Panasonic FZ-M1 Series User manual

Tablet Computer
Model No. FZ-M1 Series
Operating Instructions - Reference Manual
We recommend that this Reference Manual be printed.
Disclaimer
Computer specifications and manuals are subject to change without notice. Panasonic Corporation assumes no liability for damage incurred directly or
indirectly from errors, omissionsor discrepancies between the computer and the manuals. Refer for the latest information about optional products to the
catalogs, etc.
Trademarks
Microsoft, Windows, and the Windows logo are registered trademarks or trademarks of Microsoft Corporation of the United States and/or other
countries.
Intel, Core, and PROSet are either registered trademarks or trademarks of Intel Corporation.
microSDXC Logo is a trademark of SD-3C, LLC.
MobileMark®is a U.S. Registered Trademark of the Business Applications Performance Corporation.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarksor registered trademarksof HDMI Licens-
ing Administrator, Inc. in the United States and other countries.
Bluetooth®is a registered trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Panasonic Corporation.
Names of products, brands, etc., appearing in this manualare trademarksor registered trademarksof their respective own companies.
About the Software License
This product incorporates the following software:
(1) the software developed independently by or for Panasonic Corporation,
(2) the software owned by third party and licensed to Panasonic Corporation, and/or
(3) open source software
-1-

The software categorized as (3) is distributed in the hope that it willbe useful, but WITHOUT ANY WARRANTY, without even the implied warrantyof
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Please refer to the detailed terms and conditions thereof shown below.
About zlib
/* zlib.h -- interface of the 'zlib' general purpose compression library
version 1.2.8, April 28th, 2013
Copyright (C) 1995-2013 Jean-loup Gailly and Mark Adler
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use
of this software.
Permission is granted to anyone to use thissoftware for any purpose, including commercialapplications, and to alter it and redistribute it freely, subject to
the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a
product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly Mark Adler
[e-mail] [e-mail]
*/
About Lib PNG
This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is
included in the libpng distribution, the latter shallprevail.
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modifylibpng you may insert additional noticesimmediately following this sentence.
This code is released under the libpng license.
libpng versions1.2.6, August 15, 2004, through 1.6.3, July 18, 2013, are Copyright (c) 2004, 2006-2013 Glenn Randers-Pehrson, and are distributed
according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors
Cosmin Truta
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according
to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant
and with the following additions to the disclaimer:
There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the lib-
rarywill fulfillany of your particular purposes or needs. Thislibrary is provided with all faults, and the entire risk of satisfactory quality, performance,
accuracy, and effort is with the user.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn Randers-Pehrson, and are distributed accord-
ing to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik
libpng versions 0.89, June 1996, through 0.96, May1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and
license as libpng-0.88, with the following individuals added to the list of Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
Magnus Holmgren
Greg Roelofs
Tom Tanner
libpng versions 0.5, May1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 GuyEric Schalnat, Group 42, Inc.
For the purposes of thiscopyright and license, "Contributing Authors" is defined as the following set of individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
Paul Schmidt
Tim Wegner
-2-

The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including,
without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for dir-
ect, indirect, incidental, special, exemplary, or consequentialdamages, which may result from the use of the PNG Reference Library, even if advised of
the possibility of such damage.
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the fol-
lowing restrictions:
1. The origin of this source code must not be misrepresented.
2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.
3. This Copyright notice may not be removed or altered from any source or altered source distribution.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of thissource code as a component to supporting the
PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated.
A "png_get_copyright" function is available, for convenient use in "about" boxes and the like:
printf("%s",png_get_copyright(NULL));
Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.jpg (88x31) and "pngnow.png" (98x31).
Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative.
Glenn Randers-Pehrson
glennrp at users.sourceforge.net
July 18, 2013
GOVERNMENT RESTRICTED RIGHTS.
The Software is provided with “RESTRICTED RIGHTS.” Use duplication or disclosure by the government is subject to restrictions as set forth in
FAR52.227-14 and DFAR252. 227-7013 et seq. or their successors.
Use of the Software by the government constitutes acknowledgement of Intel’sproprietary rights therein.
Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA 95052.
Panasonic Corporation
Osaka, Japan
Web Site : https://panasonic.net/cns/pc/
© Panasonic Corporation 2018
PS0918-0
20170397ZAD
-3-

