Panasonic aw-he40 series User manual

●This is to explain the procedure for allowing AW-HE40 series cameras to be used via
AW-RP50 controller.
For detailed explanations, please see each Operating Instructions.
【IP Connection】
(Point) Through a hub, AW-RP50 controller can control up to 100 remote cameras.
Connect [LAN] on AW-RP50 rear panel and [LANACT/LINK] on AW-HE40 rear panel using a LAN cable.
【Serial Connection】
(Point) The cable can be extended up to 1,000m.
AW-RP50 controller can control up to five AW-HE40 cameras via serial connection.
Connect TO PAN/TILT HEAD [1] –[5] on AW-RP50 rear panel and [RS-422] on AW-HE40 rear panel using
a LAN cable.
※TO PAN/TILT HEAD ports [1] –[5] correspond to AW-RP50 connection settings “CAM1” – “CAM5”,
respectively.
If you want to use AW-RP50 “CAM3” for serial controlling of the camera, please connect a LAN cable
with TO PAN/TILT HEAD port [3].
Remote Camera Installation & Setup Guide
1．Connecting the LAN Cable
(AW-RP50 Rear Panel)
(AW-HE40 Rear Panel)
HUB
(LAN Cable)
Category 5 or higher, Up to 100m
(LAN Cable)
Category 5 or higher, Up to 100m
<For PoE+ Hub >
Category 5e or higher, Up to 100m
(AW-RP50 Rear Panel)
(AW-HE40 Rear Panel)
(LAN Cable)
Category 5 or higher, Up to 1,000m
Straight cable
Direct Connection
(Through a hub)

【Controlling One AW-HE40 Camera via AW-RP50 Controller】
①Press MENU button. - (Fig. 1-A)
②Press [10] SYSTEM button. - (Fig. 1-B)
＊“[1] CAMERA CTL” will be displayed on the LCD screen. - (Fig. 2)
＊If it is not displayed, turn F1 dial to make “[1] CAMERA CTL” appear.
③While “[1] CAMERA CTL” is displayed on the LCD, press F1 dial. – (Fig. 1-C)
(“[1] CAM1” will be displayed on the upper half, and the connection method (default: [NoAsign]) on the
lower half of the LCD screen.)
＊If it is not displayed, turn F1 dial to make [CAM1] appear.
【IP Connection】
④Turn F2 dial to select [Network], then press F2 dial to determine the setting. –(Fig. 1-D)
【Serial Connection】
④Turn F2 dial to select [Serial], then press F2 dial to determine the setting. –(Fig. 1-D)
If the setting is executed correctly, the LED
marked with 〇will light up according the
status display lamp of the camera.
Status Display Lamp
【Serial Connection】
【IP Connection】
Lit in Orange ・・・ Standby Mode (Factory Default)
Turning-on operation needs to be done.
Lit in Green ・・・ Turned-On State
(Image is being output.)
1.CAM1
Network
［1］CAMERA CTL
MENU ON ⇒Select [10]
Press F1
Turn F2 to select ⇒Press F2 to set
(Figure 1: AW-RP50 Control Panel)
(Figure 2: AW-RP50 LCD Panel)
（A）
（B）
（C）
（D）
2．Operating AW-RP50 Controller to Set Up the Network Connection with AW-HE40 Camera
(Status Display Lamp ・・・ Shows the camera’s power status)
1.CAM1
Serial

・ For details about connection settings, please see the following illustrated manuals.
(IP Connection): “Controlling AW-HE40 via AW-RP50 Controller”
(Serial Connection): “Controlling AW-HE40 with AW-RP50 (via Serial Connection)”
【Controlling Multiple AW-HE40 Cameras via AW-RP50 Controller】
Connecting multiple cameras is usually done by “AUTO SET IP” which is executed via AW-RP50
controller.
The controller detects the cameras in the same subnet (a range divided by a router), links them to the
camera numbers where [NoAsign] is set, and then automatically assigns pre-registered IP addresses to
those cameras.
Connection Setting: [SYSTEM] menu ＞[CAMERA CTL] ＞[CAM1 –100] ⇒[NoAsign]
IPAddress Setting: [SYSTEM] menu ＞[CAM IP ADR] ＞[CAM1 –100] ⇒[Registered IP Address]
①Press MENU button. –(Fig. 3-A)
②Press [10] SYSTEM button. –(Fig. 3-B)
③Turn F1 dial –(Fig. 3-C) to select [5] AUTO SET IP.
④Press F1 dial to make [RENEW IP ADR] appear on the lower half of the LCD screen.
＊If it does not appear, turn F2 dial –(Fig. 3-D) to make [RENEW IP ADR] appear.
⑤While [RENEW IP ADR] is displayed, press F2 dial. The number of units AW-RP50 has newly
detected and the number of units it currently manages (all the remote cameras and switchers) will be
displayed on the upper half of the LCD screen. (*1)
⑥[NO] will be displayed on the lower half of the LCD screen. So, turn F2 dial to select [YES] and then
press F2 dial.
⑦When [COMPLETE] is displayed on the lower half of the LCD screen, the setting-up is completed.
Example:
AW-RP50 detects Cameras A, B and C.
[CAMERA CTL] → [NoAsign] for all of [CAM1 – 3]
[CAM IP ADR] → If the following are IP addresses of [CAM1 – 3],
CAM1: 192. 168. 0. 10
CAM2: 192. 168. 0. 11
CAM3: 192. 168. 0. 12
IP addresses of the cameras are set up as follows.
Camera A: 192. 168. 0. 10 ＊Controlled via AW-RP50/CAM1
Camera B: 192. 168. 0. 11 ＊Controlled via AW-RP50/CAM2
Camera C: 192. 168. 0. 12 ＊Controlled via AW-RP50/CAM3

