Panasonic FZ-N1 Series User manual

Operating I nstructions
Smart Handheld
EB-3901
Thank you for purchasing a Panasonic product.
Before operating this product, please read these instructions and
precautions, and save them for future use.
Tablet Computer
Model No. FZ-N1 series
Vous venez d’acquérir un produit Panasonic et nous vous
en remercions.
Avant d’utiliser ce produit, veuillez lire les présentes instructions
et précautions et les conserver pour usage ultérieur.
Operating Instructions - Read Me First...........................2
Refer to the Reference Manual by downloading from
the URL below
English
URL:- https://pc-dl.panasonic.co.jp/itn/manual/
Instructions d’utilisation - Lisez-moi.............................26
Reportez-vous au Manuel de référence en le
téléchargeant à partir de l’URL ci-dessous.
Français
N1mk2_Flat_NA_RMF_Draft1.0

2
Safety Precautions (English)
To reduce the risk of injury, loss of life, electric shock, fire,
malfunction, and damage to equipment or property, always
observe the following safety precautions.
Explanation of symbol word panels
The following symbol word panels are used to classify and
describe the level of hazard, injury, and property damage caused
when the denotation is disregarded and improper use is
performed.
The following symbols are used to classify and describe the type
of instructions to be observed.
Explanation of symbol word panels
Denotes potential hazards that will result
in serious injury or death.
Denotes potential hazards that could
result in serious injury or death.
Denotes potential hazards that could
result in minor injury.
This symbol is used to alert users to specific operating
procedures that must not be performed.
This symbol is used to alert users to specific operating
procedures that must be followed in order to operate the
product safely.
DANGER
WARNING
CAUTION

3Safety Precautions (English)
Battery
The battery is for use solely with this product. Do
not use it with any other products.
Electrolyte leakage, overheating, smoke, rupture, or fire
may result.
Charge the battery using the specified method.
Failure to do so may result in electrolyte leakage,
overheating, smoke, rupture, or a fire.
Do not throw the battery into a fire or expose it to
excessive heat.
Electrolyte leakage, overheating, smoke, rupture, or fire
may result.
Do not disassemble, modify, or insert sharp foreign
objects into the battery.
Electrolyte leakage, overheating, smoke, rupture, or fire
may result.
Do not short the positive (+) and negative (–)
contacts. Do not carry the battery around or store it
together with necklaces, hairpins, etc.
Electrolyte leakage, overheating, smoke, rupture, or fire
may result.
Keep the battery away from extreme heat, such as
fire and direct sunlight.
Failure to do so may result in electrolyte leakage,
overheating, smoke, rupture, or a fire.
Do not expose the battery to water or other liquids.
Electrolyte leakage, overheating, smoke, rupture, or fire
may result.
DANGER

4
Do not throw the battery or subject it to strong
impact such as dropping or applying high pressure.
Electrolyte leakage, overheating, smoke, rupture, or fire
may result.
• Stop using the product if the battery is subjected to
strong impact or if the battery is noticeably damaged
or deformed.
If the battery deteriorates, replace it with a new one.
Failure to do so may result in electrolyte leakage,
overheating, smoke, rupture, or a fire.
Do not directly touch electrolyte that has leaked
from the battery.
Electrolyte may enter the eyes and cause blindness, or
may come into contact with skin or clothing and cause
rashes.
• Flush with clean water without rubbing and seek
medical advice.
Do not place the battery in microwave ovens or
pressurized containers.
Sudden application of heat or pressure may damage the
battery, resulting in electrolyte leakage, overheating,
smoke, rupture, or a fire.
If the battery smells or leaks electrolyte, keep the
battery away from fire.
Failure to do so may result in electrolyte leakage,
overheating, smoke, rupture, or a fire.
WARNING

5Safety Precautions (English)
This product and charger
When using the product for extended periods, do
not expose your skin to the product for a prolonged
period.
Generated heat can cause low-temperature burns.
Do not disassemble, repair, or modify the product.
This may cause the battery to short circuit or overheat,
which may result in a fire or electric shock.
Do not insert foreign objects into the product.
This may cause the battery to short circuit or overheat,
which may result in a fire or electric shock.
Do not allow conductive materials such as metal
objects to touch the expansion bus connector.
This may cause a short circuit and overheating, which
may result in battery electrolyte leakage, overheating,
smoke, rupture, or a fire.
Do not place the product in microwave ovens or
electromagnetic cookers.
Doing so may cause overheating, smoke, or rupture,
which may result in a fire.
Do not touch the product or charger during lightning
storms if the product is connected to a charger.
There is a remote chance of electric shock.
WARNING

