Panasonic EP1273-U1 User manual

ORDERNO.HPD0508U23C1
MASSAGELOUNGER
EP1273-U1 / EP1272-U1
SPECIFICATIONS
SPECIFICATIONS
1

2005 Matsushita ElectricWorks, Ltd. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
1. COMPONENTS IDENTIFICATION
1.1. Massage lounger
1.1.1. EP1273
2

1.1.2. EP1272
3

1.2. Controller
4

2. KNEED, SWEDISH, CONPRESSION, HAWAIIAN,
SOFT SHIATSU, TAPPING, FULL ROLLING, AND
REGIONAL ROLLING
Widthadjustment
Approx.2-7in.(6.0-18.0cm)
Intensityadjustment
Kneed, Swedish, Conpression, Hawaiian, Soft Shiatsu, Tapping, Full rolling, and Regional
rolling (fromgentle tostrong)
5

3. TURNING ON THE POWER
3.1. Turning on the power
1. Plug the power plug into the power socket.
2. Turn the lock switch to the open position.
3. Turn on the power switch on the back of the unit.
-When the operating lock switch ispointing toward 'lock', the
power switch cannot be moved to the 'on' position.
6

Aftereachuse.
-Be sure toturnthe powerswitchto'off'.
-To prevent childrenfromusing this unit, lock the powerswitch
bymoving the operating lock switchtothe 'lock'position.
-As a furthercaution, unplug the powercordfromthe power
socket aftereachuse.
-Always keepthe keyina safe place.
Timer
Whenthe on/off button is pushed, a timerbegins toprevent overuse. Afterapproximately15
minutes, time expires and the massage wheel goes intostorage position.
4. REQUIRED TOOLS
7

5. ACTUAL WIRING DIAGRAM
8

6. DISPLAY METHOD OF MASSAGE BLOCK TOTAL
USE TIME
Total use time
While pushing the + and the - speedadjustment bottons simultaneously, turnon the power
switchand continue toholdthe buttons forapproximately3 seconds. Release afterthe LED
lights up.
9

Time (hour)
LED A 5
LED B 10
LED C 20
LED D 40
LED E 80
LED F 160
LED G 320
LED H 640
LED I 1,280
LED J 2,560
Displaymethod
Displayit byutilizing LEDs of Controller.
e.g. Inthe above case, 640 (LED H) + 5 (LED A) = 645 hours.
It is possible toindicate up to5,115 hours.
To readthe eachoperation function, pushthe following buttons afterreading the total use time.
You canreadthe eachoperation function use time as the same displaymethod of total use time.
Chart forreading eachfunction use time
10

Pushthe button. LED lights. Use time
knead K knead+ swedish
compression L compression + hawaiian
swedish M massage motor
regional roll N up/downmotor
tap tap tapping motor
legmassage legmassage legairmassage
reclining up O reclining lift motor
ottomanup P ottomanlift motor
*Whenreplacing the MainCircuit PCB, the use time is countedtozerobecause the use time is
memorizedinMainCircuit PCB.
*Whenpushing on/off button, the operation returns tonormal mode.
7. DISASSEMBLY AND ASSEMBLY INSTRUCTION
(COSMETIC PART AND CHAIR CONSTRUCTION)
7.1. Removing the Head rest, Back rest cushion, Arm rest
1. Unzipthe zippers and remove the Back cushion with pillow.
2. Remove four Push-turn rivets on each sides and remove the Side
covers.
11

3. Insert ascrewdriver and unlock the lock and fall the Upper main
bodyforward.
*Becareful that the Uppermainbodymayfall forwardsuddenly.
4. Unscrew twoscrewson each outer sides, and remove the Velcro
tape on each inner sides and uncsrew one screw with washers.
After unscrewing screwson inner sides, lift the Upper mainbody
to the original position.
12

5. Pull out the Armrest.
6. Remove twolong screwswith washers (A)and one short screw
with awasher (B).
And pull out the Armrest top.
7. Unscrew one screw with washers and peel off the Velcro tape.
*When you zipthe Zippers, tuck inthe metal of the zippersunderthe cloth
13

8. Peel off the Velcro tapes (A)and remove seven Brushclips (B).
9. Unscrew five Push-turn rivets and remove the Under cover.
10. Pull out the Zipper end and the cut the Insulated tieand unzip
the Zippers.
Unscrew five Push-turn rivets (A)and unhook the Hook (B).
14

11. Insert aslotted screwdriver, etc into the hole(A)and push itto
unhook the Hook.
Unscrew aPush-turn rivet on each sides.
Then, you can remove the Seat.
7.2. Removing the Massage mechanism block
1. Insert ascrewdriver and unlock the lock and fall the Upper main
bodyforward.
*Becareful that the Uppermainbodymayfall forwardsuddenly.
*It will be convenient if you fall the Uppermainbodyforwardtoworkon the
Massage mechanism block.
*If you has removed the Seat, put it back on the Frame. Otherwise, the
Massage wheel covermayget scratched.
15

2. Unscrew four screws.
3. Unscrew the screw for the Ground wire and the screw for the
Fitting and the take off the Cover clipand remove the Connecting
cord for the MainPCB.
7.3. Removing the parts of the Massage mechanism block
1. Take off the Spring (A).
Turn the both ends of the Tapping shaft anticlockwise with
spnanners.
16

After aboltwith awasher on one side isremoved,insert abar, etc.
into the hole(B)to holdand turn the Spanner againto remove the
other bolt.
The bolts are locked with glue. When assembling them, use the
prroper glue.
Unscrew the Nut (C).
Then, you can take off the Arm block.
2. Unscrew sixscrewswith nuts (A).
Unscrew one screw with nuts (B).
Unscrew one nut (C)with abolt.
Take off the Spring (D).
Unscrew one screw with anut.
17

3. Unscrew twoscrewswith awahser and anut on the Connection
link.
Unscrew twoscrewswith awasher.
4. Take off the Tapping beltand the Pulley.
18

5. Unscrew twoscrewson the Sensor plate.
Unscrew one screw from each Sensor.
6. Unscrew four screwsand remove the Tapping motor.
19

7. Unscrew three screwsand remove the Up/downsensor block.
Unscrew one screw from the Up/downsensor block and remove
the Up/downsensor.
8. Unscrew twoscrewsfrom the Connection PCB (A)and remove
the Connection PCB.
Unscrew twoscrewsfrom the Connection PCB board (B)and
remove the Connection PCB board.
20