Introduction
Illustrations and Terminology in this Manual
This manual explains using the default setting.
Some illustrations and display examples may look different from the actual product.
Some types of software are automatically updated, and differences may occur from descriptions in this manual.
If you do not sign in as an administrator, you cannot use some functions or cannot display some screens.
Terms and illustrations in these instructions.
CAUTION: Conditions that may result in minor or moderate injury.
NOTE: Useful and helpful information.
The display of the key may be different from this manual according to the keyboard used. (e.g. “Delete” instead of “Del”)
Touch - :
This description instructs the user to touch (Start) first, and touch (Power) next.
<Only when connected to the external keyboard>
≪Enter≫: This means to press the ≪Enter≫key.
≪Alt≫+≪Del≫:
This means to press and hold ≪Alt≫key, and then press ≪Del≫key.
In these instructions, the names are referred as follows.
“Windows 10 Pro” as “Windows” or “Windows 10”
“Multilanguage User Interface” as “MUI”.
The computer screen supporting touching methods (your fingers) is referred to as the “screen”.
In thismanual, microSIM card iscollectively referred to as SIM card.
Regarding Windows 10
Tablet mode and Desktop mode
Windows 10 offers the tablet mode optimized for the touch panel operation, and also the desktop mode in which operation isperformed using the key-
board and touch panel.
The mode can be switched by touching (Notification), and then touching (Tablet mode).
N O T E
nDisplaying the task tray notification icons ( ) in tablet mode.
1. Touch and hold on an empty location on the task bar.
2. Touch [Show all notification icons] on the menu that appears.
appears on the tasktray. Touch to displaythe notification icons.
Screen messages
Screen messages are explained in [English (United States)].
-4-

(Depending on the language preference, some screen messages in these instructions are different from the actualscreen messages. For example,
[Flight mode] may be displayed instead of [Airplane mode] in some language preference)
Displaying Apps
1. Touch (All apps).
Alternatively, touch (Start) at the bottom left corner in the desktop mode.
Opening the Control Panel
On the Start screen, proceed as follows.
1. Touch (All apps) - [Windows System] - [Control Panel].
Alternatively, touch (Start) - [Windows System] - [ControlPanel] in the desktop mode.
Opening the “Settings” screen
1. Touch (Settings).
Alternatively, touch (Start) - (Settings) in the desktop mode.
Opening the Panasonic PC Settings Utility
On the Start screen, proceed as follows.
1. Touch (Panasonic PC Settings Utility).
Alternatively, touch (Start) - (Panasonic PC Settings Utility) in the desktop mode.
Notification area
The notification area ison the right side of the screen.
To display the notification, touch (Notification) on the task tray.
Latest Information on Windows 10
When Windows 10 is updated, the screen display or operation procedures may be changed.
For the latest information on Windows 10, see the following web page.
https://pc-dl.panasonic.co.jp/itn/addendum/
Sound and Video
Sound (e.g. MP3, WMA) and video (e.g. MPG, WMV) recorded in microSD Memory Card may be interrupted during playback. If this
happens, copy them to the flash memory drive and play back.
Depending on the processing status on Windows, sound may be interrupted at Windows startup. You can mute the sound at startup.
The startup sound is muted as the factory default.
1. Touch and hold (Speaker) on the task tray, and touch [Sounds].
2. Remove the check mark from [Play Windows Startup sound], and touch [OK].
When high-frequency sound occurs
If high-frequency sound occurs while using the computer, check the settings for the USB power saving function.
-5-

Set [USB selective suspend setting] to [Enabled].
1. Touch (Settings) - [System] - [Power & sleep] - [Additional power settings].
Alternatively, touch (Start) - (Settings) - [System] - [Power & sleep] - [Additional power settings] in the desktop mode.
2. Touch [Change plan settings] of the current power plan.
3. Touch [Change advanced power settings].
4. In [Advanced settings], double-touch [USB settings].
5. Double-touch the displayed [USB selective suspend setting].
6. Change settings of [On battery] and [Plugged in] to [Enabled].
7. Touch [OK] and exit the “Power Options” screen.
About the Ambient Light Sensor
The ambient light sensor is used to adjust the display screen brightness automatically.
To configure the automatic adjustment function, proceed as follows.
1. Touch (Settings) - [System] - [Display].
Alternatively, touch (Start) - (Settings) - [System] - [Display] in the desktop mode.
2. Add the check mark to [Change brightness automatically when lighting changes] under “Brightness and color”.
Windows Update
You can update to the latest patchesand service packs for Windows with the following menus.
1. Touch (Settings) - [Update & Security] - [Windows Update].
Alternatively, touch (Start) - (Settings) - [Update & Security] - [Windows Update] in the desktop mode.
2. Touch [Check for updates].
Do not apply “Driver Updates” even if a message to update a driver appears. If a driver update is required, contact your technical support office.
-6-