(*1) The cameras (C) and switchers (S) that AW-RP50 manages are displayed as follows.
After setting up, LED buttons 1 –3 at <CAMERA STATUS / SELECTION> on the AW-RP50 operation
panel light up according to the camera’s power status. If a camera is in STANDBY mode (turned off:
factory default), it lights up in orange. If in POWER ON mode (turned on), it lights up in green.
・ For details, please see the illustrated manual “Controlling Multiple AW-HE40 Cameras via
AW-RP50 Controller”.
[1]CAMERA CTL
MENU ON ⇒Select [10]
[5]AUTO SET IP
1．AUTO SET
RENEW IP ADR
Turn F1
Press F1
C:003/003 S:1/1
NO↓
C:003/003 S:1/1
YES↓
C:003/003 S:1/1
COMPLETE
Turn F2
Press F2
Press F2
②Currently managed cameras + ①
③Newly detected switchers
④Currently managed switchers + ③
①
②
③
④
C:003/003 S:1/1
①Newly detected cameras
①
②
④
（A）
（B）
（C）
（D）
(Figure 3：AW-RP50 Control Panel)
③

★Procedure for switching over from Standby (lit in orange) to Turned-On state (lit in green) on
the camera linked to “CAM1”.
①Hold down the button [1]. –(Fig. 4-A) [POWER OFF] will be displayed on the LCD screen.
While the button [1] is held down, turn F2 dial –(Fig. 4-B) to change the setting to [POWER: ON], and
then press F2 dial. The camera will switch over to POWER ON mode (turned-on).
※If the setting is changed to [POWER: OFF] while being in the turned-on state, the camera will switch
over to Standby mode.
・ For details, please see the illustrated manual “Turning ON/OFF Remote Camera Using
AW-RP50”.
3．Turning AW-HE40 Camera On
(Turning ON)
Hold down Button 1
Turn F2
Press F2 to set
(Figure 4: AW-RP50 Control Panel)
（A）
（B）
(AW-RP50 LCD Panel)
CAM［1］<AW-HE40>
POWER：OFF↓
CAM［1］<AW-HE40>
POWER：ON↓
――― This is the end of explanations of basic setting up. ―――

●This section provides noteworthy operating or setting procedures
selected from frequently asked questions to us.
★Turning upside down the output image from the camera assigned to [CAM1]
①Press the Button 1 at <CAMERA STATUS/SELECTION>. –(Fig. 5-A)
Hold down CAMERA OSD button –(Fig. 5-B) for 2 seconds. The button will light up. (To put it out,
hold it down again for 2 seconds.) And the on-screen menu (Fig. 6) will be opened on the SDI (or
HDMI) output image.
②Use F1 dial –(Fig. 5-C) to change the camera menu setting below.
Procedure: System ＞Others ＞Others 1/4 ＞Install Position ⇒Select [Hanging].
・ For details, please see the illustrated manual “AW-HE40 –Turning Image Upside Down”.
My camera is installed on the ceiling. How can I turn the image upside down?
(Figure 6: AW-HE40 On-Screen Menu)
(Figure 5: AW-RP50 Control Panel)
Turn F1 →Select “System” →
Press F1
Turn F1 →Select “Others” →
Press F1
・Press F1 →[Desktop] blinks.
・Turn F1 →Select [Hanging].
・Press F1 →Setting determined
（A）
（B）
（C）
Desktop ：Stand-alone Installation
Hanging ：Suspended Installation

★To boot up the camera with its view angle fixed, please use [POWER ON Preset
Function (*2)].
(*2) A function to memorize the angle of view immediately before the power status switches
over to Standby mode
★[HOME POSITION] is for moving to the forward-facing position. It is impossible to change
this position.
①Set the camera’s angle of view.
②Change the camera’s power status to Standby mode.
※For the procedure for changing the power status mode, please see “3. Turning AW-HE40 Camera
ON” of this Guide.
③Turn the power on again.
Setting up is now completed.
If you fail to bring the camera into Standby mode and disconnect the power supply at the AC power
feeding side, the view angle will not be memorized.
Accordingly, after having been set up, the camera will always boot up with its fixed view angle by
powering it ON/OFF at the AC power feeding side.
・ For details, please see the illustrated manual “AW-HE40 –Booting Up with Pan-Tilt Head in
Specified Position”.
How can I boot up the camera with its angle of view fixed when I turn on its power?
Isn’t it possible to set the camera’s [HOME POSITION]?

