Panasonic 308 User manual

Section 300
Issue 1
August 1990
S-DBS
308/616 (V1.0)
Installation
Small Digital Business System
Instructions
308/616
Panasonic

Section 300
Issue 1 August 1990
a+
S-DBS Installation Instructions
Vl .o
FCC RULES AND REGULATIONS (Part 68)
In compliance with the requirements of Part 68 of the FCC Rules and Regulations for
connection ofterminal equipment to the telephone network, and for your convenience,
the following information is presented.
Notifying the Telephone Company
When connecting or disconnecting the terminal equipment to the telephone network
inform the telephone company of the particular line (s) for connection,“the FCC
registration number and ringer equivalence number of the registered terminal
equipment.
FCC RegMration Numb&s
Model Numbers Key System Hybrid System
VB-42010 (DBS308) ACKUSA-61853~KF-E ACKUSA-61855-m-E
VB-42020 (DBSSlS) ACKUSA-61854KF-E ACKUSA-61856-Ml?-E
When enabling Pooled Trunk Access, inform the telephone company or a Panasonic
service center of the MF-E FCC Registration number. According to FCC rules, Pooled
Trunk Access is regarded as one of the distinguishing features of a Pl3X as opposed
to a key telephone system.
RINGER EQUIVALENCE NUMBER @ZEN) 0.5j B
The REN determines the number of devices you may connect to your telephone line
and still have all those devices ring when your telephone number is called. In most,
but not all areas, the sum of the REIVs of all devices connected to one line should not
exceed five (5.0). You should contact your local telephone company to determine the
maximum REN for your calling area.
Service order code 9.OF
Network address signaling code E
Facility interface code 02LS2 (2 wire/Loop start)
Required network interface code RJ25C
Connection to a Party Line or Coin Operated Telephone Line *
Direct Connection to a Party Line or Coin Operated Telephone Line Is Prohibited.
If you are on a party line, check with your local telephone company for further
information.

S-QBS-~~laions------- __- -_-..--..-----.-
..-.-_. _~~.S&ion 300
Vl .o Issue 1 August 1990 ,.- .\
Incidence of Harm to the Telephone Lines
Should terminal equipment cause harm to the telephone network. the telephone company shall. where
practical. notify the customer that temporary discontinuance of Senrice may be required. However,
where prior notice is not practical. the telephone company may temporarily discontinue service
forthwith. if such action is reasonable in the dircumstances. In case of m-r-notified temporary
discontinuance of service. the telephone company shall:
(AI Promptly notify the customer of such temporary discontinuance of setice.
(B) Afford the customer the opportunity to correct the situation which gave rke to the temporary
discontinuance. Q
(C) Inform the customer of the right to bring a complaint to the Co mmission pGsuant to the
procedures set out in Part 68 of the FCC Rules and Regulations.
Compatibility of the Telephone Network and Terminal Equipment
(Al Ax&lability of telephone information o
Technical information on interface parameters and specifkatfons not set by FCC Rules, including
the number of ringers which may be connected to a particular telephone line to permit terminal
equipment to operate in a manner compatible with telephone company communications
facilities, shah be provided by the telephone company upon customer’s request.
BJ Changes in telephone company communications facilities, equipment, operations and
procedures. f-“‘)
.
The telephone company may make changes m its communications facilities, equipment.
operations or procedures, where such action is reasonably required in the operation of its
business and is not inconsistent with the rules and regulations in FCC Part 66. If such changes
can be reasonably expected to render any customer% terminal equipment incompatible with
telephone company communications facilities or require modification or alteration of such
terminal equipment or otherwise materially affect its use or performance, the customer shall be
given adequate notice in writing to allow the customer an opportunity to maintain un-interrupted
Se.
Hearing Aid Compatibility
This system is hearing-aid compatible.
_._.-Automatic Dialers
WhenProgrammtn g Emergency Numbers or Making Test Calls to Emergency Numbers:
W Remain on the line and briefly explain to the dispatcher the reason for the call.
(B) Perform such activities in the off-peak hours, such as early morning or late evenfng.
iv