6
Do not turn the volume up too loud when using
headphones, etc.
Listening at high volumes for extended periods may
result in loss of hearing. Also, turn down the volume
before connecting headphones, etc. to prevent sudden
loud sounds.
Keep SD cards and SIM cards out of the reach of
infants and small children.
Small objects are suffocation and choking hazards. In
the event of accidental swallowing, seek medical help
immediately.
Do not operate the product while walking, driving,
riding a bicycle, etc.
Being distracted while engaging in these kinds of
activities can cause accidents or falls.
Do not use headphones, etc. while driving or in
potentially dangerous areas or situations.
Your inability to hear the sounds around you can cause
accidents. Take special care at rail crossings, station
platforms, roads, construction sites, etc.
Use only specified batteries.
Use of unspecified batteries may result in electrolyte
leakage, overheating, smoke, rupture, or a fire.

7Safety Precautions (English)
Immediately stop using the product if any of the
following occurs.
–Product is damaged
–Water or foreign objects enter the product
–Product emits smoke
–Product emits unusual smell or sound
–Product becomes unusually hot
Continuing use may result in a fire or electric shock.
Immediately turn the product off, disconnect it from the
power supply, remove the battery, and then contact your
technical support representative.
Close the headset jack cover and interface cover
when using the product near water or other liquids,
and in areas with a high concentration of moisture,
steam, dust, oily vapors, etc.
Foreign material that enters the product may cause fire
or electric shock. If foreign material enters the product,
turn the product off, disconnect it from the power supply,
and then remove the battery. Contact your technical
support representative for support or repair.
Stop using the product immediately and consult
your doctor if you feel any discomfort when staring
at flashing lights on the screen.
A very small percentage of individuals may experience
seizures or blackouts when exposed to certain light
patterns or flashing lights for extended periods.
Do not use the product near automatic control
equipment such as automatic doors, fire alarms, etc.
RF signals generated by the product may interfere with
the proper operation of such equipment.

8
Do not leave the product in areas with a high
concentration of moisture, steam, dust, oily vapors,
etc. for extended periods.
Foreign material that enters the product may cause a fire
or electric shock.
Do not move the product while the charger is
connected.
This may result in a fire or electric shock.
Make sure not to charge the product when it is wet.
This may result in a fire or electric shock.
Do not leave the product in extremely high
temperature environments for an extended period.
Leaving the product where it will be exposed to
extremely high temperatures, such as near fire or in
direct sunlight, may deform the product or cause
damage or malfunction to its internal components. Using
the product in these conditions may cause short circuit,
insulation defects, etc., which may in turn cause a fire or
electric shock.
Do not expose the skin to the product when using
the product in hot or cold environments.
Burns, low-temperature burns, or frostbite may result. If
direct contact with the skin is necessary, perform the
operation as quickly as possible.
Do not place the product on an unstable surface.
The product may drop, resulting in an injury.
Do not stack the product.
If balance is lost, the product may fall over or drop,
resulting in an injury.
CAUTION

9Safety Precautions (English)
Do not look directly at the light emitter or point the
flash at another person's eyes.
This may damage the eyes or cause temporary loss of
eyesight which could result in an accident.
Keep away from magnetic sources such as watches
and magnetic cards.
Failure to do so may cause data corruption or device
malfunction.
Do not expose the camera lens to direct sunlight for
extended periods.
This may result in a fire, burns, or injury due to the
converging effect of the lens.
For safety purposes, pull the plug when cleaning the
product or if you will not use it for extended periods.
Failure to do so may result in a fire or electric shock.
If a part such as the display is damaged, be careful
of broken glass or internal components that may
become exposed.
Failure to do so can cause injury.
Take a 10–15 minute break every hour when using
the product.
Using the product continuously for extended periods
may cause strain injuries and may have detrimental
health effects on your eyes, hands, or other parts of your
body.

