Panasonic EP3203-U1 User manual

ORDERNO.HPD0401U11C1
E11
MASSAGELOUNGER
EP3203-U1
SPECIFICATIONS
SPECIFICATIONS
1

1
1. COMPONENTSIDENTIFICATION
1.1. Massagelounger
2

1.2. Controller
3

2. MASSAGERANGE(MOVEMENTRANGEOF
MASSAGEWHEELS) SHIATSU MASSAGE, SWEDISH
MASSAGE, KNEADING, VIBRATING, TAPPING A,
TAPPING B, TAPPING C, WHOLEBACK ROLLING,
REGIONALROLLING
4

Widthadjustment
Approx.50 to210 mm (2.4in. to8.3in.)
Intensity adjustment
Shiatsu, Swedish, Knead, vibration, TapA, TapB, TapC, wholeback roll, and
Regional roll (fromgentletostrong)
:50mm(2.4in.)-wideadjustability wheremassageheadspushouttoward bodyas
intensity increases.
5

3. TURNING ONTHE POWER
6

1. Plug thepowerplug intothepowersocket.
2. Turn thelock switchtotheopenposition.
3. Turn on thepowerswitchon theback oftheunit.
-Whentheoperating lock switchispointing toward 'lock', thepowerswitch
cannotbemovedtothe'on' position.
Aftereachuse.
-Besuretoturn thepowerswitchto'off'.
-Topreventchildrenfrom using thisunit, lock thepowerswitch
bymoving theoperating lock switchtothe'lock' position.
-Asafurthercaution, unplug thepowercord from thepower
socketaftereachuse.
Timer
Whentheon/off button ispushed, atimerbeginstopreventoveruse. After
approximately15 minutes, timeexpires and themassagewheel goes intostorage
position.
7

4. REQUIRED TOOLS
8

5. ACTUALWIRING DIAGRAM
5.1. Connecting cord forpower source to Sub PCB
9

6. DISPLAYMETHODOFMASSAGEBLOCK TOTAL
USE TIMEAND OPERATIONTIME
10

Adjustmentofpressuresensor
First, keeptheMassagemechanismblock unloadedwithpressureand move it
upward halfway.
IftheMassagemechanismblock isat thehighest or lowest position, you cannot
arrangethepressuresensor correctlybecause thefabricbecomes tense with
pressure.
1. Whilepushing On/off button and theUserprogrambutton Bsimultaneously, turn
on thepowerswitchand continuetoholdthebuttonsfor approximately5
seconds. Release aftertheFocusbutton lights up.
2. PushtheFocusbutton and automaticallyitlights off.
Turn off thePowersource switchand turn iton again, thentheadjustmentis
finished.
Total use time&Display method
Whilepushing theShiatsubutton and theDeepbutton simultaneously, turn on the
powerswitchand continuetoholdthebuttonsfor approximately5seconds.
Release aftertheUserprogrambutton A.
e.g. Intheabove case, 3000 + 500 + 10 + 5= 3515 hours.
11

Itispossibletoindicate up to5,995 hours.
Iftheuse timeisless than5hours, 5hour unitdoes notlightup. Ifitisless than10
hours, one5hour unitlights up.
Chartfor reading eachfunction use time
7. MOTIONOFTHE CLUTCH AND BELTBASED ON
VARIOUS MASSAGER OPERATIONS
Massageroperation and beltmotion
12

Massageroperation and clutchmotion
8. CONTROLOFTHE AIR-MASSAGEOPERATION
13

Airmassagefunctionswiththeoperationsofthepumpunitx1pc, 3-way
electromagneticvalve x1pc, and 2-way electromagneticvalve x2pcs.
1. Airmassageisoperatedbythepumpand electromagneticvalves.
2. Whennotinoperation, all thepumpand theelectromagneticvalves areinOff
position.
3. WhentheReclining lift motor and theOttomanlift motor areinoperation, the
control ofairisstopped. (ElectromagneticisOff. Inventilation.)
4. Whenyou operate theelectricreclining lift or theelectricOttomanlift whileyou
operate On/off button or itisinwaiting mode, stop theoperation ofthepump.
(Thepressureofelectromagneticvalves aremaintained.)And aftertheoperation
stop(retracting mode) fromtheretracting modeand stop mode, or afterelectric
reclining lift or electricOttomanlift stop inthewaiting mode, airmassagestops
in5seconds.
*Afterthe3-way electromagneticvalve ofLegsbigturnsOff , turn Onthe2-way
electromagneticvalve and maintainthepressureofLegsbig.
14

9. MASSAGER UP/DOWNSENSORGEAR
ADJUSTMENTMETHOD
Whenthemassagerisremovedfromthechair, theposition oftheup/downsensor
gearchanges, resulting inachangeoftheup/downstop position.
Wheninstalling themassageron theback frame, besuretoadjust theposition with
theup/downdetection gear.
15

Up/downsensor gearposition adjustmentprocedure
1. Beforemounting, themassageron theback framemust bemoveddowntothe
lowest position bysetting thecontrollermanual operation MASSAGE HEAD
ADJUSTMENTbutton toDOWN.
2. Install Rail pieces (left/right) and screwthemwitheachthree screws.
3. Make surethat themassagerhas beenmountedhorizontallybymoving the
massager.
*Unless themassagerhas beenmountedhorizontally, anabnormal sound or
problemmay occur.
4. Move itup tothehighest position (until themassagerstops) bysetting the
controllermanual operation MASSAGE HEAD ADJUSTMENTbutton toup.
5. Peeping intothesquareholeoftheback frame, check theposition ofthe
massagertoadjust.
*Onethreadoftheup/downdetection geargives astroke changeof4mm.
Whenthemassagerhas beenraisedexcessively:Turn theup/downsensor gear
counterclockwise toadjust.
Whenthemassagerhas beenloweredexcessively:Turn theup/downsensor gear
clockwise toadjust.
16

*Whenadjusting theup/downposition, holdthe'Gear' and adjust it. (Donottouch
thedetector board.)
6. Whileadjusting thedistance betweenthesquareholeand Guiderollerassy. to
10mm, check byusing theup/downadjustmentbutton found on themanual
operation panel ofthecontroller.
7. Using themanual operation ofthecontroller, conduct therolling operation.
10. DISASSEMBLYAND ASSEMBLYINSTRUCTION
10.1. Removing theArm restand theController stand
10.1.1. Removing theArm rest
1. Unscrewahex screw(4mm)on thebottomoftheArmrest.
17

2. Pull theArmrest backward(1) and pull itup(2) and take itaway.
18

3. You canremove bothArmrests.
Tipsofinstalling
InserttheArmrest totheArmrest holdersothat bothtrianglemarks meet each
others, and pull theArmrest forward tolock.
19

10.1.2. Removing theControllerstand
1. Take off theController, and unscrewthree Hex screws(4mm)oftheController
stand.
20