Create a Recovery Disc
You can make a recovery disc for preinstalled software.
The recovery discreturns the flash memory to the factory default. To create a backup of the recent state of the flash memory, refer to Flash Memory
Backup/Restore Function.
Preparation
Blank discs (About usable types of discs and required numbers of discs, refer to the screen.) or USB storage device.
When using DVD media to create a recovery disc, prepare the commercially available optical drive.
USB memory device can also be used as a recovery disc.
Connect the AC adaptor and do not remove it until the operation is complete.
Close all applications except for this utility.
Remove allperipherals (excluding the device that will be used to create the recovery disc).
Turn off the wireless function.
N O T E
nIf the recovery partition is deleted, you cannot create recovery disc(s).
<When using a USB storage device to create a recovery disc>
nAny previously existing data stored on the USB storage device willbe deleted.
nUSB storage devices with capacities insufficient for creating a recovery disc cannot be used.
nUSB storage devices that are partitioned cannot be used.
nUSB storage devices that are recognized as SCSI (i.e., UASP*1 devices) cannot be used.
*1 : USB Attached SCSI Protocol.
CAUTION
nUSB memory device can also be used as a recovery disc.
nDo not perform the following operations until creating the recovery disc is complete.
Shut down or restart Windows.
Enter sleep or hibernation.
Remove the commercially available optical drive or USB storage device being used for recovery disc creation.
nIf you interrupted creating a recovery disc, a message of failure may appear in step 10 screen below. In this case, restart the com-
puter, and create a new recovery disc again.
1. Sign in to Windows as an administrator.
2. Connect the device being used to create the recovery disc to the unit.
For DVD media
1. Connect the commercially available optical drive to the USB Port.
2. Insert the disc into the commercially available optical drive.
For USB storage devices
1. Connect the USB storage device to the USB port.
3. Touch (Panasonic PC Recovery Disc Creation Utility).
If the “User Account Control” screen appears, touch [Yes].
4. Touch [Next].
5. Confirm on-screen information ([Select OS Image] and [Number of discs required]), and then touch [Next].
6. Select the drive, and in the case of DVD media, select the disc type.
7. Touch [Next].
8. In the case of DVD media, select the [Write speed].
-7-

9. Touch [OK]
Creation of the recovery disc (i.e., writing) starts. Wait a moment for the processto complete.
10. Finish creation of the recovery disc as follows.
For DVD media
1. Remove the disc when “Recovery disc #1 complete.” appears, and label the disc to avoid losing it.
Do not use sharp objects that may leave a mark.
2. If the recovery disc spans multiple discs, insert the next disc.
3. Touch [OK].
4. Follow the on-screen instructionsto create allthe recovery discs.
5. Touch [OK] on the “All recovery discs complete.” screen.
For USB storage devices
1. Touch [OK] on the “All recovery discs complete.” screen.
2. Perform “Safely Remove Hardware and Eject Media”, and remove the USB storage device.
N O T E
nThe disc created with this utility is only for this computer. You cannot use for others.
nAdditional applications cannot be recovered even if you use a recovery disc created with this utility.
nIf you fail to create a recovery disc or an error message appears, try either of the following procedures.
Insert the disc or USB storage device correctly.
Check the disc or USB storage device condition.
Restart the computer and try to create a recovery disc again.
Contact Panasonic Technical Support.
-8-

About the Partition Structure
CAUTION
nDo not add or delete partitions in Windows 10, as the Windows area and recovery partition must be adjacent to each other in Windows
10.
-9-

