Panasonic VL-SWD275 User manual

Installation Guide
Model Name Model No.
Wireless Video Intercom System VL-SWD275
Main Monitor Station VL-MWD275
RThis guide is for use with the above 2 models.
VL-V524 VL-MWD275
Door station Main monitor station
RDoor station is described as "doorphone" and Main monitor station is described as "main
monitor" in this guide.
RIn this guide, the suffix of each model number (e.g., the "BX" in "VL-MWD275BX") is omitted
unless necessary.
Note to the installer
RBefore attempting to connect or operate this product, please read the nameplate on
the bottom or rear of the product.
RPlease read this guide carefully, and install the product safely and correctly by following
the instructions. Carefully read the information found in the section titled "For your
safety" in particular.
ROnly use attachments/accessories specified by the manufacturer.
RThe installation shall be carried out in accordance with all applicable installation rules.
R
RAfter installation, make sure to leave this guide with the customer.
To the maximum extent permitted by law, Panasonic assumes no responsibility for
injuries or property damage resulting from failures arising out of improper installation or
operation inconsistent with this document.

For your safety
To prevent severe injury or loss of life or
property, and to ensure proper and safe
operation of your product, read this
section carefully before using the
product.
WARNING
Preventing fire, electric shock and
short circuits
RLeave installation work to the
dealer. Installation work requires
technique and experiences. Failure
to observe this may cause fire,
electric shock, injury, or damage
to the product. Consult the dealer.
RElectrical connection work should
be performed by certified
personnel only. Certification is
required for performing electrical
connection work. Consult your
dealer.
RUse only the specified power supply
unit and AC cable.
RDo not attempt to disassemble or
modify this product. Contact an
authorised service centre for repairs.
RNever install wiring during a lightning
storm.
RDo not connect non-specified devices.
RDo not connect a power cable to a
terminal that is not specified in this
guide.
RWhen opening holes in walls for
installation or wiring, or when
securing the power cable, make sure
you do not damage existing wiring
and ductwork.
RDo not make any wiring connections
when the power supply is turned on.
RDo not use the supplied power supply
unit for outdoor installations (it is for
indoor use only).
RDo not install the main monitor/
extension monitor in the following
places:
– Places where the main monitor/
extension monitor may be
splashed with water or chemicals.
– Places where there is a high
concentration of dust, or high
humidity.
RDo not place objects on the power
cables and the AC adaptor. Install the
product where no one can step or trip
on the power cables and the AC
adaptor.
RDo not allow the power cables and
the AC adaptor to be excessively
pulled, bent or placed under heavy
objects.
RWhen existing wires are used, it is
possible that they contain AC voltage.
Contact an authorised service centre.
Preventing accidents and injuries
RDo not install or use the product in
health care facilities if any regulations
posted in the area instruct you not to
do so. Hospitals or health care
facilities may be using equipment that
could be sensitive to external RF
(radio frequency) energy.
RDo not install or use this product near
automatically controlled devices such
as automatic doors and fire alarms.
Radio waves emitted from this
2

product may cause such devices to
malfunction, resulting in an accident.
CAUTION
Preventing electric shock
RIf the wiring is underground, do not
make any connections underground.
RIf the wiring is underground, use a
protection tube.
RIf the wiring is outdoors, use a
protection tube or a surge protector.
Preventing injury
RInstall the product securely adhering
to the instructions in this guide to
prevent it from falling off the wall.
Avoid installing onto low-strength
walls, such as gypsum board, ALC
(autoclaved lightweight concrete),
concrete block, or veneer (less than
18 mm thick) walls.
RTo prevent serious injuries due to the
product unexpectedly falling, the
product with a wall mount feature
must be installed at a height of 2 m or
lower.
Supplied accessories for installation
For the doorphone*1
Mounting base ´ 1
Screw ´ 2
(3.8 mm ´ 20 mm)
Screw ´ 4
(4 mm ´ 12 mm)
For the main monitor/extension monitor
Screw ´ 2
(4 mm ´ 16 mm)
Mounting bracket ´ 1
Power supply unit and related items*2
Cable binder ´
1
Power supply unit ´ 1
(VL-PS241)
AC cable ´ 1 Screw ´ 2
(4 mm ´ 40 mm)
Important:
RYou will need the following additional items to install and configure the doorphone and the
main monitor/extension monitor.
[Locally procured]
– DC cable*2 and wires (for doorphone and other connections):
Prepare a cable and wires of the appropriate specification. (a"Wire type and length")
3

