Panasonic EASA-PHONE KX-T123211D Owner's manual

EIA/REMOTE
PROGRAMMING
MANUAL ’
KX-T123211 D
ELECTRONIC MODULAR SWITCHING SYSTEM
Please read before use.

Preface
KX-Tl23211 D EMSS has function that programming or
reprogramming (Showing, Editing, Dumping so on) can be done by
using a RS-232C interface port or a MODEM (through a Central
Off ice) from the place where KX-Tl23211 D is set and far.
n
The Card which should be installed to KX-Tl23211 D consists of
the following cards.
0 Direct Inward System Access Cards KX-T123291
0 MODEM Card KX-T123296
n When use the RS-232C interface port (On-site Administration)
n
Programming or reprogramming can be done by connecting it to If Outgoing Message is sent when a call is sent to
KX-Tl23211 D,
KX-T123211 D at the same place as it. you will be able to confirm that the call arrived to the other party,
so this card is useful.
0 Outgoing Message Card KX-T123292
n
Data terminal equipment
n When use the MODEM (Remote Administration)
Programming or reprogramming can be done through a Central
Office from the place where KX-Tl23211 D is in a few handreds
miles away.
Data terminal equipment
Telepone Line
KX-T1232 11 D
.; 7
- 1
Data terminal equipment
We recommend a data terminal equipment provided with a display
(Example KX-D4985 Panasonic).
A data terminal which is not equipped with a display can print out a
data automatically, so this can be used, too.
\
‘Lit.- ;
--.,’

Feature
Edit 1 Shqw
Program to KX-T123211 D newly or the preset programming
contents are displayed on the display of the data terminal
equipment and then confirm (by show mode) or change (by edit
mode) them.
H Dump
The preset program data in KX-T123211 D can be copied to the
floppy disk in a disk drive of a data terminal equipment.
n System Working Report
Interactive Style
Showing or Editing of data is done with a conversation style like
that after one person ask, the other person answer.
The number of incoming calls, answered of incoming calls and
unanswered of incoming calls and the number of access
’
requested, access succeeded and access failed are reported.
Batch Style
After store the data which is preset or wish to change with a
floppy, the data can be transmitted to KX-Ti 23211 D at a time and
program can be done.
When a data is entered at a time at the place where
KX-T123211 D is set, RS-232C interface port is used and when a
data is entered from far, send a data at a time after call the other
w-W
II
In this Manual, the model No. KX-T123211 D is abbreviated to
KX-T123211.
l-2

Contents
Outline of the Operation ............................. 3-l
Preparation
On-site Administration .......................... 3-2
Remote Administration ........................... 3-3
On-site / Remote Administration Start
On-site Administration Start ...................... 3-4
Remote Administration Start ....................... 3-4
On-site / Remote Administration Start Map ........... 3-5
On-site / Remote Administration End
On-site Administraion End ....................... 3-8
Remote Administraion End ........................ 3-8
On-site / Remote Administraion End Map ........... 3-7
To Edit the Data by “lntaractive Style” .................. 3-8
Editing or Programming .......................... 3-g
To Show the Data by “Interactive Style” .............. 3-l 1
Showing .................................... 3-l 2
To Edit or Show the Data by “Batch Style” ............ 3-13
To make the batch data ........................ 3-15
Edit / Show Mode Map ............................ ‘$17
To Dump the Data ............................... ‘J-1 8
Dump Mode Map ............................. ‘J-20
.
To Dump or Clear the System Working Report (SWR)
System Working Report Map . . . . . . . . . . . . . .
Example of Programming
To edit the data by “Interactive Style”
with Remote Administration . . . . . . . . . . . . . . . .
The way of seeing table
. . . . . . . . . . . 9 . . . . . . .
. .
. .
. .
. . 3-21
. . .
3-22
. . . . .
4-l
. . . . .
4-3
2-1
Format
SYSTEM FEATURE-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-l
0 Extension Number Assignment-l (for Jack number 01 through 16)
SYSTEM FEATURE-2 . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
0 Extension Number Assignment-2 (for Jack number 17 through 32)
SYSTEM FEATURE-3 . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
0 System Speed Dialing Entry
SYSTEM FEATURE-4 . . . . . . . . . . . . . . . . . . . . . . . . . . 543
0 Date and Time Setting
0 Operator Assignment
0 Automatic CO Hold Using DSS Button
0 Day/Night Service Mode
0 Call Hunting
SYCJ-EM FEATURE-5 . . . . . . . . . . . . . . . . . . . . . . . . . . 543
0 Area Type Selection
0 CO Operator Call Boundary Class
0 Toll Restriction of System Speed Dialing
SYSTEM FEATURE-6 . . . . . . . . . . . . . . . . . 5-g
l Toll Restriction-Allowable Exchange Code Selection
SYSTEM FEATURE-7 . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
0 Toll Restriction-Area Code Entry for Class 3
SYSTEM FEATURE-8 . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
0 Toll Restriction-Exchange Code Entry for Class 5
SYSTEM FEATURE-9 . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
0 Toll Restriction-Exchange Code Entry for Class 7

