Panasonic EP1260-W7 User manual

©2003 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
EP1260-W7
MASSAGE LOUNGER
SPECIFICATIONS
ORDER NO.HPD0309W02C7

1 COMPONENTS IDENTIFICATION 3
2 MASSAGE RANGE (MOVEMENT RANGE OF MASSAGE
WHEELS) SHIATSU MASSAGE, SWEDISH MASSAGE,
KNEADING, VIBRATING, TAPPING A, TAPPING B, WHOLE
BACK ROLLING, REGIONAL ROLLING 5
3 TURNING ON THE POWER 6
4 REQUIRED TOOLS 7
5 ACTUAL WIRING DIAGRAM 8
6 DISPLAY METHOD OF MASSAGE BLOCK TOTAL USE TIME
AND OPERATION TIME 10
7 MOTION OF THE CLUTCH AND BELT BASED ON VARIOUS
MASSAGER OPERATIONS. 11
8 CONTROL OF THE AIR-MASSAGE OPERATION 12
9 MASSAGER UP/DOWN SENSOR GEAR ADJUSTMENT
METHOD 13
10 DISASSEMBLY AND ASSEMBLY INSTRUCTION(COSMETIC
PART AND CHAIR CONSTRUCTION) 14
11 EXAMINATION AFTER INSPECTION AND PREPAIRING 31
12 TROUBLESHOOTING 32
13 HOW TO CHECK THE PRESSURE 39
14 EXPLODED VIEW 41
15 REPLACEMENT PARTS LIST 46
CONTENTS
Page Page
2
EP1260-W7

1 COMPONENTS IDENTIFICATION
1.1. Massage lounger
3
EP1260-W7

1.2. Controller
4
EP1260-W7

Width adjustment
Approx.60 to 150mm
Intensity adjustment
Shiatsu, Swedish, Knead, vibration, Tap A, Tap B, whole
back roll, and Regional roll (from gentle to strong)
:55mm-wide adjustability where massage heads push out
toward body as intensity increases.
2 MASSAGE RANGE (MOVEMENT RANGE OF MASSAGE
WHEELS) SHIATSU MASSAGE, SWEDISH MASSAGE,
KNEADING, VIBRATING, TAPPING A, TAPPING B,
WHOLE BACK ROLLING, REGIONAL ROLLING
5
EP1260-W7

3 TURNING ON THE POWER
3.1. Turning on the power
1. Plug the power plug into the power socket.
2. Turn the lock switch to the open position.
3. Turn on the power switch on the back of the unit.
· When the operating lock switch is pointing toward ´lock´, the power switch cannot be moved to the ´on´ position.
After each use.
·Be sure to turn the power switch to ´off´.
·To prevent children from using this unit, lock the power switch by moving the operating
lock switch to the ´lock´ position.
·As a further caution, unplug the power cord from the power socket after each use.
·Always keep the key in a safe place.
Timer
When the on/off button is pushed, a timer begins to prevent overuse. After approximately 15 minutes, time expires and the
massage wheel goes into storage position.
6
EP1260-W7

4 REQUIRED TOOLS
7
EP1260-W7

5 ACTUAL WIRING DIAGRAM
5.1. Massage mechanism
8
EP1260-W7

5.2. Air ottoman
9
EP1260-W7

6 DISPLAY METHOD OF MASSAGE BLOCK TOTAL USE
TIME AND OPERATION TIME
Total use time
While pushing the + and the - intensity adjustment buttons simultaneously, turn on the power switch and continue to hold the
buttons for approximately 5 seconds. Release after the on/off LED lights up.
*When replacing the Main Circuit PCB, the use time is counted to zero because the use time is memorized in Main Circuit PCB.
*When pushing on/off button, the operation returns to normal mode.
Display method
Display it by utilizing LEDs of controller.
e.g. In the above case, (20+2
2+2 4+2 6) × 5 = (1 + 4 + 16 + 64) × 5 = 425 hours.
It is possible to indicate up to 5,115 hours.
To read the each operation function, push the following buttons after reading the total use time.
You can read the each operation function use time as the same display method of total use time.
Chart for reading each function use time
Button operation Function for reading use time LED display for confirming function
Shiatsu Shiatsu Shiatsu LED lights up
Swedish Swedish Swedish LED lights up
Kneading Kneading Kneading LED lights up
Vibration Vibration Vibration LED lights up
Tapping A Tapping A Tapping A LED lights up
Tapping B Tapping B Tapping B LED lights up
Whole back rolling Whole back rolling Whole back rolling LED lights up
Regional rolling Regional rolling Regional rolling LED lights up
10
EP1260-W7