10
Regulatory Information (English)
This pro duct and your heal th
This product, like other radio devices, emits radio frequency
electromagnetic energy. Because this product operates within the
guidelines found in radio frequency safety standards and
recommendations, we believe this product is safe for use by
consumers. These standards and recommendations reflect the
consensus of the scientific community and result from
deliberations of panels and committees of scientists who
continually review and interpret the extensive research literature.
In some situations or environments, the use of this product may
be restricted by the proprietor of the building or responsible
representatives of the organization. These situations may for
example include:
• Using this product on board of airplanes, or
• In any other environment where the risk of interference to other
devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of
wireless devices in a specific organization or environment (e.g.
airports), you are encouraged to ask for authorization to use this
product prior to turning on the product.
Information to the user
We are not responsible for any radio or television interference
caused by unauthorized modification of this product. The
correction of interference caused by such unauthorized
modification will be the responsibility of the user. We and our
authorized resellers or distributors are not liable for damage or
violation of government regulations that may arise from failing to
comply with these guidelines.
This product and your health
Information to the user

11Regulatory Information (English)
Additional safety precautions
Posted facilities
• Turn off the product when in hospitals, health care facilities, or
any facility where posted notices require you to do so.
Hospitals and health care facilities may be using equipment
that could be sensitive to external RF energy.
Pacemakers
• Medical device manufacturers recommend a minimum
separation of 15 cm between a wireless device and an
implanted medical device, such as a pacemaker or implanted
cardioverter defibrillator, to avoid potential interference with the
medical device.
• Persons with pacemakers:
– Should ALWAYS keep this product more than 15 cm from
their pacemaker when this product is turned ON;
– Should use the ear opposite the pacemaker to minimize the
potential for interference;
– Should not carry this product in a breast pocket;
– Should turn off the product immediately if there is any reason
to suspect that interference is taking place.
Hearing aids
• Some digital wireless products may interfere with some hearing
aids. In the event of such interference, consult the
manufacturer of your hearing aid to discuss alternatives.
Other medical devices
• If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately
shielded from external RF energy. Your physician may be able
to assist you in obtaining this information.
Additional safety precautions

12
Aircraft
• Turn off the product after boarding an aircraft, when instructed
by flight staff. Obey instructions from flight staff regarding the
use of the product in flight. Using this product in an aircraft may
be hazardous to the aircraft’s operation and disrupt wireless
communication, and may also be illegal.
Potentially explosive atmosphere
• Turn off the product in areas where a potentially explosive
atmosphere exists and obey all signs and instructions. Sparks
in such areas could cause an explosion or fire resulting in injury
or even death.
• Areas with potentially explosive atmosphere may include
fueling areas, chemical plants, below deck on boats, fuel or
chemical transfer or storage facilities, vehicles using petroleum
or natural gas, or areas where the atmosphere contains
particles such as grain, dust, or metallic powders, and any
other area where you would normally be advised to turn off
your vehicle engine.
Electronic devices
• This product receives and transmits radio frequency signals
while switched on. Most electronic equipment is shielded from
RF signals. However, certain electronic equipment may not be
shielded against the RF signals from this product. Therefore,
the use must be restricted in certain situations to avoid
interference.
Driving
• Give full attention to driving. Driving safely is your first
responsibility.
• Pull off the road and park before placing or answering a call. It
is unsafe to operate the product while driving.
• Check the laws and regulations in the areas where you drive,
and always obey them.

13Regulatory Information (English)
• Only qualified personnel should install the product in a vehicle.
Check regularly that the product is securely mounted in your
vehicle and operating properly.
• Do not place or install the product in the area over the air bag
or in the air bag deployment area. If the air bag inflates, serious
injury and/or damage could result.
• RF signals may affect improperly installed or inadequately
shielded electronic systems in motor vehicles. Consult the
manufacturer (or its representative) of the vehicle and any
equipment that has been added to the vehicle regarding the
use of mobile products.
• Use hands-free operation, if available and legally permitted.
Emergency communications
• Never rely solely on a mobile product for essential or
emergency communications. Network connections can be
affected by remaining battery level, radio signals, service
networks, and other conditions, and as a result, emergency
communications cannot be guaranteed in all conditions.
Antenna
• Do not replace the antenna. Unauthorized antennas,
modifications, or attachments could damage the product and may
violate regulations.
• Do not touch or cover the antenna area while the product is on.
Call quality, power levels, and the overall performance of the
product may be affected.
Volume
• Do not turn the volume up too loud when using headphones
and earphones.
• Exposure to excessive sound pressure levels for extended
periods may cause hearing damage.
• Being unable to hear sounds in your environment may lead to
accidents.