Flash Memory Backup/Restore Function
Panasonic Corporation will bear no responsibility for any damage suffered (including loss of data) as a result of the use of this function.
Creating a Backup of the Flash Memory Data
You can create a backup of the flash memorydata, which can be used to recover from hardware failure.
This function creates a backup of the recent state of the flash memory. To return the factory default, use a recovery disc. ( Create a Recovery Disc)
To create a backup of the flash memory to another storage media (e.g., external hard disk).
Connect the storage media, and follow the steps below.
1. Open the Control Panel, and then touch [System and Security] - [File History].
2. Touch [System Image Backup].
3. Touch [Create a system image].
Follow the on-screen instructions.
N O T E
nConnect the AC adaptor and do not remove it until backup is complete.
Restoring the Flash Memory Data
1. Touch (Settings) - [Update & Security] - [Recovery].
2. Touch [Restart now] under “Advanced startup”*1.
3. Touch [Troubleshoot] - [Advanced options].
4. Touch [System Image Recovery].
Follow the on-screen instructions.
*1 : Screen messages are explained in [English (United States)].
(Depending on the language preference, some screen messages in these instructions are different from the actualscreen messages. For example,
[Advanced start-up] may be displayed instead of [Advanced startup] in some language preference.)
-10 -

Description of Parts
Front side
A. Wireless WAN Antenna
<Only for model with wireless WAN>
(Wireless WAN)
B. Wireless LAN Antenna / Bluetooth Antenna
<Only for model with wireless LAN>
<Only for model with Bluetooth>
(Wireless LAN)
(Bluetooth)
C. Ambient Light Sensor
The ambient light sensor isequipped with an automatic brightness adjustment function that adjusts the display screen. ( Automatic bright-
ness adjustment)
D. Front Camera
(Camera)
a. Camera Lens
b. Camera Indicator
E. LED Indicators
: Power Indicator
Off: Power off/Hibernation, Green: Power on, Blinking green: Sleep.
: Drive Indicator (Drive status)
: Battery Indicator (Battery status)
(When the battery indicator does not light on)
(Battery Power)
F. GPS Antenna
<Only for model with wireless WAN / dedicated GPS / GPS on wireless WAN>
(GPS)
G. Wireless LAN Antenna
<Only for model with wireless LAN>
(Wireless LAN)
H. Windows Button
(Tablet Buttons)
-11 -

Top
A. Microphone
B. Volume Button
(Tablet Buttons)
C. Power Switch
D. Rotation Lock Button
(Display Rotation)
E. A Button
(Tablet Buttons)
Bottom
A. Security Slot
A Kensington cable can be connected.
For further information, read the manual that comes with the cable.
B. Expansion Bus Connector
(Cradle)
C. External Antenna Connector
<Only for model with wireless WAN>
Left side Right side
A. DC-IN Jack B. USB 3.0 port
(USB Devices)
C. Headset Jack
A headset or headphone can be connected.
Rear side
-12 -

A. Rear Camera
(Camera)
a. Camera Lens
b. Camera Indicator
c. Camera Light
B. Speaker
C. Battery Indicator
<Only for model with Built-in Bridge Battery>
D. Battery Latch
(Battery Power)
E. Battery Pack
F. microSIM Card Slot
<Only for model with wireless WAN>
(Wireless WAN)
G. microSD Memory Card Slot
(microSD Memory Card)
Top (optional)
A. Barcode Reader / Serial Port (Only for FZ-M1J-series models) / LAN Port
<Only for model with Barcode Reader>
(Barcode Reader)
<Only for FZ-M1J-series models>
<Only for model with Serial Port>
(Serial Port)
<Only for model with LAN Port>
(LAN)
B. Built-in Bridge Battery
<Only for model with Built-in Bridge Battery>
C. Smart Card Reader / Magnetic Stripe Card Reader / Contactless Smart Card Reader
<Only for model with Smart Card Reader>
(Smart Card)
<Only for model with Magnetic Stripe Card Reader>
(Magnetic Stripe Card Reader)
<Only for model with Contactless Smart Card Reader>
(Contactless Smart Card Reader/RFID Reader)
-13 -

Rear side (When installed options)
A. 3D camera
<Only for model with 3D camera>
B. Thermography Camera
<Only for model with Thermography Camera>
-14 -