SYSTEM FEATURE-10 . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
0 Hold Time Reminder
0 Hold Recall Time Set
0 Transfer Recall Time
0 Call Forwarding Starting Time
0 Pickup Dial Delay Time
l CO to CO Duration Time Limit
0 Off Premise Extension (OPX)
0 Off Hook Call Announcement (OHCA)
l Call on Hold for Standard Telephone
SYSTEM FEATURE-1 1 . . . . . . . . . . . . . . . . . .
0 SMDR Parameters
0 Incoming/Outgoing Call Selection for printing
0 Secret Speed Dial / One Touch Dial Printing
0 Duration Time Count Start Mode
0 External Paging Access Tone
0 DTMF Receiver Check
SYSTEM FEATURE-1 2. . . . . . . . . . . . . . . . . .
Direct Inward System Access (DISA)
SYSTEM FEATURE-13 . . . . . . . . . . . . . . . . . .
0 Day/Night Service Mode (Starting Time)
SYSTEM FEATURE-90 . . . . . . . . . . . . . . . . .
0 RS-232C Communication Parameters
. . .
. . .
. 5-15
. 5-19
. 5-20
OUTSIDE LINE FEATURE-1 . . . . . . . . . . . . . . . . . . . . . . . . 6-l
0 CO Connection Assignment
0 Dial Mode (DTMF/PuIse/CalI Blocking)
0 Host PBX Access Codes Assignment
0 Trunk Group Assignment
0 Automatic Designated CO Line Access
0 CO Mode (Normal / Direct In Line / Direct Inward System
Access) Assignment
0 Pause Time Assignment
0 Hookswitch Flash Timing
0 Calling Party Control (CPC) Signal
0 Disconnect Time
CPC Signal Detect Time . . . . . . . . . . . . . . . . . . . . . . . . G-3
OUTSIDE LINE FEATURE-2M
. . . . . . . . . . . . . . . . . . . . . . 6-4
0 Flexible Outward Dialing Assignment (Day/Night Mode)
OUTSIDE LINE FEATURE-4/5 . . . . . . . . . . . . . . . . . . . . . . 6-5
0 Flexible Ringing Assignment (Day/Night Mode)
OUTSIDE LINE FEATURE-fj/T . . . . . . . . . . . . . . . . . ..+343
0 Delayed Ringing Assignment (Day/Night Mode)
EXTENSION FEATURE-1 . . . . . . . . . . . . . . . . . . . . . . . . . . .7-l
0 Extension Group Assignment
0 Service Class Assignment of Toll Restriction
0 Extension Name
0 Account Code Input Mode
0 Call Transfer to Outside Line
0 Call Forwarding to Outside Line
0 Executive Override
0 Do not Disturb Override
2 --2

Contents (cont.)
EXTENSION FEATURE-2 .......................... 7-3
0 Flexible CO Button
DOORPHONE FEATURE-l/2 ....................... 8-l
0 Ringing Assignment of Doorphone (Day/Night Mode)
DSS CONSOLE FEATURE-1 ....................... g-1
0 Paired Telephone Assignment for DSS Console
DSS CONSOLE FEATURE-2/3 ..................... 9-2
@ DSS Console 1 or 2-Flexible DSS Button
CLEAR FEATURE ..............................
10-l
Programming Table .............................
11-l
Supplement
Kinds of Setting Mode Command and Prompt ....... 12-1
Disposal Style ...............................
12-l
Note ....................................... 12-l
“HLP” Command .............................
12-l
Main Command System ........................
12-2
DisposalExecuteCommand
.....................
12-2
The way to enter Disposal Execute Command ....... 12-3