14
Intended use
• This product is not intended for use as, or as part of, nuclear
equipment/systems, air traffic control equipment/systems, aircraft
cockpit equipment/systems
*1
, medical devices or accessories
*2
,
life-support systems or other equipment/devices/systems that are
involved with ensuring human life or safety. Panasonic will not be
responsible for any liability resulting from the use of this product
arising out of the foregoing uses.
*1 Aircraft cockpit equipment/systems include Class 2 Electrical
Flight Bag (EFB) Systems and Class 1 EFB Systems when
used during critical phases of flight (e.g., during take-off and
landing) and/or mounted on to the aircraft. Class 1 EFB
Systems and 2 EFB Systems are defined by FAA: AC
(Advisory Circular) 120-76A or JAA: JAA TGL (Temporary
Guidance Leaflets) No.36.
*2 As defined by the European Medical Device Directive (MDD)
93/42/EEC.
• Panasonic cannot guarantee any specifications, technologies,
reliability, safety (e.g., Flammability/Smoke/Toxicity/Radio
Frequency Emission, etc.) requirements related to aviation
standards and medical equipment standards that differ from the
specifications of our COTS (Commercial-Off-The-Shelf) products.
• This product is not intended for use in medical equipment including
life-support systems, air traffic control systems, or other equipment,
devices or systems that are involved with ensuring human life or
safety. Panasonic cannot be held responsible in any way for any
damages or loss resulting from the use of this unit in these types of
equipment, devices or systems, etc. This product has been
designed so as to minimize shock to the LCD, the leakage of liquid
(e.g., water) on to the buttons, etc., but no warranty is provided
against such trouble. Therefore, as a precision instrument, be
extremely careful in the handling of the product.
Intended use

15Regulatory Information (English)
For USA
FCC Part 15 information
This product has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This product generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this product does cause harmful interference to radio or television
reception, which can be determined by turning the product off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and receiver.
• Connect the product to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC caution
To assure continued FCC emission limit compliance, use only
shielded interface cables when connecting to computer or peripheral
devices.
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
For USA

16
FCC RF exposure information
This product meets the government’s requirements for exposure to
radio waves. This product is a radio transmitter and receiver.
This product is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by
the Federal Communications Commission of the U.S. Government.
The guidelines are based on standards that were developed by
independent scientific organization through periodic and thorough
evaluation of scientific studies.
The standards include a substantial safety margin designed to
assure the safety of all persons, regardless of age and health.
The exposure standard for wireless handsets employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The
SAR limit set by the FCC is 1.6 W/kg.
The tests are performed in positions and locations (e.g., at the ear
and worn on the body) as required by the FCC for each model.
The highest SAR value for this product can be found under
Reference Manual of
https://pc-dl.panasonic.co.jp/itn/manual/
For body-worn operation, this product has been tested and meets
FCC RF exposure guidelines when used with a Panasonic accessory
designated for this product and when used with an accessory that
contains no metal and that positions the mobile device a minimum of
1.0 cm from the body.
Use of other accessories may not ensure compliance with FCC RF
exposure guidelines.
The FCC has granted an Equipment Authorization for this product
with all reported SAR levels evaluated as in compliance with the FCC
RF emission guidelines.
SAR information on this product is on file with the FCC and can be
found by searching for the product’s FCC ID number at
http://www.fcc.gov/oet/ea/fccid. To find the FCC ID number for
your product, first remove the battery pack. The FCC ID number
is printed on the nameplate underneath.

