Panasonic AK-HRP1000G User manual

DVQP2688ZAW1121AM0 -PS
ENGLISH
For details of operating Remote Operation Panel AK-HRP1000G, please
visit the Panasonic website (https://pro-av.panasonic.net/manual/en/index.
html), and refer to the Operating Instructions (HTML or PDF).
Read this document when using the AK-HRP1000G Remote Operation Panel in
conjunction with AG-CX350 Memory Card Camera-Recorder.
Operating Guide
Remote Operation Panel
Model No. AK-HRP1000G

Connecting the Unit to AG-CX350 Cameras 3
Connections 3
Compatible Functions List 4
ROP Menu (during AG-CX350 Connection) 8
ROP menu list 8
01 SHUTTER SPEED 13
02 PEDESTAL 13
03 CHROMA 14
04 GAIN 14
05 COLOR TEMP 15
06 WHITE BALANCE 15
07 GAMMA 16
08 KNEE 17
09 WHITE CLIP 18
10 DRS 18
11 DETAIL 19
12 SKIN TONE DTL 20
13 MATRIX 21
14 COLOR CORRECTION 22
15 SYSTEM CAM 24
16 CAMERA MENU CONTROL 25
17 ROP SETTING 26
18 CONNECT SETTING 27
19 ROP IP SETTING 28
20 CAMERA IP SETTING 28
21 AUTO IRIS SETTING 28
22 SWITCHER LINK 28
23 AW CONTROLLER LINK 28
- 2 -
Table of Contents

Connecting the Unit to AG-CX350 Cameras
Connections
Use a LAN cable to connect the <REMOTE> connector at the rear of the AG-CX350 to the <LAN> connector of the AK-
HRP1000G.
Set the connection setting to “LAN(AG)” in the [CONNECT SETTING] menu.
ヤヰワワユヤヵチヴユヵヵリワヨ
ヒチバチヒヒ
ヤモヮヒヤモヮビヤモヮピヤモヮフヤモヮブヤモヮプヤモヮヘヤモヮベヤモヮペワヰワワヰワワヰワワヰワワヰワワヰワロモワドモヨナワヰワワヰワヤヰワワユヤヵチヮヰュユドㄑㄖㄔㄉナヤヰワワユヤヵチヮヰュユドㄑㄖㄔㄉナヤヰワワユヤヵチヮヰュユドㄑㄖㄔㄉナ
- 3 -
Connecting the Unit to AG-CX350 Cameras

Compatible Functions List
When the unit is used in conjunction with an AG-CX350 Memory Card Camera-Recorder, a portion of the unit’s button, dial, and other con-
trol functions will be limited or disabled. Be sure to refer to the following table.
Front panel 1
Front panel 2
Front panel 3
Front panel 4
Front panel 5
Front panel 6
Front panel 7
Front panel 8
Front panel 9
Number Part name
✓: Enabled
×: Disabled
Remarks
Front panel 1
[POWER HEAD] button ×
[POWER VF] button ×
[BARS/TEST] button ✓Only the ON/OFF for the color bar signal output will
function.
[REF. RECALL] button ×
[AUTO WHITE] button ✓This functions when the [WHITE BALANCE] >
[W.BAL SELECT] setting is “A” or “B”.
[AUTO BLACK] button ✓
[AUTO SET UP] button ×
[CHARA] button ✓
[MATRIX] button ✓
[SKIN DTL] button ×
[DRS] button ✓
[B.GAMMA] button ×
[ASSIGN] button ✓
- 4 -
Connecting the Unit to AG-CX350 Cameras