Section 300
----.-Issue l--August--l 990..
a
S-DBS Installation Instructions
VI .o
ResponsibiIity of Grantee (Manufacturer) of Registered Equipment
The Grantee or its agent shall provide the user of the registered equipment with the following:
0 Instructions concerning installation, operation and repair procedures, where applicable.
(B) Notification that the registered terminal equipment may not be used with party lines or coin ltnes.
(C) Instruction indicating that when trouble is experienced the customer shall disconnect the
registered equipment from the telephone hne to determine whether it Is malfunctioning. If so, the
use of such equipment shall be discontinued until the problem has been corrected.
(D) If comxctions other than FLJ25C are needed. contact the local telephone company.”
Product Safety
Please Observe the Following Guidelines to Assure the Safe Usi: of Your Telephone
0 This product is an electrical device and can be hazardous if immersed in water.
WJ li ~~otusethfsu~~~~~-~~tub, shower. or when
wet. Ifyou accidently drop the unit into water, unplug it first, then retrieve it by pulling the cord:
(C) The telephone should not be exposed to heat sources, direct sunlight, extreme temperatures.
moisture. strong vibrations, greasy or dusty environments.
(D) Never attempt to insert wires, pins or similar objects in the vents or openings of the telephone.
(E) Never clean the telephone with benzol, paint thinner or other solvent materials.
(F) Never install telephone wiring during a lightning storm.
(G) Never Install telephone jacks in a wet area unless they are specifically designed for that purpose.
03) Never touch un-insulated telephone wires or terminals unless the telephone line has been
d&connected at the network interface.
Radio Interference (Part 15)
Warning -This unit generates, uses and can radiate radio frequency energy. If not installed and used
in accordance with the instructions manual, the unit may cause radio interference. The Unit has been
tested and found to comply with the hmits for a Class A digital device pursuant to Part 15 ofFCC Rules,
which are designed to provide reasonable protection against such interference when operated in a
commercial environment.
Op&ation of this equipment in a residential area is likely to cause harmful interference m which case
the user at his own expense will be required to take whatever measures necessary to correct the
interference.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions.
The usermay find the following booklet prepared by the Federal Communications Commission helpjul:
Somethine about Interference
This booklet Is available from the FCC local regional offices.
V

Section 300
Issue 1July 1990 S-DBS Installation Instructions
v1.0
_--.. ..-.
Table of Contents
FCC RULES AND REGULATIONS (Part 68) ...
............................................ Ill
Notifying the Telephone Company ...
.................................................... 111
RINGER EQUIVALENCE NUMBER (REN) 0.5 B ...
.................................... lJ.l
Connection to a Party Line or Coin Operated Telephone Line.. ............ -9.. iii
Incidence of Harm to the Telephone Lines .............................................. iv
Compatibility of the Telephone Network and Terminal Equipment .......... iv
Hearing Aid Compatibility ......................... .............................................. iv
Automatic Dialers .................................................................................. iv
Responsibility of Grantee (Manufturer) of Registered Equipment ........ v
Product Safety ......................................................................................
V
Radio Interference (Part 15) ..................................................................
V
INTRODUCTION ........................................................................ 1
POOLED TRUNK ACCESS ..........................................................
2
ENVIRONMENT ........................................................................
4
Electrical Noise ......................................................................................
Gas and Airborne Particles ....................................................................
Humidity ..............................................................................................
uw% ................................................................................................
wwnm ..............................................................................................
Temperature ..........................................................................................
Vibration ..............................................................................................
Water Factor ..........................................................................................
4
4
4
4
4
4
5
5

