Panasonic KX-TDE200 User manual

Pure IP-PBX
Getting Started
for Physical Cards
Model No. KX-TDE100
KX-TDE200
Thank you for purchasing a Panasonic Pure IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDE100/KX-TDE200: PMMPR Software File Version 2.0000 or later

2 Getting Started for Physical Cards
Table of Contents
1 Before Installation .................................................................................. 3
1.1 System Connection Diagram ...........................................................................................4
1.2 Unpacking..........................................................................................................................5
2 Installation............................................................................................... 7
2.1 Opening/Closing the Front Cover....................................................................................8
2.2 Inserting the SD Memory Card to the IPCMPR Card......................................................9
2.3 Installing the Option Units ...............................................................................................9
2.4 Installing the Trunk Cards ..............................................................................................11
2.5
Installing the Extension Cards (DLC8/DLC16/DHLC8/MSLC16/SLC8/SLC16/CSLC16) ...14
2.6 Connecting Extensions ..................................................................................................14
2.7 Frame Earth Connection ................................................................................................15
3 Before Programming ............................................................................ 17
3.1 Starting the PBX..............................................................................................................18
3.2 Connecting the PC..........................................................................................................19
3.3 Installing the Maintenance Console ..............................................................................20
4 Programming ........................................................................................ 21
4.1 Programming the PBX ....................................................................................................22
5 Confirming the Connection ................................................................. 27
5.1 Making and Receiving Calls...........................................................................................28

Getting Started for Physical Cards 3
Section 1
Before Installation

1.1 System Connection Diagram
4 Getting Started for Physical Cards
1.1 System Connection Diagram
*1ITSP: Internet Telephony Service Provider
*2DCE: Data Circuit Terminating Equipment
MSLC16
(KX-TDA0175)
SLC8
(KX-TDA0173)
EXT-CID
(KX-TDA0168)
SLC16
(KX-TDA0174)
E1
(KX-TDA0188)
IP-GW4E
(KX-TDA0484)
IP-GW16
(KX-TDA0490)
PRI30
(KX-TDA0290
CE/CJ)
PRI23
(KX-TDA0290)
BRI4
(KX-TDA0284)
BRI8
(KX-TDA0288)
T1
(KX-TDA0187)
E&M8
(KX-TDA0184)
DID8
(KX-TDA0182)
PSU-S/M/L
(KX-TDA0108/
KX-TDA0104/
KX-TDA0103)
DLC16
(KX-TDA0172)
DLC8
(KX-TDA0171)
DHLC8
(KX-TDA0170)
LCOT4
(KX-TDA0183)
LCOT16
(KX-TDA0181)
LCOT8
(KX-TDA0180)
CID/PAY8
(KX-TDA0189)
CID8
(KX-TDA0193)
V-SIPEXT32
V-IPEXT32
CSLC16
(KX-TDA0177)
SLT
Fax
Machine
SLT
(DHLC only) Wireless Phone
(DHLC only)
APT
(DHLC only)
DPT
Voice
Processing
System
DSS
Console
PT-interface CS
(Basic/High-density)
PS
KX-T7600
DPT
PCKX-T7636/
KX-T7633
KX-T7600
DPT
Radio
Amplifier Pager/Speaker
CSIF4
(KX-TDA0143)
CSIF8
(KX-TDA0144) CS PS
Private
IP Network
Station Message Detail
Recording (SMDR)
Router
Batteries
IP-EXT16
(KX-TDA0470)
OPB3
(KX-TDA0190)
DPH4
(KX-TDA0161)
DPH2
(KX-TDA0162)
ECHO16
(KX-TDA0166)
EIO4
(KX-TDA0164)
MSG4
(KX-TDA0191)
Doorphone & Door Opener
IP-PT
LAN
External Sensor/
External Relay Device
IP Softphone
ISDN BRI Line
(Digital Trunk)
ISDN BRI Line
(Digital Trunk)
ISDN PRI Line
(Digital Trunk)
ISDN PRI Line
(Digital Trunk)
T1 Line
(Digital Trunk)
T1 Line
(Digital Trunk)
Analogue
Trunk
Analogue
Trunk
E & M Line
E & M Line
E1 Line
(Digital Trunk)
E1 Line
(Digital Trunk)
Telephone
Company
Router
PC
IP Softphone
LAN
CTI Server
IPCMPR
(Installed by default)
IP-PT
SIP Extension
V-SIPGW16
V-IPGW16
Virtual
Trunk Slot Virtual Extension Slot
Private IP
Network
Mountable Equipment
PC
ITSP*1
Network
DCE*2
(e.g., ADSL
Modem)
Router
WAN
DSP16
(KX-TDE0110)
DSP64
(KX-TDE0111)
RMT
(KX-TDA0196)
ESVM2
(KX-TDA0192)
ESVM4
(KX-TDA0194)