Number Part name
✓: Enabled
×: Disabled
Remarks
Front panel 2
[ASSIGN STATUS] button ✓
Buttons [1] to [5] (CONTROL/MODE) ✓
[CONTROL/MODE] button ✓
Front panel 3
LCD panel ✓
[MENU] dial ✓
[EXIT] button ✓
[UNDO] button ×
[MENU] button ✓
Front panel 4
[ON] indicator (SCENE FILE) ✓This is always lit.
Scene file page switching button ×
[1/6], [2/7], [3/8], [4/EXT1], and
[5/EXT2] buttons (SCENE FILE)
✓Scenes 1 to 6 are enabled.
[STORE] button ✓When you press this at the same time as the [HEAD]
button, recording starts or stops.
Front panel 5
[ND] indicator ✓
[ND] setting buttons ✓
[ND] display ✓Displayed but cannot be adjusted.
[CC] indicator ×
[CC] setting buttons ×
[CC] display ×
[HEAD] button ✓When you press this at the same time as the
[STORE] button, recording starts or stops.
[ECC] button ×
[M.GAIN] indicator ✓
[M.GAIN] setting buttons ✓
[M.GAIN] display ✓Display varies depending on the selected mode.
When dB mode is selected:
Displays the dB setting value.
When ISO mode is selected:
Displays the ISO setting value (the last two digits
of the setting value are not displayed). A dot is
displayed at the bottom right.
[VAR] button ×
- 5 -
Connecting the Unit to AG-CX350 Cameras

Number Part name
✓: Enabled
×: Disabled
Remarks
Front panel 6
[SHUTTER] display ✓Display varies depending on the shutter mode.
When auto shutter is selected:
Displays “AUTO”.
When fixed shutter is selected:
Displays the numerical value for the denom-
inator of the shutter speed.
When synchro scan (time display) is selected:
Displays the numerical value for the denom-
inator of the shutter speed. When the value is
four or more digits, the digits after the decimal
point are not displayed.
When synchro scan (shutter open angle dis-
play) is selected:
Displays the shutter open angle.
[ON] button (SHUTTER) ✓
[SYNC] button (SHUTTER) ✓Changes the shutter mode of the electronic shutter.
OFF:
Fixed shutter (FIX)
ON:
Synchro scan (SYNC)
[SHUTTER] setting buttons ✓
Front panel 7
[GAIN R], [GAIN G], and [GAIN B]
dials
✓[GAIN G] dial is disabled.
[BLACK R], [BLACK G], and [BLACK
B] dials
✓FLARE cannot be controlled. “-” is displayed.
[FLARE] button ✓
[PAINT LOCK] button ✓
[DTL] dial ✓
[CAM SEL] indicator ✓
[SELECT] dial ✓
[TEMP] indicator ✓
[SYNC] indicator ✓
[MFLR] indicator ×
[USER] indicator ✓
- 6 -
Connecting the Unit to AG-CX350 Cameras

Number Part name
✓: Enabled
×: Disabled
Remarks
Front panel 8
[EXT] indicator ×
[D.EXT] indicator ×
[IRIS] lever ✓
[M.PED] dial ✓
[RELATIVE] button ✓
[SENSE] dial ✓
[COARSE] dial ✓
[IRIS] display ✓
[AUTO] button ✓
[CLOSE] button ×
[M.PED] display ✓
[IRIS LOCK] button ✓
[M.PED LOCK] button ✓
Front panel 9
Camera number/tally display ✓
[ALM] indicator ✓
[OPT] indicator ×
[PANEL ACTIVE] button ✓
[CALL] button ×
[PREVIEW] button ×
Memory card slot ✓
Memory card access indicator ✓
Torque adjustment screw ✓
- 7 -
Connecting the Unit to AG-CX350 Cameras