17Regulatory Information (English)
Wi-Fi
®
use
High power radars are allocated as primary users of the 5.25 to
5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can
cause interference with and/or damage this product.
Do not use in the vicinity of these high power radar systems.
Using hearing aids with mobile devices
When some wireless mobile devices are used near some hearing
devices (hearing aids and cochlear implants), users may detect a
buzzing, humming, or whining noise. Some hearing devices are more
immune than others to this interference noise, and mobile devices
also vary in the amount of interference they generate. In the event of
interference you may want to consult your hearing aid supplier to
discuss solutions.
The wireless telephone industry has developed ratings for some of
their mobile devices, to assist hearing device users in finding mobile
devices that may be compatible with their hearing devices. Not all
mobile devices have been rated. Mobile devices that are rated have
the rating on their box or label located on the box.
The ratings are not guarantees. Results will vary depending on the
user’s hearing device and hearing loss. If your hearing device happens
to be vulnerable to interference, you may not be able to use a rated
mobile device successfully. Trying out the mobile device with your
hearing device is the best way to evaluate it for your personal needs.
M-Ratings: Mobile devices rated M3 or M4 are likely to generate less
interference to hearing devices than mobile devices that are not
labeled. M4 is the better/higher of the two ratings.
T-Ratings: Mobile devices rated T3 or T4 are likely to be more usable
with a hearing device’s telecoil (“T-Coil Switch” or “Telephone Switch”)
than unrated mobile devices. T4 is the better/higher of the two ratings.
(Note that the hearing aid telecoil must be activated in order for it to
function, and that not all hearing devices have telecoils in them.)
Hearing devices may also be measured for immunity to this type of
interference. Your hearing device manufacturer or hearing health
professional may help you find results for your hearing device. The

18
more immune your hearing aid is, the less likely you are to
experience interference noise from mobile devices.
The HAC rating and measurement procedure are described in the
American National Standards Institute (ANSI) C63.19 standard.
Hearing aid compatibility
This mobile device has been tested and rated for use with hearing
aids for some of the wireless technologies that it uses. However,
there may be some newer wireless technologies used in this mobile
device that have not been tested yet for use with hearing aids. It is
important to try the different features of this mobile device thoroughly
and in different locations, using your hearing aid or cochlear implant,
to determine if you hear any interfering noise. Consult your service
provider or the manufacturer of this mobile device for information on
hearing aid compatibility. If you have questions about return or
exchange policies, consult your service provider or mobile retailer.
Responsible party
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102, USA
Support contact:
http://business.panasonic.com/support-computerstablets
Disposal
USA Only: Disposal may be regulated in your community due to
environmental considerations.
For disposal or recycling information, please visit Panasonic website:
https://www.panasonic.com/us/corporate/sustainability/eco.html or
call 1-888-769-0149.
TTY information
For hearing or speech impaired TTY users, call 1-877-833-8855
using a TTY device.

19Regulatory Information (English)
For Canada
Innovation, Science and Economic Development Canada
This device complies with Industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Wi-Fi use
This product (local network devices) for the band 5150-5250 MHz
is only indoor usage to reduce potential for harmful interference
to cochannel Mobile Satellite systems. High power radars are
allocated as primary users (meaning they have priority) of 5250-
5350 MHz and 5650-5850 MHz and these radars could cause
interference and/or damage to LE-LAN (licence-exempt local
area network) devices.
RF exposure information
This product complies with Industry Canada radiation exposure
limits set forth for an uncontrolled environment. This product is a
radio transmitter and receiver. It is designed and manufactured
not to exceed the emission limits for exposure to radiofrequency
(RF) energy set by Industry Canada. The guidelines are based on
standards that were developed by independent scientific
organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons, regardless of
age and health. The exposure standard for wireless handsets
employs a unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR limit set by Industry Canada is 1.6 W/kg.
The tests are performed in positions and locations (e.g., at the
ear and worn on the body) as required by Industry Canada for
each model.
For Canada

20
The highest SAR value for this product can be found under
Reference Manual of
https://pc-dl.panasonic.co.jp/itn/manual/
For body-worn operation, this product has been tested and meets
the RF exposure guidelines when used with a Panasonic
accessory designated for this product and when used with an
accessory that contains no metal and that positions the mobile
device a minimum of 1.0 cm from the body. Use of other
accessories may not ensure compliance with the RF exposure
guidelines.