1.2 Unpacking
Getting Started for Physical Cards 5
1.2 Unpacking
Check the package contents.
Main Unit × 1
CD-ROM (including manuals, etc.) × 1
AC Cord* × 1 Screw A
× 3 (KX-TDE100)
× 4 (KX-TDE200)
Screw B (Black)
× 2 (KX-TDE100)
× 6 (KX-TDE200)
Anchor Plug
× 3 (KX-TDE100)
× 4 (KX-TDE200)
Mini Plug (for pager and
music source) × 4
Ferrite Core (for the IPCMPR
card) × 2
SD Memory Card × 1
* The type of the AC cord may vary depending on the country/area of use.
The KX-TDE100BX/KX-TDE200BX is supplied with 2 types of AC cord. Please use whichever is
appropriate for the country/area.
In Canada, there is no ferrite core attached to the AC cord.
Note
In this manual, the suffix of each model number (e.g., KX-TDE100NE) is omitted unless
necessary.
for KX-TDE200for KX-TDE100
Metal Bracket × 1

1.2 Unpacking
6 Getting Started for Physical Cards
Necessary items (not supplied):
Telephone cable for extension connection:
The maximum length of the cable may vary depending on the type of cable and installation conditions.
An RS-232C cross cable or Ethernet straight cable for PC connection
Connectors (Amphenol/RJ45/BNC) for trunk and extension connections
Notes
• The Ethernet straight cable should be a 10BASE-T/100BASE-TX CAT 5 (Category 5) or higher
cable.
• Use a shielded twisted pair cable for the Amphenol connector.
• Use a twisted pair cable for the RJ45 connector.
Diameter of cable
(ø 0.4 mm to ø 0.6 mm)
Maximum length of cable
ø 0.5 mm 1128 m for SLT
ø 0.5 mm 720 m for KX-T7600 series
ø 0.5 mm 229 m for other DPT, APT and DSS Console

Getting Started for Physical Cards 7
Section 2
Installation

2.1 Opening/Closing the Front Cover
8 Getting Started for Physical Cards
2.1 Opening/Closing the Front Cover
Opening the Front Cover
1. Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw
cover. Turn the screw anticlockwise to loosen.
2. Slide the front cover to the right until it stops, then lift the front cover.
Closing the Front Cover
1. Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the
shelf), then slide the front cover to the left until it locks.
2. Turn the screw clockwise to tighten, then secure the screw cover.
2
1

2.2 Inserting the SD Memory Card to the IPCMPR Card
Getting Started for Physical Cards 9
2.2 Inserting the SD Memory Card to the IPCMPR
Card
The SD Memory Card contains software for all the processes of the PBX and all the customer data. The SD
Memory Card must be inserted before startup.
CAUTION
Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the PBX
to fail to start when you try to restart the system.
2.3 Installing the Option Units
Slot Position
Install the power supply unit (PSU) into the PSU slot, and optional service cards into free slots.
* Null slot is not available for any optional service card.
IPCMPR Card
Example: KX-TDE200
SD
CARD
2
SD
CARD
45
SD
CARD
SD
Memory
Card
3
1
KX-TDE100 KX-TDE200
PSU Slot
Free Slots
IPCMPR Card
PSU Slot
Free Slots
IPCMPR Card
Null Slot*