ROP Menu (during AG-CX350 Connection)
ROP menu list
When an AG-CX350 Memory Card Camera-Recorder is connected, the ROP menu will be as follows. For setting values related to the cam-
era, refer to the Operating Instructions for the camera.
For details on menu operations, refer to the following sections in the Operating Instructions.
“Displaying menus”
“Basic menu operations”
NOTE
To perform menu operations, upgrade the version of the unit system to 5.10-00-0.00 or later.
The setting values of functions that are not supported are indicated as “－”.
01 SHUTTER SPEED
SHUTTER “SHUTTER” (see page 13)
SPEED MODE “SPEED MODE” (see page 13)
SYNC TYPE “SYNC TYPE” (see page 13)
SPEED “SPEED” (see page 13)
AUTO SHUTTER “AUTO SHUTTER” (see page 13)
AUTO SHUTTER LIMIT “AUTO SHUTTER LIMIT” (see page 13)
AUTO SHUTTER POINT “AUTO SHUTTER POINT” (see page 13)
02 PEDESTAL
M.PED “M.PED” (see page 13)
OFFSET “OFFSET” (see page 13)
PED R “PED R” (see page 13)
PED G “PED G” (see page 13)
PED B “PED B” (see page 13)
03 CHROMA
LEVEL % “LEVEL %” (see page 14)
PHASE “PHASE” (see page 14)
04 GAIN
GAIN “GAIN” (see page 14)
AGC “AGC” (see page 14)
AGC LIMIT “AGC LIMIT” (see page 14)
AGC POINT “AGC POINT” (see page 14)
05 COLOR TEMP
COLOR TEMP “COLOR TEMP” (see page 15)
GAIN R “GAIN R” (see page 15)
AXIS G “AXIS G” (see page 15)
GAIN B “GAIN B” (see page 15)
06 WHITE BALANCE
W.BAL SELECT “W.BAL SELECT” (see page 15)
GAIN OFFSET “GAIN OFFSET” (see page 15)
GAIN R “GAIN R” (see page 15)
GAIN B “GAIN B” (see page 15)
ATW SPEED “ATW SPEED” (see page 15)
ATW TARGET R “ATW TARGET R” (see page 15)
ATW TARGET B “ATW TARGET B” (see page 15)
- 8 -
ROP Menu (during AG-CX350 Connection)

07 GAMMA
MODE “MODE” (see page 16)
GAMMA “GAMMA” (see page 16)
F-REC DYNMC LV “F-REC DYNMC LV” (see page 16)
F-REC BLK.S LV “F-REC BLK.S LV” (see page 16)
V-REC K.SLOPE “V-REC K.SLOPE” (see page 16)
V-REC K.POINT “V-REC K.POINT” (see page 16)
BLACK GAMMA “BLACK GAMMA” (see page 16)
B.GAMMA RANGE “B.GAMMA RANGE” (see page 16)
08 KNEE
MODE “MODE” (see page 17)
POINT “POINT” (see page 17)
SLOPE “SLOPE” (see page 17)
A. KNEE RSPNS “A. KNEE RSPNS” (see page 17)
HLG KNEE SW “HLG KNEE SW” (see page 17)
HLG KNEE POINT “HLG KNEE POINT” (see page 17)
HLG KNEE SLOPE “HLG KNEE SLOPE” (see page 17)
H.COLR SW “H.COLR SW” (see page 17)
09 WHITE CLIP
WHITE CLIP SW “WHITE CLIP SW” (see page 18)
WHITE CLIP LEVEL(%) “WHITE CLIP LEVEL(%)” (see page 18)
10 DRS
DRS “DRS” (see page 18)
EFFECT DEPTH “EFFECT DEPTH” (see page 18)
11 DETAIL
DTL “DTL” (see page 19)
CORING “CORING” (see page 19)
V.DTL LEVEL “V.DTL LEVEL” (see page 19)
FREQ. “FREQ.” (see page 19)
LEVEL DEPEND. “LEVEL DEPEND.” (see page 19)
KNEE APE LV “KNEE APE LV” (see page 19)
GAIN(+) “GAIN(+)” (see page 19)
GAIN(-) “GAIN(-)” (see page 19)
DTL SW “DTL SW” (see page 19)
12 SKIN TONE DTL
SKIN TONE DTL A “SKIN TONE DTL A” (see page 20)
SKIN TONE DTL B “SKIN TONE DTL B” (see page 20)
SKIN TONE DTL C “SKIN TONE DTL C” (see page 20)
DETECT TBL “DETECT TBL” (see page 20)
EFFECT “EFFECT” (see page 20)
I CENTER “I CENTER” (see page 20)
I WIDTH “I WIDTH” (see page 20)
Q WIDTH “Q WIDTH” (see page 20)
Q PHASE “Q PHASE” (see page 20)
13 MATRIX
TYPE “TYPE” (see page 21)
ADAPTIVE MATRIX “ADAPTIVE MATRIX” (see page 21)
R-G “R-G” (see page 21)
R-B “R-B” (see page 21)
G-R “G-R” (see page 21)
G-B “G-B” (see page 21)
B-R “B-R” (see page 21)
B-G “B-G” (see page 21)
- 9 -
ROP Menu (during AG-CX350 Connection)