Outline of the Operation
To edit or show the system program To dump the system data or system working report
Preparation See pages 3-2 and 3-3. Preparation See pages 3-2 and 3-3.
Start
See page 3-4.
Start See page 3-4.
Mode Selection
Edit / Show mode
0 Interactive Style
0 Batch Style
See pages 3-8
through 3-17.
End
Item Selection
1 Programming 1See pages 5-1
through 10-l.
See page 3-6.
See pages 3-18
through 3-22.
End
See page 3-6.

On-site / Remote Administration Start
1. Set the System Program Switch on the KX-Tl23211 to the “EIA”
position.
The display on data terminal will show ;
; Welcome to KX-Tl23211 on-site administration
I
ver 2.0 Panasonic CO., LTD
; ** Jan. 1. 1988 12:OO’AM **
3. After the answer carrier tone, set the on-line mode on your data
terminal equipment.
l The display on data terminal will show.
; The “HLP” displays command informations ; Welcome to KX-Tl23211 remote administration
1ver 2.0 Panasonic CO., LTD
; ** Jan. 1. 1988 12:OO’AM ** ; ** Jan. 1. 1988 12:OO’AM **
; The “HLP” displays command informations’; The “HLP” displays command informations’
l---d l---d
; > L-1 ; > L-1
n When you set the programming switch to the “EIA” position, the
system will stop its own normal exchanging operations, disconnect
all the current calls, and connect same extensions to CO lines
directly with the power failure transfer feature.
CO1 will be assigned to extension of jack number 01
CO2 will be assigned to extension of jack number 02
CO5 will be assigned to extension of jack number 09
CO6 will be assigned to extension of jack number 10
CO9 will be assigned to extension of jack number 17
CO1 0 will be assigned to extension of jack number 18
0 Be sure the System Program switch on the KX-Tl23211 is set to
the “SET” position.
1. Make a call to the line which is beforehand programmed as a DISA
Line on the KX-Tl23211.
0 Dial tone will be heard.
0 If the Outgoing Message Card is installed to KX-Tl23211,
Outgoing Message will be heard instead of dial tone.
2. Dial the Remote Security Code (70000 through 79999).
You will hear the answer carrier tone.
0 Whenever you don’t know which commands should be entered next,
press “HLP” and Carriage Return Keys. You will find the next
command (See page 12-l).
3-4
3-2

On-site administration
Set the System
Program Switch
to the “EIA”
Remote administraion
communication
I:
Indication on
display of data
terminal .
eqipment
; Welcome to KX-T123211 on-site administration ; Welcome to KX-T123211 remote administration
ver 2,0 Panasonic CO., LTD ; ver 2.0 Panasonic CO., LTD
I I I
1; ** CurCent ;ime ** 1
; The “HLP” displays command informations
(Process of Operation)
.

c
On-site / Remote Administration End
Return the System Program Switch on the KX-Ti 23211 to the
“SET” position from the “EIA” position Make your data terminal equipment off-line or hang up or enter “BYE” command.
when you enter the “BYE” command;
; ** Jan. 1. 1988 12:OO’AM **
; KX-Ti 23211 remote administration end
; ** Jan. 1. 1988 12:OO’AM **
; KX-T123211 on-site administration end
0 If carrier tone from the data terminal equipment stop while data
communication, the operation with Remote administration will
finish.
3-6

(Process of Operation)
0:
Indication on display of
data terminal equipment
Remote administration
end command
On-site administration
Return ‘the
System Program
Switch to the
Remote administration
I L
; KX-Tl23211 on-site administration end ; KX-T123211 remote administration end
\
Data
terminal
equipment
off-line,
hang up or
Carrier
tone stop
(On-site / Remote Administration End)
-9