S-DBS Installation Instructions
v1.0
.__._._ma~mmoN ...........................................................................
6
Main Unit .............................................................................................. 6
Removing the Main Cabinet Cover ..................................................................
6
Wall-Mounting Procedure for the Main Cabinet Cover .................................... 7
Installing the Backup Batt&y ..........................................................................
8
I.nitial.jzing the System ......................................................................................
9
Key TeIephone ........................................................................................ “lo
Wall-Mounting Procedure, ................................................................................
10
Trunk Unes ........................................................................................... 11
Connectingthe Trunk Lines............................................................................ 11
Internal Lines 8
........................................................................................ 13
Connecting the Telephone ................................................................................
13
SMDR Interface Card ............................................................................... 19 ___...-...
__--_- __
Feature Package ‘B” ........................................................................................
19
Installing the SMDR Card ................................................................................
20
Doorphone Interface Card ...................................................................... 22
Installing the Doorphone Interface ..................................................................
22
Door Box ................................................................................................ 24
Connecting the Door Box ................................................................................
24
Power Failure Unit .................................................................................. 25
Wall-Mounting Procedure ................................................................................
‘25
Connecting the Power Failure Unit ..................................................................
26
Music-On-Hold (MOH) ............................................................................ 28
External Paging ...................................................................................... 29

Section 300
Issue 1JuIy 1990
FIGURES
Q.
S-DBS Installation Instructions
v1.0
1. Main Unit - RAM Switch ......................................................................
2
2. System Connection Layout ..................................................................
3
3. Removing the Main Cabinet Cover ........................................................
6
4. Wail-Mounting Procedure for the Main Cabinet Cover ..........................
7
5. InstaIling the Backup Battery cr
.............................................................. 8
6. Initializing the System .......................................................................... 9
7. Wall-Mounting Procedure for the Key Telephone .................................. 10
a
8. Connecting the Trunk Lines ................................................................ 12
9. Connecting the Telephone .................................................................... 13
8
10.66 Split Block ....................................................................................... 18
11. SMDR Interface Card - Feature Package “B” ........................................ 19
12. Installing the SMDR CARD. ..................................................................
22
---.-13. ‘Doorphone. Interface Card ....................................................................
23
14. Connecting the Door Box ......................................................................
24
15. Connecting the Power Failure Unit ......................................................
27
16. Connecting Music Source to the MOH Connector ..................................
28
17. Connecting the Paging Speaker to the Amplifier .................................... 29
TABLES
1. System Configuration .......................................................................... 1
2. Extension Connector S-DBS 308/616 .................................................. 14.15
. Extension Connector S-DBS 616 .......................................................... 16.17
3 Prim&r-Gerkne&ie*. ............................ i...T..-.-.-i-~-i-.-P~~-~~~~..-.-.-.........................
20
4. Wire Gauges ........................................................................................
22,24
5. MOH Input Impedance ........................................................................ 28
6. EPA Output Impedance ......................................................................... 29

Section 300
Issue I August 1990
INTRODUCTION
%s
S-DBS Installation Instructions
VI.0
The S-DBS is available in two basic system configurations, each has a different
number of outside and internal lines.
TABLE 1. System C~dguratio~
System Designation Trunk Ports Extension Port%
VB-42010/DBS 308 -., 3 8
VB-42020/DBS 616 6 a 16
9
The S-DBS consists of the main unit, telephones and various peripheral equip-
ment and requires installation, wiring and programming:This manual describes
the installation and wiring procedures.
!;
1
i
i
!\
i
‘.vs
“r.

.,,,
*
& :
S-BBS Installation Instructions Section 300
v1.0 Issue 1August 1990 r
POOLED TRUNK ACCESS
FROGIWIMMING FOR AN AUTOMATIC OUTSIDE LINE GROUP
This function cannot be programmed until one umper cable on the KSU has been
cut. After cutting the cable and progr amming 2or Pooled Trunk Access, calls are
automatically connected to an outside line.
FCC Registration Numbers c
Model Numbers
_
Key System Hybrid System
1
m-42010 (DBS308) ACKUSA-61853~IXF-E ACKUSA-61855~&IF-E
VB-42020 (DBS616) ACKUSA-61854~KF-E ACKUSA-61856~&IF-E
When enabling Pooled Trunk Access. in&m the telephone company or a Panasonic
service center of the MF-E FCC Registration number. According to FCC rules, Pooled
Trunk Access is regarded as one of the distinguishing features of a PBX as opposed
to a key telephone system. s,
!*
2
MAIN UNIT
RAM SWITCH
HOLD CLR MW
Figure 1