14 COLOR CORRECTION
SAT R “SAT R” (see page 23)
PHASE R “PHASE R” (see page 23)
SAT R-R-Mg “SAT R-R-Mg” (see page 23)
PHASE R-R-Mg “PHASE R-R-Mg” (see page 23)
SAT R-Mg “SAT R-Mg” (see page 23)
PHASE R-Mg “PHASE R-Mg” (see page 23)
SAT Mg “SAT Mg” (see page 23)
PHASE Mg “PHASE Mg” (see page 23)
SAT Mg-B “SAT Mg-B” (see page 23)
PHASE Mg-B “PHASE Mg-B” (see page 23)
SAT B “SAT B” (see page 23)
PHASE B “PHASE B” (see page 23)
SAT B-Cy “SAT B-Cy” (see page 23)
PHASE B-Cy “PHASE B-Cy” (see page 23)
SAT Cy “SAT Cy” (see page 23)
PHASE Cy “PHASE Cy” (see page 23)
SAT Cy-G “SAT Cy-G” (see page 23)
PHASE Cy-G “PHASE Cy-G” (see page 23)
SAT G “SAT G” (see page 23)
PHASE G “PHASE G” (see page 23)
SAT G-Yl “SAT G-Yl” (see page 23)
PHASE G-Yl “PHASE G-Yl” (see page 23)
SAT G-Yl-Yl “SAT G-Yl-Yl” (see page 23)
PHASE G-Yl-Yl “PHASE G-Yl-Yl” (see page 23)
SAT Yl “SAT Yl” (see page 23)
PHASE Yl “PHASE Yl” (see page 23)
SAT Yl-Yl-R “SAT Yl-Yl-R” (see page 23)
PHASE Yl-Yl-R “PHASE Yl-Yl-R” (see page 24)
SAT Yl-R “SAT Yl-R” (see page 24)
PHASE Yl-R “PHASE Yl-R” (see page 24)
SAT Yl-R-R “SAT Yl-R-R” (see page 24)
PHASE Yl-R-R “PHASE Yl-R-R” (see page 24)
15 SYSTEM CAM
TALLY CONTROL “TALLY CONTROL” (see page 24)
TALLY INPUT “TALLY INPUT” (see page 24)
TALLY SIGNAL “TALLY SIGNAL” (see page 24)
TALLY CONT MD “TALLY CONT MD” (see page 24)
16 CAMERA MENU CONTROL
MENU ON/OFF “MENU ON/OFF” (see page 25)
CURSOR/PARAMETER “CURSOR/PARAMETER” (see page 25)
EXECUTE “EXECUTE” (see page 25)
MENU EXIT “MENU EXIT” (see page 25)
- 10 -
ROP Menu (during AG-CX350 Connection)

17 ROP SETTING
CONTROL(MENU)1 “17 ROP SETTING” (see page 26)
CONTROL(MENU)2
CONTROL(MENU)3
CONTROL(MENU)4
CONTROL(MENU)5
B.GAMMA SW
MODE(ON/OFF)1
MODE(ON/OFF)2
MODE(ON/OFF)3
MODE(ON/OFF)4
MODE(ON/OFF)5
ECC BTN CTRL
ASSIGN BUTTON
USER ASSIGN
IRIS LEV MODE
CAM SEL
DTL VOL
SKIN DTL SW
LCD BRIGHT
PANEL LED BRIGHT
7SEG BRIGHT GROUP1
7SEG BRIGHT GROUP2
BUZZER
PERIOD
CYCLE
STD POSITION M.GAIN
STD POSITION VAR
STD POSITION ND
STD POSITION CC
IRIS PRIORITY
ROP DATA SAVE
ROP DATA LOAD
SD CARD FORMAT
INITIAL with NW
INITIAL
POWER BUTTON
IRIS CALIBRATION TOP
IRIS CALIBRATION BOTTOM
RELATIVE MODE
UPGRADE
PAINT VOL CO
SYSTEM VERSION
SOFT VERSION
FPGA VERSION
18 CONNECT SETTING
CONNECT MODE(push) CAM1 “CONNECT MODE(push) CAM1” (see page 27)
CONNECT MODE(push) CAM2 to
CAM99
“CONNECT MODE(push) CAM2 to CAM99” (see
page 27)
- 11 -
ROP Menu (during AG-CX350 Connection)