2.3 Installing the Option Units
10 Getting Started for Physical Cards
CAUTION
To protect the back board from static electricity, do not touch parts on the back board in the main unit,
PSU, and on the optional service cards. To discharge static electricity, touch ground or wear an earthing
strap. Make sure the screws are tightened to earth the card securely.
Installing the Power Supply Unit
1. Insert the PSU along the guide rails.
2. Push the release lever in the direction of the arrow, so that the PSU engages securely with the
connector on the back board.
3. Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU.
Installing the Trunk/Extension Cards
1. Insert the card along the guide rails.
2. Holding the card as shown below, push the release lever in the direction of the arrow so that the card
engages securely with the connector on the back board.
3. Turn the 2 screws clockwise to fix the card in place.
Guide Rail
Back Board
Release Lever
Screws
1
32
4
Guide Rail
Release
Lever
Back Board
Screws

2.4 Installing the Trunk Cards
Getting Started for Physical Cards 11
Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. For
details, refer to "Covering the Blank Slots" in "3.2.7 Installing/Removing the Optional Service Cards" of the
Installation Manual.
2.4 Installing the Trunk Cards
LCOT4/LCOT8/LCOT16 Card
Accessories (included): Screws × 2
User-supplied (not included): Amphenol connector
Amphenol
To trunk
Example: LCOT16 Card

2.4 Installing the Trunk Cards
12 Getting Started for Physical Cards
BRI4/BRI8 Card
Accessories (included): Ferrite core(s) × 1 (BRI4 card) or 2 (BRI8 card)
User-supplied (not included): RJ45 connector
Notes
• LINE 5 to LINE 8 are for BRI8 card only.
• Connect these optional service cards to the trunk through an NT1; do not connect to the U interface
of the trunk directly.
• These optional service cards have 100 Ωof terminal resistance. For use in point to multi-point
connection, the cards must be placed at the end of the bus.
• When connecting the RJ45 connector, attach the included ferrite core.
To NT1
LINE 1 to
LINE 8
Example: BRI8 Card
RJ45
TX2(-)
RX1(-)
RX2(+)
TX1(+)
To attach the ferrite core
•For every 4 cables, use 1 ferrite
core; a ferrite core holds a
maximum of 4 cables.
•Attach the ferrite core as close to
the card's connector as possible.
When using 1 or 2 cables:
When using 3 or 4 cables:

2.4 Installing the Trunk Cards
Getting Started for Physical Cards 13
PRI30/PRI23 Card
Accessories (included): Ferrite core × 1
User-supplied (not included): RJ45 or BNC connectors
Notes
• In some countries/areas, the PRI30 card must not be connected to the Public Switched Telephone
Network.
• Connect these optional service cards to the trunk through an NT1; do not connect to the U interface
of the trunk directly.
• Use only 1 type of connector (RJ45 or BNC) for connection of PRI30 card; RJ45 and BNC cannot
be used simultaneously. Set the termination switch to 120 Ω(default) or 75 Ωfor connector type to
be used.
• When connecting the RJ45 connector, attach the included ferrite core (except in Canada, where
the ferrite core is not necessarily required).
Example: PRI30 Card
To N T 1
To N T 1
TX-
RX-
RX+
RJ45
TX+
TX+
TX-
BNC (TX)
RX-
RX+
BNC (RX)
5 cm
To attach the ferrite core
For RJ45
120Ω
75Ω
120Ω
75Ω
OR
For BNC

2.5 Installing the Extension Cards (DLC8/DLC16/DHLC8/MSLC16/SLC8/SLC16/CSLC16)
14 Getting Started for Physical Cards
2.5 Installing the Extension Cards (DLC8/DLC16/
DHLC8/MSLC16/SLC8/SLC16/CSLC16)
Accessories (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Note
Attach the included ferrite core to the cable.
2.6 Connecting Extensions
Example: DHLC8 Card
Amphenol
3 cm
To extensions
To attach the ferrite core
To extension card
RJ11
Example: KX-T7600 Series DPT
DPT and DSS Console
KX-T7000 Series SLT
Pin Assignments
H L
T R
APT
HTRL
TO MAIN UNIT
/ PABX
H L