.,
,‘.
.:
c
To Edit the data by “Interactive Style” (cont.)
n If you want to change just one parameter of many parameters, you may press I‘ I#I ” key and the parameter number and then press
“ 1/1 m 111 JcR(1)I ” key..
; E > Main command 11Subcommand
ICII
# Parameter number
Example ;
In case of changing the 15th
; E > Main command
or
; E > Main command
In case of changing the 1st
; E > Main command
or
; E > Main command
Subcommand 1 llll1llll
Subcommand JpJ15l~l/
Subcommand I piiEzq IIcR(1)I
Subcommand I#I 011 )j / IcRcr,l
n In case you want to show the setting contents with Edit Mode without changing to show Mode, enter “/ /” after command
as follows.
MS // 1 (To see all parameter with Subcommand S of Main Command)
To see the Starting Time of Day/Night Service Mode on Monday, press 13Sl/ / 1 .
M *:/ / 1 (To see all parameter with Subcommand of Main Command at a time)
To see the Starting Time of Day/Night Service Mode on Sunday through Saturday, press 13s t / / 1 .
M // 1 (To see all parameter with Main Command)
To see the Parity, Carriage Return for a New Line, Word Length, Stop Bit Length and Baud Rate, press 90% / 1 .
.3-B

To Show the Data by “Interactive Style”
1. Press the q q q and 1 Carriage Return ( 1 ) 1 key.
Rl If you wish to know the effective commands which can be
used on this mode, enter the “HLP” command.
; > hlp
; Select the style
Interactive . . . . . . . . . . . . . INT (cr)
,
Batch . . . . . . . . . . . . . . . . . .
FIL (cr)
,
Mode end . . . . . . . . . . . . . .
END (cr)
b--v
; > !.,.!
2. Press the fl w q andICarriage Return ( 1 ) 1key,
; > int
; Interactive style start
I--,
; s> 1-1
q If you wish to know the effective commands which can be
used on this mode, enter the “HLP” command.
; S> hlp
; Please input show command (current style : interactive)
L
r-7
:,=\I I
‘-.I
3. Enter the commands corresponding to the feature that you want to
know. (See page 3-12)
4. To see another data, repeat step 3.
5. Press the m w IDI and lCarriage Return ( 1 ) 1key.
6. Press the q q q and 1 Carriage Return ( 1 ) 1 key.
; > end
; Show mode end
l--q
; > L-1
3 -- I I
.,

L
To Show the Data by “Interactive Style” (cont.)
Enter the command corresponding to the feature that you want to show according to this format.
; S > Main command Ipi%izal~ICR(I)I
The feature names or the data of Main cammand and Subcommand that you want to show are explained on page 5-l through 10-1, so enter
them according to this table, please.
0 “CR ( 1 )” means Carriage Return ( 1 ).
3- 12

To Edit or Show the Data by “Batch Style”
l.Pressthem(H(m 1
Carriage Return ( 1 ) key to select the
Show mode, or
q q q 1 Carriage Return ( 1 )I key to select
the Edit mode.
When Edit mode:
; >edt
; Edit mode start
; > f;j
When Show mode:
; > shw
; Show mode start
I
n If you wish to know the effective commands which can be
used on this mode, enter the “HLP” command.
; > hlp
; Select the style
Interactive . . . . . . . . . . . . . .
,
INT (cr)
Batch . . . . . . . . . . . . . . . . . . FIL (CT)
Mode end . . . . . . . . . . . . . END (cr)
I--,
; > !-!
2. Press the m rl q and 1Carriage Return ( 1 ) 1key.
; > fil
; Batch style start
I
<Transmit the batch data>
I--.
I
L
3. Transmit the batch data to the KX-T123211.
The system data will be shown on the display.
4. When transmission of system data has been finished, the display
will show the following.
n If “EOD” data is programmed in batch data;
; Batch style end
; > [:I
If enter “CNT” command;
When Edit mode:
; E> cnt
1Transmit the next batch data
r--l
I I
I.-.!
When Show mode:
r f “nsmit the next batch data
0 To show or edit another data, repeat step 3.
.

