Panasonic EP-MA10 User manual

EP-MA10 ORDER NO. HPD1008U17CE
-1 -
MASSAGE LOUNGER
EP-MA10
USA
CANADA
SPECIFICATIONS
©2010 Panasonic Electric Works Co., Ltd.
All rights reserved. Unauthorized copying
and distribution is a violation of law.

EP-MA10 ORDER NO. HPD1008U17CE
-2 -
Contents PAGE
1 SPECIFICASTIONS………………………………………………………………………………………………………………………3
2 TURNING ON THE POWER……………………………………………………………………………………………………………6
3 REQUIRED TOOLS………………………………………………………………………………………………………………………7
4 DISASSEMBLY……………………………………………………………………………………………………………………………8
5 CHECKING………………………………………………………………………………………………………………………………38
6 AIR BAG PRESSURE…………………………………………………………………………………………………………………42
7 SECRET MODE…………………………………………………………………………………………………………………………44
8 EXPLODED VIEW………………………………………………………………………………………………………………………50
9 REPLACEMENT PARTS LIST…………………………………………………………………………………………………………55

EP-MA10 ORDER NO. HPD1008U17CE
-3 -
1.COMPONENTS IDENTIFICATION
1. MASSAGE LOUNGER 1

EP-MA10 ORDER NO. HPD1008U17CE
-4 -
1.2 CONTROLLER

EP-MA10 ORDER NO. HPD1008U17CE
-5 -

EP-MA10 ORDER NO. HPD1008U17CE
-6 -
2. TURNING ON THE POWER
1. Plug the power into power socket.
2. Turn the lock switch to the open position.
3. Turn on the power switch on the power source switch box.
･When the operating lock switch is pointing toward ‘lock’, the power switch cannot be moved to the ‘on’ position.
Timer
When the on/off button is pushed, a timer begins to prevent overuse. After approximately 15 minutes, time expires and the
massage wheel goes into storage position.
After each use
･Be sure to turn the power switch to ‘off’.
･To prevent children from using this unit, lock the power switch by moving the operating lock
switch to the ‘lock’ position.
･As a further caution, unplug the power cord from the power socket after each use.

EP-MA10 ORDER NO. HPD1008U17CE
-7 -
3. REQUIRED TOOLS

EP-MA10 ORDER NO. HPD1008U17CE
-8 -
4. DISASSEMBLY
4.1. Disassembling Rear Cushion and Armrest
1.Unhook two hooks on each side by slotted
screwdriver, etc.
2.Remove two Hexagonal bolts. Unscrew four
hexagonal bolts on the Controller stand.
3.Remove Armrest by lifting up theArmrest.

EP-MA10 ORDER NO. HPD1008U17CE
-9 -
4.2. Removing the Seat
1.Proceed all the procedures of ４.1 Removing the Armrest.
2. Remove each Push-turn rivet.
3. Pull out the zippers out, cut the Cable tie, and open the
zippers which connect the Seat with the Ottoman.
4. Unscrew four screws which fit left and right Covers.
5. Unhook left and right hooks.

EP-MA10 ORDER NO. HPD1008U17CE
-10 -
6. Cut the Cable ties which connect with the right Seat
sensor cords of the Seat. Disconnect Connectors.
4.3. Removing the Ottoman
１．Execute all the procedures of 4.1 Removing the Armrest.
2. Execute all procedures of 4.2 Removing the Seat.
3. Cut five Cable ties.

EP-MA10 ORDER NO. HPD1008U17CE
-11 -
4.Remove four Push-turn rivets and remove H..
..
5.Remove the Hoses.
6.Remove the Snap pin which fixes the Ottoman
lift units.

EP-MA10 ORDER NO. HPD1008U17CE
-12 -
7.Remove the Hinge pin B, Resin bushing, and U nut
on both sides of the Ottoman, and remove the Ottoman.
4.4. Disassembly of the Ottoman
1.Proceed all the procedures of 4.3Removing the
Ottoman.
2.Remove two Screws and remove K.
3.Unzip two zippers.

EP-MA10 ORDER NO. HPD1008U17CE
-13 -
4.Remove Hoses from hole of the Cloth cover
and remove one spring and one hose in order
to remove Air ottoman cloth.
5.Remove Snap pins by pliers and remove left and
right pins in order to separate the Ottoman to both
upper and lower sides.
6. Remove each Air bag as the Figure.

EP-MA10 ORDER NO. HPD1008U17CE
-14 -
7.Remove eachAir bag as the Figure.
CAUTION
Allocate and connect Hoses as the Figure.
CAUTION
Be careful of the directions of the Sole shiatsu sheets.

EP-MA10 ORDER NO. HPD1008U17CE
-15 -
4.4. Removing the Massage mechanism block.
1. Unscrew four screws and remove the Rear cover.
CAUTION
When installing the Rear cover, do not push Rib to outside
of the Rear cover.
2. Unscrew three screws and left Rail pieces, put the jig.

EP-MA10 ORDER NO. HPD1008U17CE
-16 -
3. Unscrew three screws and remove right Rail piece.
CAUTION
Hold the Massage mechanism block so as not to make
it fall down.
4.Remove the Tool while holding the Massage mechanism
block.
CAUTION
Be careful of the Massage mechanism block.
It may fall down when the Tool is removed.
5.Holding the Guide roller, remove the Massage mechanism
block.
Otherwise, the Guide roller may pop out.

EP-MA10 ORDER NO. HPD1008U17CE
-17 -
6.Remove two Massage mechanism block cover clips
and two screws and remove the Massage mechanism
block cover
7. Remove each Lead wire and remove the Massage
mechanism block totally.
Caution in installing
Install the Guide roller spring, Washer, and Guide roller.
Install the Guider roller spring with its straight end on the
side of the Washer. Otherwise, it may lead to the abnormal
noise when in up/down operation.

EP-MA10 ORDER NO. HPD1008U17CE
-18 -
If you cannot move the Massage mechanism block up and down due to the
malfunction of the Up/down motor, move the Massage mechanism block as
follows:
1. Necessary products Air hose x 1pc (approx. 8cm)
Bit x 1pcs (approx. 8cm) Electric screwdriver x 1pc
Install the air hose on the bit.
2. Place the air hose-covered bit on the Up/down motor
rotation sensor plate, and turn on the electric screwdriver.
Caution
Operate the electric power tool at low speed
* Be careful of the wiring or sharp metal edges.

EP-MA10 ORDER NO. HPD1008U17CE
-19 -
8. Remove the Cords and screws, cut the Cable ties,
and remove Connectors and the Cover clip.
9. Turn Up/down sensor plate (counterclockwise from
upward) and move the Massage mechanism block
up (six revolutions).
10. Holding the Guide roller, remove the Massage
mechanism block. Otherwise, the Guide roller
may pop out.

EP-MA10 ORDER NO. HPD1008U17CE
-20 -
4.5. Installing the Massage Mechanism Block
1.Pushing the Massage mechanism block down,
turn Up/down sensor plate (counterclockwise
from upward). Move the Massage mechanism
block till it gears with each other.
2.Put the Massage mechanism block and install two
Rail piece sets.
CAUTION
Check if the Massage mechanism block is
horizontally installed by moving the Massage
mechanism block.
* If the Massage mechanism block is not horizontally
installed, it will lead to abnormal sounds or
malfunction