19 ROP IP SETTING
ROP IP ADDRESS Refer to the following section in the Operating Instructions.
“36 ROP IP SETTING”
ROP PORT
UPLOAD
ROP SUBNET MASK
UPLOAD
ROP DEFAULT GATEWAY
UPLOAD
MAC ADDRESS
20 CAMERA IP SETTING
CAM1 to CAM99 IP ADDRESS Refer to the following section in the Operating Instructions.
“37 CAMERA IP SETTING”
CAM1 to CAM99 PORT
CAM1 to CAM99 INF UPLOAD
21 AUTO IRIS SETTING
AUTO IRIS LEVEL “AUTO IRIS LEVEL” (see page 28)
AUTO IRIS SPEED “AUTO IRIS SPEED” (see page 28)
AUTO IRIS WINDOW “AUTO IRIS WINDOW” (see page 28)
22 SWITCHER LINK
SWITCHER IP ADDRESS Refer to the following sections in “Functions Added by Ver-
sion Updates”.
“Functions Linking with AV-HS6000”
SWITCHER UDP PORT
INFO UPLOAD
SWITCHER LINK
TALLY RECEIVE
PREVIEW
TALLY ACTION MATERIAL
TALLY ACTION CAM No.
23 AW CONTROLLER LINK
RECEIVE PORT Refer to the following sections in “Functions Added by Ver-
sion Updates”.
“Functions Linking with AW-RP150”
INFO UPLOAD
AW CONT LINK
- 12 -
ROP Menu (during AG-CX350 Connection)

01 SHUTTER SPEED
ヴラヶヵヵユンチヴヱユユュ
ヒチバチヒ
ヴラヶヵヵユンヴヱユユュヮヰュユヴヺワヤヵヺヱユヴヱユユュヴユヤヰワヒパパョリヹヴラヶヵヵユンロリヮリヵヱヰリワヵヰョョヒバビブパョベハパモヶヵヰチヴラヶヵヵユン
Item Setting details
SHUTTER Switches the shutter function ON/OFF.
SPEED MODE Switches between fixed shutter and synchro scan.
SYNC TYPE Switches the unit of the shutter setting.
SPEED Sets the shutter speed in the unit selected in [SYNC TYPE].
AUTO SHUTTER Switches the auto shutter function ON/OFF.
AUTO SHUTTER LIMIT Sets the maximum level of the auto shutter speed.
AUTO SHUTTER POINT Sets the F value to switch control from auto iris to auto shutter during the auto shutter operation.
02 PEDESTAL
ヱユュユヴヵモロ
ヒチバチヒ
ヮハヱユュヰョョヴユヵヰョョヌヒプパンヨパパャヱユュ
Item Setting details
M.PED Adjusts the black level (master pedestal level adjustment).
OFFSET Sets the R channel, G channel, and B channel pedestal levels when the auto black balance is adjusted.
PED R Adjusts the R channel pedestal.
PED G Adjusts the G channel pedestal.
PED B Adjusts the B channel pedestal.
- 13 -
ROP Menu (during AG-CX350 Connection)

03 CHROMA
ヤランヰヮモ
ヒチバチヒ
ロユヷユロチテヱラモヴユパパ
Item Setting details
LEVEL % Sets the color intensity of images.
PHASE Finely adjusts the color phase of images.
04 GAIN
ヨモリワ
ヒチバチヒ
ヨモリワモヨヤチロリヮリヵチヱヰリワヵプ
ㄅャ ョフハパヒビ
ㄅャ
ヰョョモヨヤ
Item Setting details
GAIN Adjusts the gain of video.
AGC Enables or disables the auto gain function.
AGC LIMIT Sets the maximum gain-up amount when [AGC] is set to “ON”.
AGC POINT Sets the F value to switch control from auto iris to auto gain when [AGC] is “ON”.
- 14 -
ROP Menu (during AG-CX350 Connection)