Turning On / Turning Off
Turning On
Press and hold the power switch untilthe power indicator lights. ( Description of Parts)
N O T E
n<Only for FZ-M1G-series models>
The LED may turn off for a few seconds immediately after the computer is turned on. This is not a malfunction.
nDo not press the power switch repeatedly.
nThe computer will forcibly be turned off if you press and hold the power switch for four seconds or longer.
nOnce you turn off the computer, wait for ten seconds or more before you turn on the computer again.
nDo not perform the following operation until the drive indicator turns off.
Connecting or disconnecting the AC adaptor
Pressing the power switch
Touching tablet buttons, screen or external mouse
Turning Off
Shut down the computer.
1. Touch (Start) at the bottom left corner.
2. Touch (Power) - [Shut down].
N O T E
To turn off the computer completely, proceed as follows.
1. Touch (Settings) - [Update & Security] - [Recovery].
2. Touch [Restart now] under “Advanced startup”.
3. Touch [Turn off your PC].
Precautions against Starting Up/Shutting Down
Do not do the following
Connecting or disconnecting the AC adaptor
Pressing the power switch
Touching tablet buttons, screen or external mouse
N O T E
-15 -

nTo conserve power, the following power saving methods are set at the time of purchase.
The screen automatically turns off after :
10 minutes (when AC adaptor is connected) of inactivity
5 minutes (when operating on battery power) of inactivity
The computer automatically enters sleep*1 after :
20 minutes (when AC adaptor is connected) of inactivity
15 minutes (when operating on battery power) of inactivity
*1 : Refer to “Sleep/Hibernation Functions” about resuming from sleep.
-16 -

Screen Input Operation
The screen of your computer allows you to perform the same operations as a mouse by touching its surface.
The computer supports, using your fingers and the dedicated pen (optional).
N O T E
nThis computer has adopted a capacitance type touch screen. Note that the touch screen may respond to the following:
Putting the dedicated pen (optional) or finger close to the screen.
Liquid or metallic objects other than the dedicated pen (optional) or finger.
To operate ”touch and hold”
Touch and hold the object with your fingers, or the dedicated pen (optional), and release it when a flame surrounding the object appears.
Using the dedicated pen (optional)
We recommend placing the dedicated pen (optional) perpendicular to the screen surface when using it.
Press the dedicated pen's tip on the screen surface, and use the pen.
Operation by touching the screen
Instead of operating the screen with the pointer, you can use your fingers.
This computer supports multitouch of ten points or less at the same time.
Touch (Tap) Touch the screen once with one finger.
Spread / pinch Touch an image or document with two fingers, and spread your fingers apart
to zoom in or pinch them together to zoom out.
-17 -

Drag Touch an object (file, icon, etc.) and drag your finger to the desired location
before removing it to move the object.
Swipe Touch with a sweeping motion.
Flick Touch with a quick sweeping motion.
CAUTION
nTouch the screen with your fingers or the dedicated pen (optional).
When touching the screen, use only your fingers or the dedicated pen (optional) on the surface.
Touching the screen with objects (e.g. fingernail, metallic object, or other hard or sharp objects) other than specified may scar or stain the sur-
face, causing malfunction.
nDo not apply too much pressure when operating the screen.
Only a light touch is required to operate the screen. Applying too much pressure may damage the surface.
nDo not operate the computer when such things as dust are on the screen.
Do not allow contact with substances that could dirty the screen, such as oil.
Touch Screen Mode
You can select the suitable operation mode in Touch Screen Mode.
1. Touch (Panasonic PC Settings Utility) - (Settings) - (Touch Screen).
2. Select the operation mode under “Touch Screen Mode”.
[Pen] mode
Suitable for the dedicated pen (optional) operation.
Use this mode when not operating with finger.
Using this mode may cause accidental response to metal objects close to the screen.
Unless you have the dedicated pen (optional), operation will not be possible.
[Pen/Touch] mode
Use this mode when using both finger and the dedicated pen (optional).
If both the dedicated pen (optional) and finger touch the screen at the same time, the dedicated pen (optional) operation takespriority.
Using this mode may cause accidental response to metal objects close to the screen.
[Touch] mode
Suitable for finger operation.
Use this mode when not operating with the dedicated pen (optional).
[Touch (Glove)] mode
Use this mode when operating with a glove on.
Depending on the type of glove, operation may be ignored.
With finger operation, the screen may not respond properly.
[Touch (Water)] mode
Use this mode when the screen or finger iswet with water drops in operation.
Depending on the water drop condition, operation may be ignored.
3. Select the “Windows button in Touch (Water)”.
-18 -