【Registering a Preset Memory】
①Press one of CAMERA STATUS/SELECTION buttons 1 –5 to select a remote camera to be operated.
–(Fig. 7-A)
②Control the PAN/TILT and ZOOM to set the angle of view. Adjust the FOCUS and IRIS as necessary.
③Press STORE button. –(Fig. 7-B) *STORE button will light up.
④From among the PRESET MEMORY/MENU buttons –(Fig. 7-C), hold down a number you desire to
register until “STORE COMPLETE” is displayed on the LCD Panel.
*After the registration is completed, the numbered button will light up.
*If an already-registered number is registered again, the preset is overwritten.
⑤Press STORE button. –(Fig. 7-B) *STORE button will go off.
【Recalling a Preset Memory】
①Press one of CAMERA STATUS/SELECTION buttons 1 –5 to select a remote camera to be operated. –
(Fig. 7-A)
②Press an already-registered number (from among the PRESET MEMORY/MENU buttons –(Fig. 7-C)),
and the camera will move into a registered position.
・ For details, please see the illustrated manual “AW-RP50 –Setting & Controlling Preset
Memories”.
How can I register and recall the camera’s preset memories?
PRESET
STORE COMPLETE
(AW-RP50 LCD Panel)
（B）
（A）
（C）
(Figure 7: AW-RP50 Control Panel)
（D）
PRESET
DELETE COMPLETE
(Deleting a Preset Memory)
Press DELETE button –(Fig. 7-D) and
then hold down the number until
[DELETE COMPLETE] is displayed on
the LCD Panel.
（E）

★When shooting an excessively dark (bright) scene, for example, it is possible to
adjust the iris manually.
※It is necessary to change the camera menu setting [Scene File] in order to adjust the iris manually.
<Manual adjustment of the iris of AW-HE40 camera connected to CAM1 >
①Press the Button 1 at <CAMERA STATUS/SELECTION>. –(Fig. 8-A)
②Hold down the CAMERAOSD button –(Fig. 8-B) at the upper right of the panel to make the on-screen
menu –(Fig. 9) appear.
③Use F1 dial to change the following camera menu setting. –(Fig. 8-C)
Location: Camera ＞Scene ⇒Put the setting to any of [Manual1 –3].
④Press the “IRIS AUTO” button (*3) on the front panel to switch between Auto and Manual. –(Fig. 8-D)
(*3) When this button’s light is ON, it indicates Auto Iris. When it is OFF, it indicates Manual Iris
and the iris can be adjusted using IRIS dial. –(Fig. 8-E)
・ For details, please see the illustrated manual “Controlling Iris of AW-HE40 Camera
Manually”.
I want to adjust the iris manually.
Turn F1 →Select “Camera” →
Press F1
Press F1 →“Full Auto” blinks
（A）
（D）
（B）
（C）
Turn F1 →Select “Manual1” →
Press F1
（E）
(Figure 8: AW-RP50 Control Panel)
(Figure 9: On-Screen Menu)

★With Auto Focus, the focus may be difficult to be adjusted accurately depending on the
conditions.
In such a case, please switch the focus to the manual mode and try to adjust it manually.
<How to manually adjust the focus ofAW-HE40 camera connected to CAM1 >
①Press the Button 1 at <CAMERA STATUS/SELECTION>. –(Fig. 10-A)
②Press the “FOCUS AUTO” button (*4) on the front panel to switch between Auto and Manual. –(Fig.
10-B)
(*4) When this button’s light is ON, it indicates Auto Focus. When it is OFF, it indicates Manual Focus
and the focus can be adjusted using FOCUS dial. –(Fig. 10-C)
★When Focus Mode is [Manual], “Focus ADJ With PTZ (*5)” setting can be changed.
(*5) “Focus ADJ With PTZ” is a function to automatically readjust the focus while panning, tilting or
zooming.
If you need full manual control of focus, please have this setting at [Off]. ＊Default: [Off]
Location: System ＞Others ＞Other1/4 ＞Focus ADJ With PTZ ⇒[Off]
I want to adjust the focus manually.
Turn F1 →Select “System”
→Press F1
Turn F1 Select “Others”
→Press F1
（A）
（B）
（C）
Turn F1 →Select “Focus ADJ With PTZ”
Press F1 →[On] blinks
Turn F1 →Select [Off]
Press F1 →Setting determined
(Figure 10: AW-RP50 Control Panel)
(On-Screen Menu)
（Some weak points in AUTO Focus）
・Shooting far and close things at the same time
・Shooting an object surrounded by glittering things
・Shooting a low-contrast subject
・Shooting a fast-moving object
・Shooting through the dirty glass