2.7 Frame Earth Connection
Getting Started for Physical Cards 15
2.7 Frame Earth Connection
IMPORTANT
Connect the frame of the PBX to earth.
• Proper earthing (connection to earth) is very important to protect the PBX from the bad effects of
external noise or to reduce the risk to the user of electrocution in the case of a lightning strike.
• The earthing wire of the AC cable has an effect against external noise and lightning strikes, but it may
not be enough to protect the PBX. A permanent connection between earth and the earth terminal of
the PBX must be made.
1. Loosen the screw.
2. Insert an earthing wire (user-supplied)*.
3. Tighten the screw.
4. Connect the earthing wire to earth.
* For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the
conductor must be more than 0.75 mm2or 18 AWG.
To earth
Earthing
wire
Screw

2.7 Frame Earth Connection
16 Getting Started for Physical Cards

Getting Started for Physical Cards 17
Section 3
Before Programming

3.1 Starting the PBX
18 Getting Started for Physical Cards
3.1 Starting the PBX
CAUTION
• The SD Memory Card must be inserted in the SD Memory Card slot of the IPCMPR card before
startup.
• Before touching the System Initialise Switch, discharge static electricity by touching ground or
wearing an earthing strap.
• Once you have started the PBX and if you unplug the PBX, do not perform the following procedures
to start the PBX again. Otherwise, your programmed data will be cleared.
• The PBX will continue to be powered even if the power switch is turned "OFF".
•The power supply cord is used as the main disconnect device. Ensure that the AC outlet is
located near the equipment and is easily accessible.
1. Slide the System Initialise Switch to the "SYSTEM INITIALIZE" position.
2. Plug the AC power cord into the PBX and an AC outlet, and turn on the PBX. The RUN indicator will
flash.
3. While the RUN indicator is flashing, slide the System Initialise Switch back to the "NORMAL" position.
Depending on the configuration, initialisation takes about 1 min to 3 min. If successfully executed, the
RUN indicator will stop flashing and stay lit.
All data will be cleared and the PBX will be initialised to the default values. The DPTs should show the time
as 01:00.
Note
Use only the AC power cord included with the PBX for the PSU.
System Initialise Switch
SYSTEM
INITIALIZE
NORMAL
Power
Supply Unit
RUN Indicator
To AC
Outlet

3.2 Connecting the PC
Getting Started for Physical Cards 19
3.2 Connecting the PC
The Maintenance Console serves as an overall system programming tool for the PBX. The Maintenance
Console's Quick Setup lets you easily configure the PBX to receive intercom and trunk calls, as well as apply
basic settings such as time and date.
To programme the PBX, connect it to the PC via the MNT or RS-232C port.
PC Connection
Pin Assignments
IMPORTANT
• When connecting a PC to the PBX via the MNT port, a fixed IP address must be assigned to
the PC. For information about fixed IP addresses, ask your network administrator.
• When connecting a PC to the PBX via the RS-232C port, it is necessary to keep the following
in mind to protect the system:
1. Make sure that both connector cases (frame ground) of the RS-232C cross cable
(shielded cable) are conductive. If they are not conductive, make sure that both
connector cases of the cable are firmly connected.
2. If this is not possible, connect the frame of the PBX to the frame of the PC using an
earthing wire in order to prevent difference in the electrical potentials.
MNT Port
To LAN Port
To COM Port
RS-232C Port
PC
PC
To attach the ferrite core
3 cm
RS-232C (Cross Cable)
Pin No.
2
3
4
5
6
7
8
Pin No.
2
3
4
5
6
7
8
RS-232C PortCOM Port
Pin No.
1
2
3
6
1
2
3
6
Pin No.
LAN (RJ45 Cable)
LAN Port (PC) MNT Port (PBX)

3.3 Installing the Maintenance Console
20 Getting Started for Physical Cards
3.3 Installing the Maintenance Console
For the system requirements of the PC (e.g., operating system, hardware specifications), refer to "4.3.1
Installing and Starting the Maintenance Console" in the Installation Manual.
Notes
• Make sure to install and use the latest version of the Maintenance Console.
• The contents and design of the software are subject to change without notice.
• Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
1. Copy the setup file of the Maintenance Console to your PC.
2. Double-click the setup file to run the installer.
3. Follow the on-screen instructions provided by the installation wizard.