[Enable]: The (Windows Button) is enabled even when “Touch Screen Mode” is set to [Touch (Water)].
[Disable]: The (Windows Button) is disabled when “Touch Screen Mode” is set to [Touch (Water)].
4. If a confirmation message appears, touch [Yes].
N O T E
nYou cannot use the pen regardless of the setting before Windows is started up.
nYou cannot use the pen with the operations other than the Windows (PIN input of Bitlocker, operating screen from Recovery Drive,
etc.) even if the pen operation mode is set.
nWhen “Touch Screen Mode” is set to [Touch (Water)], multi touch input is reduced to 2 points.
nWhen “Touch Screen Mode” is set to [Touch (Water)], the (Windows Button) is disabled.
You can keep the setting as [Enable] even if the default setting is [Disable] on “Windows button in Touch (Water)”.
Settings can be made by using the Panasonic PC Settings Utility.
nYou can reset the touch screen by pressing Windows button when the touch screen cannot be used or the pen cannot be used in the
[Pen] / [Pen/Touch] mode.
Calibrating the Screen
Pen input and touch input are properly configured under default settings, so calibration isnot necessary under normal circumstances.
If accurate pen input or touch input is no longer possible after changing the LCD resolution, for example, perform calibration as follows.
CAUTION
nChange the display mode to the landscape before starting screen calibration. If calibration is performed other than the landscape, it
may not be possible to touch the target marks correctly.
N O T E
nAt first, sign in to Windows as an administrator, and perform this calibration.
1. Set the touch screen mode to [Pen] / [Pen/Touch] / [Touch]. ( Touch Screen Mode)
2. Open the Control Panel, and then touch [Hardware and Sound] - [Tablet PC Settings].
3. Touch [Calibrate].
If [User Account Control] is displayed, touch [Yes].
4. Using your finger or the dedicated pen (optional), touch each of the “+” target marks one by one, and then touch [Yes].
N O T E
nWhen using the dedicated pen (optional), make sure dedicated pen (optional) isperpendicular to the screen to get the most accurate cal-
-19 -

ibration.
CAUTION
nIf you perform calibration as a standard user, the calibration data is valid untilyou sign out (the data becomes invalid after you have signed out).
When using the computer continuously, perform calibration as an administrator.
nIf you cannot operate the computer correctly after calibration, delete the calibration data by touching [Control Panel] - [Hardware and Sound] -
[Tablet PC Settings] - [Reset], and perform calibration again. (Be sure to delete the calibration data as an administrator.)
N O T E
nThe following message, “Right-click anywhere on the screen to return to the last calibration point. Press the Esc button to close the
tool.” will appear on the center of the screen during calibration. However, the operation to close the tool by pressing the ≪Esc≫key
can be performed only when an external keyboard is connected.
nIf you cannot touch the desired position, perform calibration again and restart the computer.
About Touch Operation Support
Touch Operation Support is an application that allows you to perform screen operationsmore easily. When you use a two-finger tap gesture to specify the
area in which you want to perform touch operations, the area is displayed in a zoom window, allowing you to perform touch operations in an expanded dis-
play.
Using Touch operation support settings
Important usage notes
This application will only operate on internal screen displays.
Using the two-finger tap gesture may not display the zoom window in certain applicationsthat handle touch operations independently (e.g.,
Microsoft Office Word, Internet Explorer and Paint).
This application may take some time to start after sign in.
You cannot use the two-finger tap gesture to display the zoom window unless this application is running.
Using the two-finger tap gesture willnot display the zoom window in some applications (Magnifier (Windows), Touch Keyboard (Windows), On-
Screen Keyboard (Windows), etc.).
Expanding a portion of the display
When you use a two-finger tap gesture to specify the area in which you want to perform touch operations, the area is displayed in a zoom window, allow-
ing you to perform touch operations in an expanded display.
Opening the zoom window
1. Perform a two-finger tap on the area of the screen you want to expand.
A rectangular zoom window with a diagonallength equal to the distance between the two tapped pointsappears.
(1) Perform two-finger tap. (2) Display expands.
-20 -