Note:
RThe illustrations in the supplied manual(s) may vary slightly from the actual product.
*1 VL-SWD275 models only
*2 VL-SWD275AZ/VL-MWD275AZ models only
Precautions for installation
To avoid malfunction or communication disturbances, do not install the doorphone or the main monitor/
extension monitor in the following locations:
– Places where vibration or any other kind of impact occurs.
– Places where echoing is frequent.
– Places near a high concentration of dust, hydrogen sulphide, ammonia, sulphur, or noxious fumes.
For the doorphone
RIf a strong light is shining on the doorphone, the visitor’s face may not be distinguishable. Do not place
the doorphone in the following locations:
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will reflect off it.
– Where direct sunlight will shine on the doorphone.
RDo not place the doorphone in locations where echoing occurs, as this will cause the doorphone to
beep frequently.
RDust protection/water protection is IP44.
Only when installation work specified in this guide is properly performed and appropriate water
protection treatment is performed.
RMake sure the rear of the doorphone is not subject to water.
RDepending on the installation location, condensation may form on the doorphone’s lens cover. This
may cause images to become obscured. Condensation will dissipate as the temperature rises.
For the main monitor/extension monitor
RInstall the main monitor away from electronic appliances such as TVs, radios, personal computers, air
conditioners, boiler control panels with intercom, home security equipment, wireless devices, or digital
cordless phones.
RLeave at least 20 cm of space above, below, and to the left and right sides of the main monitor/
extension monitor. Do not install on a wall that is deeply recessed.
RDo not install the main monitor/extension monitor inside a wall.
RBe sure to install the main monitor/extension monitor more than 5 m away from the doorphone.
RThe product operates in the frequency range of 1.88 GHz and 1.90 GHz with a peak transmission
power of 250 mW (max.). Refer to the "For best performance" section in the Operating Instructions.
RIn areas surrounded by a high electrical field, disturbances may occur in the main monitor’s/extension
monitor’s image or sound.
Important:
RDo not use any cleaning products that contain alcohol, polish powder, powder soap, benzine, thinner,
wax, petroleum, or boiling water. Also do not spray the product with insecticide, glass cleaner, hair
spray or wall paint. This may cause a change in colour or quality of the product.
4

Wiring schematic diagram
Set up correctly according to the following wiring schematic diagram and "Wire type and length".
RFor information, such as order numbers, about optional devices that can be connected to, refer to the
"Additional/replacement accessories" section in the Operating Instructions.
Ml-1
Ml-2
5
6
Ml-1
Ml-2
5
6
Ml-1
Ml-2
5
6
EXTENSION
MONITOR 1
EXTENSION
MONITOR 2
EXTENSION
MONITOR 3
DOORPHONE 1 DOORPHONE 2
Electric
lock
Electric
lock NP: Non-polarised
MAIN MONITOR
D1
D2
D3
D4
Ml-1
Ml-2
IN1
IN2
IN3
IN4
P1
P2
MO-1
MO-2
MO-3
MO-4
MO-5
MO-6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
S1
S2
S3
S4
19
20
21
22
Connection device
for option Input
(A contact) *2 PBX
A A
NP
NP
NP
NP
NP
NP
NP
NP
NP
NP
NP
Terminal box
(4-conductor
wiring)
You can also connect an
optional lobby station. (See
page 7.)
*1 *1
POWER SUPPLY UNIT
24 V DC
*3
Power supply
*1 When you use an additional doorphone, the maximum number of the electric locks that can be
connected to the doorphone depends on the type of doorphone. Consult your dealer for further
information.
For VL-V554 users:
– The electric lock can also be connected to the S1/S2 terminals of the doorphone.
*2 Connection devices for option input (A contact).
– Make sure to connect doorbells to the IN3/IN4 terminals. A doorbell and doorphone 2 cannot be
used together.
– When a VL-V901 and VL-V700 series Video Intercom System for Apartment Complexes is used,
emergency terminals can be used. Make sure to connect emergency terminals to the IN1/IN2
terminals.
*3 VL-SWD275AZ/VL-MWD275AZ models only
5

Wire type and length
Wiring run Wire type*1
Diameter Length (Max.)
Doorphone –
Main monitor –
Extension monitor*2
ø 0.65 mm 22 AWG 100 m
ø 1.0 mm 18 AWG 130 m
ø 0.5 mm CAT 5 50 m
Main monitor –
Power supply unit
ø 0.65 mm 22 AWG 10 m
ø 1.0 mm 18 AWG 20 m
Main monitor –
Electric lock*3
ø 0.5 mm - ø 1.2 mm
(24 AWG - 17 AWG)
According to the
specifications of the
connected device.
Main monitor –
Connection device for
option input (A contact)*3
ø 0.5 mm - ø 1.2 mm
(24 AWG - 17 AWG)
According to the
specifications of the
connected device.
Main monitor –
PBX ø 0.65 mm CAT 3 or 22 AWG 100 m
*1 Type: Single-pair cable with outer sheath (jacket)
Conductor: Copper solid
RA certified power supply wiring has to be used with this equipment. The relevant national
installation and/or equipment regulations shall be considered. A certified power supply wiring not
lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used.
*2 When an extension monitor is used, make sure that the total wiring length from the doorphone to the
main monitor and then to the extension monitor, is within about 100 m.
*3 When using an electric lock or a connection device for option input (A contact), select a device that
meets the following guidelines:
RElectric lock connection terminal (S1/S2, S3/S4):
– N/O dry closure contact
– 30 V AC (1 A)/24 V DC (1 A) or lower
RConnection device for option input (A contact) terminal (IN1/IN2/IN3/IN4):
– Input method: No-voltage contact
– Open-circuit voltage between terminals: DC 7 V or less
– Detection definite time: 0.1 second or more
– Short-circuit between terminals: 5 mA or less
– Resistance value: make: 500 W or less, break: 15 KW or more
6