Section 300 lrgdi
S-DBS Installation Instructi6ns
v1.0
Issue 1August 1990
SYSTEM CONNECTION LAYOUT
1
Printer
‘.. RS-232C Interface
for TTY or SMDR
Door Opener 2
Door Phone
Door Opener 1
COL 4
COL 5
COL 6 I--
CO Line
Port ZxtemalPaging
ez@!7
@.J’
!
tension Port 1
1
.l.-
Extension Port 8
Door Phone 1
Door Phone 2
.PFu Power
I
Adaptor
COL 1
COL 2 I-
for Music-on-Hold
Backup Battery
i
J
SLT
3

S-DBS Installation Instructions
v1.0 Section 300
Issue 1 August 1990
ENVIRONMENT
Electrical Noise --
_-. .--~-..--- -~--..-.---.
ElectJical noise might disturb the operation of the system’s digital control circuits.
Placethe equipment away from heavy motors, welders or dimmers, and radio receivers
and computers which generate electrical noise.
Conversely, this system may interfere with radio receivers and computers. P&e the
main unit at least 10 feet (3 meters) away fi-om ail other equipment.
Gas and Airborne Particles
To avoid corrosion or oxidation of electri al relay contacts, place the equipment in an
6
area free of airborne particles and corro ive gas.
Excessive humidity may oxidize the metallic parts and cause errors in performance.
Do not install equipment in high humidity areas.
___
-- .__--
Hxdity: 30% to 90% relative humidity
Non-Condensing
Appropriate lighting is required when servicing the main unit.
Protect the system from lightning by properly grounding the AC cable as well as
instalhngvoltage surge suppressors and diode clamps on all external cables attached
to the system.
TemperatureTemperature
Integrated circuits (ICs) and Large Scale Integrated circuits (LSXcs)require adequateIntegrated circuits (ICs) and Large Scale Integrated circuits (LSXcs)require adequate
ventilation for the main unit to allow upward circulation of air through the cabinetventilation for the main unit to allow upward circulation of air through the cabinet
. grille.. grille. II
Operating room temperature: 0°C to 40°C (32°F to 104°F)
Storage Temperature: -10°C to 50°C (14°F to 122°F)
4

Section 300
Issue 1 August 1990
ENVIRONMENT (continued)
Vibration
Do not install the system in an area with
disconnection or loosening of components.
Water Factor
%s
S-DBS Installation Instructions
v1.0
excessive vibration which can cause
Water is adangerous hazard to equipment and can totally damage the system. Do not
place the equipment near anything containing water or under overhead plumbing,
sprinkler system values or in areas that are susceptible-to flooding.
B !e

S-DBS Installation Instructions
v1.0 Section 300
Issue 1August 1990
INSTALLATION
Always set the power switch to 6E’PTEEe instaE%~~EtionnectiEithe AC power to
the key system unit (KSU).
Use the appropriate screwdriver to fasten the screws. 22
Handle the Main Unit carefully to avoid damaging the cover.
.a
1. Removing the Main Unit Cover
a) Remove the two screws
main unit.
0
a from &e front cover (B) of the
b) Remove the tiont cover (B) by pulling it to the left@.
Frant aover B
0
b
0
a SCrBw,
--.- -..-__
6

Section 300
Issue 1 August 1990
*
S-DBS Installation Instructions
v1.0
INSTALLATION (continued)
2. Wall-Mounting. Procedure for the Main Cabinet Cover
a) Attach four screws loosely to a wall stron fl enough
to hold the wei ht of a KSU. The screws s ould
___ _~_. - ---stand--out one-fourth of an inch from-the wall surface.
b) Pass the screws through the holes on the back of (r
the main cabinet and pull the cabinet in a
downward direction. -
c) Tighten the two screws (A) and (B) with a screwdriver
to secure the cabinet to the wall.
(8)

