5DISTANCE ADJUSTMENT
Step
1.
Turn the sensitivity adjuster fully.
BGS function: Counterclockwise
FGS function: Clockwise
2.
BGS function: In the object present
condition, turn the sensitivity ad-
MXVWHUDQGFRQ¿UPWKHSRLQW$ZKHUH
the sensor enters the sensing state.
FGS function: In sensing back-ground
condition, turn the sensitivity adjuster
DQGFRQILUPWKHSRLQW$ZKHUHWKH
sensor enters the non-sensing state.
3.
%*6IXQFWLRQ$IWHUUHPRYLQJWKHVHQV-
ing object, turn the sensitivity adjuster
DQGFRQ¿UPWKHSRLQW%ZKHUHWKHVHQ-
sor enters the non-sensing state.
FGS function: In the object present
FRQGLWLRQWXUQWKHVHQVLWLYLW\DGMXVWHUDQGFRQILUPWKH
point B where the sensor enters the sensing state.
If the sensor does not enter the “Light” state operation even when the
sensitivity adjuster is turned fully clockwise, the position is point B.
4.
7KHRSWLPXPSRVLWLRQWRVWDEO\GHWHFWREMHFWVLVWKHFHQWHUSRLQWEHWZHHQ$DQG%
6CAUTIONS
ƔThis product has been developed / produced for industrial use only.
ƔMake sure to carry out wiring in the power supply OFF condition.
Ɣ 7DNHFDUHWKDWZURQJZLULQJZLOOGDPDJHWKHVHQVRU
ƔVerify that the supply voltage variation is within the rating.
Ɣ ,ISRZHULVVXSSOLHGIURPDFRPPHUFLDOVZLWFKLQJUHJX-
ODWRUHQVXUHWKDWWKHIUDPHJURXQG)*WHUPLQDORIWKH
power supply is connected to an actual ground.
Ɣ ,QFDVHQRLVHJHQHUDWLQJHTXLSPHQWVZLWFKLQJUHJXODWRULQYHUWHU
PRWRUHWFLVXVHGLQWKHYLFLQLW\RIWKLVSURGXFWFRQQHFWWKH
IUDPHJURXQG)*WHUPLQDORIWKHHTXLSPHQWWRDQDFWXDOJURXQG
Ɣ ([WHQVLRQXSWRWRWDOPHDFKHPLWWHUDQGUHFHLYHURIWK-
UXEHDPW\SHRUOHVVLVSRVVLEOHZLWKPP
2
RUPRUHRI
conductor area cable. However , the extension of a power
supply line and the output line ofOHVVWKDQPLVDFFHSW-
DEOHLQFDVHXVLQJWKLVSURGXFWDVFRQIRUPLQJWR6PDUN
ƔMake sure that stress by forcible bend or pulling is not
applied directly to the sensor cable joint.
ƔDo not run the wires together with high-voltage lines or power lines or put
WKHPLQWKHVDPHUDFHZD\7KLVFDQFDXVHPDOIXQFWLRQGXHWRLQGXFWLRQ
Ɣ 'RQRWXVHGXULQJWKHLQLWLDOWUDQVLHQWWLPHPVDIWHU
the power supply is switched ON.
Ɣ 7DNHFDUHWKDWWKHVHQVRULVQRWGLUHFWO\H[SRVHGWRÀXRUHVFHQW
ODPSIURPDUDSLGVWDUWHUODPSDKLJKIUHTXHQF\OLJKWLQJGH-
YLFHRUVXQOLJKWHWFDVLWPD\DIIHFWWKHVHQVLQJSHUIRUPDQFH
ƔThis sensor is suitable for indoor use only.
ƔDo not use this sensor in places having excessive vapor, dust,
HWFRUZKHUHLWPD\FRPHLQFRQWDFWZLWKFRUURVLYHJDVHWF
Ɣ 7DNHFDUHWKDWWKHVHQVRUGRHVQRWFRPHLQFRQWDFWZLWKRLOJUHDVH
organic solvents such as thinner, etc., strong acid, or alkaline.
Ɣ 7KLVVHQVRUFDQQRWEHXVHGLQDQHQYLURQPHQWFRQWDLQ-
LQJLQÀDPPDEOHRUH[SORVLYHJDVHV
Ɣ 1HYHUGLVDVVHPEOHRUPRGLI\WKHVHQVRU
7RoHS DIRECTIVE
Ɣ 7KLVHTXLSPHQWFRPSOLHVZLWK5R+6(&DQG&KLQHVHGLUHFWLYH
Ɣ &KLQHVH5R+6LQGLFDWHVLQFOXVLRQGHVSLWHUHJXODWLRQYDOXH5HIHU&KLQHVHSDUW
BB
$
B
B
$
$$
<BGS> <FGS>
1
2
4
1
2
42SWLPXP
position
INSTRUCTION
MANUAL
$PSOL¿HU%XLOWLQ6PDOO3KRWRHOHFWULF6HQVRU
CX-44ȏ
WARNING
ƔNever use this product as a sensing device for personnel protection.
ƔIn case of using sensing devices for personnel protection, use
SURGXFWVZKLFKPHHWODZV DQGVWDQGDUGVVXFKDV26+$$16,RU
IEC etc., for personnel protection applicable in each region or country.
1
INTENDED PRODUCTS FOR CE MARKING
Ɣ 5HIHU³RXUZHEVLWHKWWSVSDQDVRQLFQHWLGSLGV[
JOREDO´IRUWKHLQWHQGHGSURGXFWV7KHPRGHOVOLVWHG
under ³ 63(&,),&$7,216´FRPHZLWK&(0DUNLQJ
$VIRUDOORWKHUPRGHOVSOHDVHFRQWDFWRXURI¿FH
2PART DESCRIPTION
2SHUDWLRQLQGLFDWRU2UDQJH
Lights up when the sens-
ing output is ON
2SHUDWLRQPRGHVZLWFK
L: Light-ON
D: Dark-ON
'LVWDQFHDGMXVWHU0XOWLWXUQ
Used when adjusting
distance
6WDELOLW\LQGLFDWRU*UHHQ
Lights up under the stable light
condition or the stable dark condition
ƔTurn the RSHUDWLRQPRGHVZLWFK gradually and lightly with
DÀDWKHDGVFUHZGULYHUSXUFKDVHVHSDUDWHO\
3MOUNTING
ƔThe tightening torque should be
1āPRUOHVV
Sensor
PRXQWLQJ
bracket
2SWLRQDO
0OHQJWKPP
screw with washers
4WIRING DIAGRAMS
ƔPNP output type
%URZQ9
%ODFN
Output
%OXH9
Load
-
12 to 24V DC
±10%
3LQN
1RWH
ƔNPN output type
%URZQ9
%ODFN
Output
%OXH9
Load
-
12 to 24V DC
±10%
3LQN
1RWH
1RWH7KLVLVVHQVLQJPRGHVHOHFWLRQLQSXW:LUH WKHVHQVLQJ PRGH
VHOHFWLRQLQSXWWRHLWKHU9EOXHRU9EURZQDQGVHOHFWWKH
VHQVLQJPRGH%*6)*6IXQFWLRQ
Function :LULQJ $SSULFDWLRQ
BGS function
:ULWHWR9Solid line
6HQVLQJREMHFWLVDSDUWIURPWKHEDFNJURXQG
FGS function
:ULWHWR9:ULWHWR
Sensing object contacts the background
Output operation is udes when detection-OFF
Technical Support - Application Assistance
or Place an Order - Contact Ramco
Ramco Innovations (800) 280-6933
www.sunx-ramco.com