n Connecting an optional lobby station
For information about connections, refer to the documentation of the lobby station to be connected.
MAIN MONITOR
D1
D2
D3
D4
Ml-1
Ml-2
IN1
IN2
IN3
IN4
P1
P2
MO-1
MO-2
MO-3
MO-4
MO-5
MO-6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
S1
S2
S3
S4
19
20
21
22
<Rear view>
Example: VL-V591 Lobby station
NP
NP: Non-polarised
NP
<Be sure to perform the following to ensure proper operation>
RConnecting an optional VL-V591 lobby station
– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the lobby station.
– Connect terminal S1/S2 on the main monitor with terminal S1/S2 on the lobby station.
– After connecting to the main monitor, change the [Lobby connection] setting to [Device connected]
using the main monitor. (®Operating Instructions of the Video Intercom System.)
Note:
RConnection for VL-V901 and VL-V700 series Video Intercom System for Apartment Complexes
– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the VL-V701 Distribution Box.
RConnection for VL-VM series/VL-VM701 Video Intercom System - Lobby station/Distributor
– Connect either terminal D1/D2 or D3/D4 on the main monitor with the terminal on the Lobby station
or VL-VM701 Distributor.
7

Doorphone installation position
Installation position of the doorphone and camera range
Views when the camera is facing forwards at 0° (default).
RExample: Installation height is 1450 mm (standard position).
(Units: mm)
A
C
D
E
G
H
I
J
K
A view when looking
from above
B
F
A Image range B Approx. 54° C Centre of doorphone D Approx. 1450 E Approx. 500
F Approx. 1740 G Approx. 510 H Approx. 1230 I Image range: Approx. 920 J Approx. 85°
K Approx. 500
The camera angle can be adjusted using the camera angle control lever on the rear of the
doorphone (step 3, “Installing the doorphone”), so that the image range can be changed.
Side view when the camera is installed
lower than the standard position, and
facing upwards at 15°.
Top view when the camera is facing left or
right at 15° *1.
RExample: Installation height is 1100 mm.
(Units: mm)
RExample: Camera angle faces left 15°.
A
B
C
D
E
F
G
H
I
JK
LM
A Image range B Approx. 54° C Centre of doorphone D Approx. 1100 E Approx. 500
F Approx. 1590 G Approx. 560 H Approx. 1030 I Image range: Approx. 1050 J Approx. 260
K Approx. 790 L Approx. 85° M Approx. 500
*1 If the camera points 15° upwards, the left or right angle is less than 5°.
Note:
RThe measurements and angles are for reference purposes and may vary depending on the
environment.
8

Installing the doorphone
Important:
ROn the bottom surface of the doorphone and the
mounting base, there are holes to allow water to
drain. Do not cover them up when installing.
RWhen existing wiring (such as chime wires) is
used:
– It may contain AC voltage that may cause
electric shock and/or damage the product.
– Never use the following types of wiring.
Consult a qualified technician/dealer.
RSee "Wire type and length" for information about
wiring materials.
1Attach the mounting base (B) (accessory) to
the wall securely.
RInstall the mounting base on a vertical flat
wall.
B
D
*1
A
C
A Screws (accessory) ´ 2
C Wire (locally procured)
D 83.5 mm
*1 To prevent dew condensation, fill a hole
for wiring as much as possible.
When using flush mount box (option):
Model No. VL-MB524
Install the flush mount box (A) in the
wall.
AC
D
E
B
B Knockout hole*1
C Approx. 90 mm D Approx. 138 mm
E Approx. 37 mm
*1 Only open the knockout holes as
required for the wiring.
2Use a slotted screwdriver (A) to push into the
holes on the bottom side of the front panel,
and remove the front panel (B) of the
doorphone.
B
A
3Adjust the camera angle using the camera
angle control lever.
Rear view
A
B C
D
A Camera angle control lever
B Left (maximum 15°)
C Right (maximum 15°)
D Upwards (maximum 15°)
9

Examples of camera angle
Facing upper leftFacing left
Facing forwards Facing upwards
RThe angle can also be adjusted to the right
or upper right.
Important:
RWhen the camera angle is adjusted to the
upper left or upper right, the image may be
slightly distorted.
4Connect the wires.
Loosen the screws. Push in the wires to the
terminal connectors (non-polar), then tighten
the screws (A).
1
A– Recommended torque: 0.5 N·m
{5.1 kgf·cm}
– Maximum torque: 0.7 N·m {7.1
kgf·cm}
5Attach the doorphone to the mounting base.
A
A Screws (accessory) ´ 4
When using flush mount box (option):
Model No. VL-MB524
Attach the doorphone to the flush mount
box.
A
A Screws (locally procured) ´ 4
R4 mm ´ 25 mm, stainless steel
(the same type of screw as the 4 mm ´
12 mm supplied accessory but with a
different length)
6Attach the front panel in the order of A ® B.
A
B
10