To Edit or Show the Data by “Batch Style” (cont.)
n If “EOD” data is not programmed in batch data, the display will
show the following after two minutes.
When Edit mode:
5. Press q q q 1 Carriage Return ( 1 ) 1 key.
; None “EOD” In batch data
r-3
; E> ‘.-;
When Show mode:
; None “EOD” In batch data
l---l
; s> 1-J
When Edit mode:
When Show mode:
0 To end the batch style, press
q R q 1 Carriage Return ( 1 ) 1
key.
0 To continue the batch style, press the
q q q 1 Carriage Return ( 1 ) 1 key and repeat step 3.
0 If you wish to know the effective commands which can be used on
this mode, enter the “HLP” command within two minutes.
; Select the command (current style : batch)
f
Batch mode end . . . . . . . . . . . . . . . . . * END (cr)
Next batch data . . . . . . . . . . * . . . . . . .
I
CNT (cr)
I--*
; s>!.-l
1; Show mode end
3 - 14

1. Set a floppy disk to the drive of a data terminal equipment.
2. UTo chanqe or proqram a data
0 Enter the command (Main command, Subcommand) and
parameter corresponding to the feature that you want to
change as the way on page 3-9 “Editing or Programming”.
0 When change the other feature, repeat step 0.
O After entering all the data, enter “EOD”.
UTo confirm a data
0 Enter the command (Main command, Subcommand)
corresponding to the feature that you want to confirm as the
way on page 3-12 “Showing”.
0 When confirm the other feature, repeat step 0.
a After entering all the data, enter “EOD”.
3. Make the floppy memorize the entered data.
Example :
q Change or program _
Make the data to edit as follows and memorize the data to the
floppy disk.
0 To change the Extension number which is assigned to jack
number 01 into 190.
e Jack number 02
- Extension number 185
0 Jack number 04 - Extension number 180
0 Jack number 17
- Extension number 165
e To set date into Aug. 31’ 88 (Wednesday)
Enter them to the data terminal equipment as below
OlS/90/85/180/ 1
02s / 65 I 1
04Sl8808313l 1
EOD 1
Note
0 EOD is surely made in the end of batch data.
e One line up to 78 digits.
0 Be sure to press the “Carriage Return ( 1 )” key in conclusion of
one data.
0 “ 1 ” means Carriage-Return.
3- 13

c
To Edit or Show the Data by “Batch Style” (cont.)
(To recognize the made data)
If q is entered in the first line, the line will not be executed when a
batch data is sent to the KX-Ti 23211 from a data terminal
equipment.
If the title of the change contents are entered in the line as following,
it will be useful when use it later because of the recognition of the
contents.
02s I 65 I 1
r-------------------------,
‘1 . DATA=‘88. 8. 37. (WED) SET 1 1
rl------------------------r
04s I 8808373 I 1
EOD 1
To show the data of SYSTEM FEATURE-l through 6
(see page 5-1 through 5-9)
Make the data code as follows and memorize the data code to the floppy disk.
ys 1
02s 1
03s * 1
04s 1
05s 1
06s * 1
EOD 1
n Confirmation
3 - 76

Edit / Show Mode Map
I-
;>
INT
s
; Select the style
; Interactive . . . . . INT (cr)
; Batch . . . . . . . FIL (cr)
; Mode end . . . . . END (cr)
j j Ftyctive style start b
r I
/ j lgactive style start p
(Interactive process)
‘7)) j B~~~~$fi~~~ batch data> I- (Batch process)
3- I/
.0

c
To Dump the Data
1 .Press the m m IpI 1 Carriage Return ( 1 ) 1key.
I
; > dmp
I
; Dump mode start
I
I
l---l
; p> L-1
n If you wish to know the effective commands which can be used on
this mode, enter the “HLP” command.
; P> hlp
; Select the item
..............................
I
AlI ALL (cr)
..........................
F
System SYS (cr)
I
CO. trunk ........................ COT (cr)
,
Ext .............................. EXT (cr)
I
DSS console ..................... DSS (cr)
.......................
.
Doorphone DOR (CT)
........................
I
Mode end END (cr)
; P> [;I
L
2.
Before input of the following commands, set floppy disk to the
data terminal equipment so that the data terminal equipment
can start recording.
Press the command of the parameter that you want to dump.
n The first message will be displayed as follows when each
command is entered.
ALL ; All data dump start
SYS
; System data dump start
1
COT -1 ; CO data dump start 1
EXT ; Ext data dump start
DSS -1 ; DSS console data dump start
I
n The following message will be displayed when Dump is finished.
I
DOR
I
Doorphone Parameter
I
DOR
; Doorphone data dump start
ALL -1 ; All data dump end
SYS ; System data dump end
I
COT
EXT
; CO data dump end
; Ext data dump end
DSS - ;DSS console data dump end
DOR
- ;Doorphone data dump end
3 - 18