05 COLOR TEMP
ヤヰロヰンチヵユヮヱ
ヒチバチヒ
ヤヰロヰンヵユヮヱピビパパヨモリワモヹリヴヨモリワパンヨパパャ
Item Setting details
COLOR TEMP Sets the color temperature.
GAIN R Sets the red correction level for the color temperature.
AXIS G Sets the green correction level for the color temperature.
GAIN B Sets the blue correction level for the color temperature.
06 WHITE BALANCE
ヸラリヵユチャモロモワヤユ
ヒチバチヒ
ヸハャモロヴユロユヤヵヨモリワヰョョヴユヵヴヱユユュヵモンヨユヵチンヵモンヨユヵチャワヰンヮモロピビパパレヰョョパパパンパャモヵヸヨモリワ
Item Setting details
W.BAL SELECT Sets the mode for the white balance.
GAIN OFFSET Sets the value of the R channel gain and B channel gain for when [W.BAL SELECT] is set to A (AWB A) or B
(AWB B) and automatic white balance is performed.
GAIN R Adjusts the R channel gain.
GAIN B Adjusts the B channel gain.
ATW SPEED Sets the control speed of the ATW function.
ATW TARGET R Finely adjusts the R channel output when converged in the auto tracking white balance operation.
ATW TARGET B Finely adjusts the B channel output when converged in the auto tracking white balance operation.
- 15 -
ROP Menu (during AG-CX350 Connection)

07 GAMMA
ヨモヮヮモ
ヒチバチビ
ヮヰュユヨモヮヮモュヺワヮヤチロヷャロレハヴチロヷレハヴロヰヱユレハヱヰリワヵラュプパパパハフブブパパパピパヷノンユヤョノンユヤ
ヨモヮヮモ
ビチバチビ
ャロモヤレヨモヮヮモャハヨモヮヮモチンモワヨユヒパ
Item Setting details
MODE Selects the type of gamma curve.
GAMMA Adjusts the gamma correction level. This is enabled when [MODE] is other than “HLG”.
F-REC DYNMC LV Sets the dynamic range. This is enabled when [MODE] is “F-REC” (FILM REC).
F-REC BLK.S LV Sets the black stretch. This is enabled when [MODE] is “F-REC” (FILM REC).
V-REC K.SLOPE Sets the knee slope. This is enabled when [MODE] is “V-REC” (VIDEO REC).
V-REC K.POINT Sets the knee point. This is enabled when [MODE] is “V-REC” (VIDEO REC).
BLACK GAMMA Sets the gamma curve for dark areas.
B.GAMMA RANGE Sets the maximum level for compression/expansion.
- 16 -
ROP Menu (during AG-CX350 Connection)

08 KNEE
レワユユ
ヒチバチビ
ヮヰュユヱヰリワヵヴロヰヱユモハレワユユンヴヱワヴヴヸヱヰリワヵヴロヰヱユヰョョモヶヵヰフペピハパブブペペヒパラロヨチレワユユ
レワユユ
ビチバチビ
ラハヤヰロンチヴヸヰョョ
Item Setting details
MODE Sets the operating mode for gradation compression (knee).
POINT Sets the compression level (knee point) position for high-brightness video signals.
This is enabled when [MODE] in the [GAMMA] menu is other than “HLG”, and [MODE] is “MANUAL”.
SLOPE Sets the knee slope.
This is enabled when [MODE] in the [GAMMA] menu is other than “HLG”, and [MODE] is “MANUAL”.
A. KNEE RSPNS Sets the auto knee response speed.
This is enabled when [MODE] in the [GAMMA] menu is other than “HLG”.
HLG KNEE SW Enables or disables knee operation for HLG.
This is enabled when [MODE] in the [GAMMA] menu is “HLG”.
HLG KNEE POINT Sets the knee point position for HLG.
This is enabled when [MODE] in the [GAMMA] menu is “HLG”.
HLG KNEE SLOPE Sets the knee slope for HLG.
This is enabled when [MODE] in the [GAMMA] menu is “HLG”.
H.COLR SW This does not function with AG-CX350.
- 17 -
ROP Menu (during AG-CX350 Connection)