*.
Section 300
Issue 1August 1990 f‘? I
S-DBS Installation Instructions
v1.0
INSTALLATl[ON (continued)
3. Installing the Backup Battery
a) Place the backup batteries (W-42130) in the
battery compartment of the KSU.
b) Insert the connecter cord of the batteries onto
the BAT terminals of the KSU (+ and -). (?
In case of power failure the backup battery will support normal system operation for,
approximately, 30 minutes under full-load for the DBS3Q8 system and, approxi-
mately, 20 minutes for the DBS616 system.
The batteries are trickle charged during+normal system operation.
BATTERY Figure 5
MAIN
UNIT
CONNECTOR
_____.._..___. _- .._...-... .--_-- .--. .-.
n
0

Section 300
Issue 1 August 1990
ei+
S-DBS Installation Instructions
v1.0
INSTALLATION (continued)
4. Initializing the System
a) Set the power switch of the main unit to OFF.
b) Set the RAM switch in the center of the KSU
Tom the HOLD to the CLEAR position.
CJ plum the power surltcIi’?PtIie~iinitX~~ON~
d) Set the RAM switch back to-HOLD.
Q
Ram Switch
Hold Clr MC0
L

S-DBS Installation Instructions
v1.0
KEY TELEPHONE
1. Wall-Mounting Procedure
4
bl
cl
d)
Place the telephone face down on a soft surface.
Push in on the wide end of the dark grey wall
adapter with thumbs or heels of hands until the
adapter is released.
Turn the adapter upside down. Insert the guides
into the two adapter mounting holes at the
lower end of the key telephone,-then push in
the--adapter. --- .._ _---.--.. a
Place the mounting holes of the bracket over the
studs of the modular jack and pull the telephone
downward to secure it in place. Short station
cords are provided for wall mounting.
Remove the handset guide by pulling it up and out
with fingernail or screwdriver. Turn the guide
upside down and reinsert it into the handset.
Section 300
Issue 1August 1990
Wall mounting adaptor
rr-l------m
10

Section 300
Issue 1 August 1990
Fci+
S-DBS Installation Instructions
v1.0
TRUNKLINES
1. Connecting the Trunk Lines
The telephone cable from the CO/PBX line can be directly connected to the outside
line jack on the main unit.
The DBS308 system has a six-pin modular jack (RI-25C) for COL 1, COL qand COL
3. The DBS616 system has two modular jacks for COL 1, COL 2 and COL 3, and COL
4, COL 5 and COL 6.
y;z.ft the outside lines to the COL jack with a 6-w-ire modular cord no longer than
I/

___.---__
S-DBS Installation Instructions
VI.0
TRUNK LINES (continued)
Figure 8
Section 300
Issue 1 August 1990
P*
/ ‘. .
co 1-3
CNl
CN2
CO 4-6
rc >
COL 1
COL5
111111
< > < H
COL3
COL6
MAIN
UNlT
.-
c
.
I
12

Section 300
Issue 1August 1990
%+
S-DBS Installation Instructions
v1.0
Use a female 25-pair cable to connect the extension ports to a 50-pin split block.
The DBS308 system has one connector on the main unit for extensions 1to 8, DPHl,
DPH2 and PFU output. The DBS616 has two connectors for extensions 1 to 8 and
extensions 9 to 16.
Except for ports 1 and 2 which are for key telephones only, each extension port can
connect a key telephone and/or a single line telephone (SLT).
1. Connecting the Telephone -
a) For each telephone connect two wires to the
--- -- -- appropriate-pins of-the split @lock.--(See-TABLE2 i&
and Figure 10 for Extension Connectors)
b) Plu the 50-pin connector of the split block
to & e extension port on the main unit.
NOTE: The 25-pair amphenol connector which
leads to the split block is held in place by a
plastic tie. The tie can be attached to two
hooks on either side of the connector. (See
Figure 9 below)
J
S-Pair AmphenoI
hncctor