, 2017 6:10 PM

7
Connecting an optional lobby station
<Be sure to perform the following to ensure proper operation>
RConnecting an optional VL-V590 lobby station
– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the lobby station.
– Connect terminal S1/S2 on the main monitor with terminal S1/S2 on the lobby station.
– After connecting to the main monitor, change the [Lobby connection] setting to [Connected devices]
using the main monitor. (→Operating Instructions of the Video Intercom System.)
RConnection for VL-V900 and VL-V700 series Video Intercom System for Apartment Complexes
– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the VL-V701 Distribution Box.
Note:
RFor information about connections, refer to the documentation of the VL-V590 or VL-V900 and VL-
V700 series.
MAIN MONITOR
D1
D2
D3
D4
Ml-1
Ml-2
MO-1
MO-2
MO-3
MO-4
MO-5
MO-6
IN1
IN2
IN3
IN4
P1
P2
1
2
3
4
19
20
21
22
5
6
7
8
9
10
11
12
13
14
15
16
17
18
S1
S2
S3
S4
<Rear view>
VL-V590 Lobby station
NP
NP: Non-polarised
NP
prj_6905-en_gb.book Page 7 Monday, April 24, 2017 6:10 PM

8
Doorphone installation position
Installation position of the doorphone and camera range
Views when the camera is facing forwards at 0° (default).
RExample: Installation height is 1450 mm (standard position).
(Units: mm)
AImage range BApprox. 66° CCentre of doorphone DApprox. 1450 EApprox. 500
FApprox. 1810 GApprox. 650 HApprox. 1160 IImage range: Approx. 960 JApprox. 87°
KApprox. 500
AImage range BApprox. 66° CCentre of doorphone DApprox. 1100 EApprox. 500
FApprox. 1690 GApprox. 710 HApprox. 980 IImage range: Approx. 1080 JApprox. 270
KApprox. 810 LApprox. 87° MApprox. 500
*1 If the camera points 15° upwards, the left or right angle is less than 7°.
Note:
The measurements and angles are for reference purposes and may vary depending on the environment.
A
C
D
E
G
H
I
J
K
A view when looking
from above
B
F
The camera angle can be adjusted using the camera angle control lever on the rear of the
doorphone (step 3, “Installing the doorphone”), so that the image range can be changed.
Side view when the camera is installed
lower than the standard position, and
facing upwards at 15°.
Top view when the camera is facing left or
right at 15° *1.
RExample: Installation height is 1100 mm.
(Units: mm)
RExample: Camera angle faces left 15°.
A
B
C
D
E
F
G
H
I
JK
LM
prj_6905-en_gb.book Page 8 Monday, April 24, 2017 6:10 PM

9
Installing the doorphone
Important:
ROn the bottom surface of the doorphone and the
mounting base, there are holes to allow water to
drain. Do not cover them up when installing.
RWhen existing wiring (such as chime wires) is
used:
– It may contain AC voltage that may cause
electric shock and/or damage the product.
– Never use the following types of wiring.
Consult a qualified technician/dealer.
RSee "Wire type and length" for information about
wiring materials.
1Remove the mounting base.
AOpen the screw cover (A).
BScrewdriver
BLoosen the mounting screw (C).
DWater drain holes
EMounting base
2Attach the mounting base (A) to the wall
securely using the wood screws (B)
(accessory).
RInstall the mounting base on a vertical flat
wall.
RBefore drilling, refer to “Precautions for
installation” for installation location.
CWire (locally procured)
D83.5 mm
*1 To prevent dew condensation, fill a hole
for wiring as much as possible.
3Adjust the camera angle using the camera
angle control lever.
ACamera angle control lever
BLeft (maximum 15°)
CRight (maximum 15°)
DUpwards (maximum 15°)
A
B
C
D
E
A
B
C
D
*1
A
B C
D
Rear view
prj_6905-en_gb.book Page 9 Monday, April 24, 2017 6:10 PM

10
Examples of camera angle
RThe angle can also be adjusted to the left or
upper left.
Important:
RWhen the camera angle is adjusted to the
upper left or upper right, the image may be
slightly distorted.
4Connect the wire, then mount the doorphone
to the mounting base.
AUnscrew the screws.
Push in the wire to the terminal connectors
(non polar), then tightly fasten the screws
(A).
BWire (connecting to the main monitor)
BMount the doorphone to the mounting
base. Fasten the screw, then close the
screw cover (C).
A– Recommended torque: 0.5 N·m
{5.1 kgf·cm}
– Maximum torque: 0.7 N·m {7.1
kgf·cm}
Facing forwards Facing upwards
Facing right Facing upper right
A
B
C
prj_6905-en_gb.book Page 10 Monday, April 24, 2017 6:10 PM