09 WHITE CLIP
ヸラリヵユチヤロリヱ
ヒチバチヒ
ヴヸロユヷユロドテナヰワヒパペヸラリヵユチヤロリヱ
Item Setting details
WHITE CLIP SW Enables or disables the white clip function.
This is enabled when [MODE] in the [GAMMA] menu is other than “HLG”.
WHITE CLIP LEVEL(%) Sets the white clip level.
This is enabled when [WHITE CLIP SW] is “ON” and when [MODE] in the [GAMMA] menu is other than
“HLG”.
10 DRS
ュンヴ
ヒチバチヒ
ュンヴヰョョユョョユヤヵュユヱヵラヒ
Item Setting details
DRS Switches the dynamic range stretcher function, which performs correction appropriately when video with high
light/dark contrast is displayed, ON/OFF.
EFFECT DEPTH Sets the compression level for high-brightness areas of the dynamic range stretcher function.
- 18 -
ROP Menu (during AG-CX350 Connection)

11 DETAIL
ュユヵモリロ
ヒチバチビ
ュヵロヤヰンリワヨロユヷユロュユヱユワュハレワユユモヱユチロヷヒブパビパヷハュヵロロユヷユロョンユヲハパパ
ュユヵモリロ
ビチバチビ
ヨモリワドヌナヨモリワドノナュヵロヴヸパパヰワ
Item Setting details
DTL Adjusts the contour correction level (master).
This is enabled when [DTL SW] is “ON”.
CORING Sets the level of signal (including noise) that does not activate the detail effect.
This is enabled when [DTL SW] is “ON”.
V.DTL LEVEL Adjusts the vertical contour correction level.
This is enabled when [DTL SW] is “ON”.
FREQ. Sets the thickness (boost frequency) of the detail.
This is enabled when [DTL SW] is “ON”.
LEVEL DEPEND. Compresses the detail of dark areas when detail of the brightness signal is emphasized. The larger the set-
ting value the more that detail of bright areas is compressed.
This is enabled when [DTL SW] is “ON”.
KNEE APE LV Sets the detail level of high-brightness areas (extremely bright areas).
This is enabled when [DTL SW] is “ON”.
GAIN(+) Sets the detail level of the plus direction (to make brighter).
This is enabled when [DTL SW] is “ON”.
GAIN(-) Sets the detail level of the minus direction (to make darker).
This is enabled when [DTL SW] is “ON”.
DTL SW Sets the detail function (video contour adjustment) to ON/OFF.
- 19 -
ROP Menu (during AG-CX350 Connection)

12 SKIN TONE DTL
ヴレリワチヵヰワユチュヵロ
ヒチバチビ
モャヤュユヵユヤヵヵャロユョョユヤヵリチヤユワヵユンリチヸリュラヵヰョョモヰョョヰョョピブビヒプヴレリワチヵヰワユチュヵロ
ヴレリワチヵヰワユチュヵロ
ビチバチビ
ヲチヸリュヵラヲチヱラモヴユビパ
Item Setting details
SKIN TONE DTL A Sets the skin color table (skin tone detail A) used when applying skin tone detail to ON/OFF.
SKIN TONE DTL B Sets the skin color table (skin tone detail B) used when applying skin tone detail to ON/OFF.
SKIN TONE DTL C Sets the skin color table (skin tone detail C) used when applying skin tone detail to ON/OFF.
DETECT TBL Selects the skin color table of the subject for which to set the skin detail.
EFFECT Sets the effect level of skin tone detail.
I CENTER Sets the center position (sets the area to which skin tone is applied) on the I axis.
I WIDTH Sets the width of the area to which skin tone is applied on the I axis using the [I CENTER] setting as the cen-
ter.
Q WIDTH Sets the width of skin tone areas.
Q PHASE Sets the phase of the area to which skin tone is applied using the Q axis as the reference.
- 20 -
ROP Menu (during AG-CX350 Connection)