Panasonic KX-TG5100M User manual

5.8GHz Expandable Cordless Phone System
Model No. KX-TG5100M
KX-TG5110M
Pulse-or-tone-dialing capability
Operating Instructions
Charge the battery for about 6 hours before initial use.
PLEASE READ BEFORE USE AND SAVE.
Contents:
Location of Controls 2
Connections 5
Battery Installation/Battery Charge 6
Recording a Greeting Message 7
Making/Answering calls with the Handset 8
Making/Answering calls with the Base Unit 9
Caller ID Service 9
Automatic Answering Operation 10
Listening to Messages 10
Important Safety Instructions 11
FCC and Other Information 13

–2–
Please read IMPORTANT SAFETY
INSTRUCTIONS on page 11 before use.
Read and understand all instructions.
Location of Controls
■Handset
Headset Jack
[TONE] Button
[](TALK) Button
[](Speakerphone)
Button
[CONF (Conference)/
FUNCTION
] Button
Microphone
Charge Contacts
Antenna
Display
[OFF] Button
[HOLD/INTERCOM/CLEAR]
[PAUSE/REDIAL] Button
Soft Keys
Receiver
[FLASH/CALL WAIT] Button
Navigator Key
( , , , )
Back side
Speaker

–3–
■Base unit
Display
[MUTE] Button and Indicator
[CALL WAIT/FLASH] Button
[REDIAL/PAUSE] Button
[PRIVACY] Button
[STOP] Button
[GREETING]
Button
[MEMO]
Button)
Antenna
Antenna
[MIC] (Microphone)
[DIGITAL SP-PHONE] (Speakerphone)
Button and Indicator
[LOCATOR/INTERCOM/
TRANSFER] Button
and Indicator
[HOLD] Button
[CONF] (Conference) Button
[ERASE] Button
[ANSWER ON]
Button and
Indicator
CHARGE Indicator
Charge Contacts
Navigator Key ( , , , )
[
Y
] ( TONE ) Button
MAILBOX
Buttons)
[FUNCTION/EDIT]
Button

–4–
■Charger unit
CHARGE
Charge Contacts AC Adaptor
CHARGE Indicator

–5–
Connections
■Connect the AC adaptor and the telephone line cord.
•USE ONLY WITH Panasonic AC ADAPTOR PQLV10. (Order No. PQLV10Z )
•The AC adaptor must remain connected at all times. (It is normal for the
adaptor to feel warm during use.)
Hook
Telephone Line Cord
Single-Line Telephone Jack (RJ11C)
Fasten the AC adaptor cord to
prevent it from being
disconnected.
AC Adaptor
Power Outlet (AC 120 V, 60 Hz)
Raise the antennas.
Power Outlet
(AC 120 V, 60 Hz)
AC Adaptor
• USE ONLY WITH Panasonic AC ADAPTOR
PQLV2 (Order No. PQLV2Z ).
•The AC adaptor must remain connected at all times. (It is normal for the
adaptor to feel warm during use.)
■Charger unit

–6–
Battery Installation/Battery Charge
■Recharge
Recharge the battery when:
–"Recharge battery" is displayed,
–" " flashes on the display, or
–the handset beeps every minute while it is in use.
•Clean the handset and the base unit charge contacts with a soft, dry
cloth once a month. Clean more often if the unit is subject to grease,
dust or high humidity. If not, the battery may not charge properly.
•If the battery is fully charged, you do not have to place the handset on the
base unit until "Recharge battery" is displayed and/or " " flashes.
This will maximize the battery life.
•The battery cannot be overcharged.
■Battery installation
1 Install the battery in the handset.
2 Close the handset cover.
■Battery charge
To power the handset, charge the battery.
Place the handset on the base unit for about 6 hours before initial use.
A nickel cadmium battery that is recyclable powers the product
you have purchased. At the end of its useful life, under various
state and local laws, it is illegal to dispose of this battery into
your municipal waste stream. Please call
1-800-8-BATTERY for information on how to recycle this
battery.

–7–
You can record a personal greeting message of up to 2 minutes. If a greeting
message is not recorded, one of two pre-recorded greetings will be played
when a call is received.
•All messages (greeting, incoming, etc.) are stored in digital memory. The
total recording time is about 15 minutes. We recommend you record a
brief greeting message in order to leave more time for recording new
messages.
1 Press and hold (GREETING) until a long beep is heard.
2 After the long beep, talk clearly, about 20 cm (8 inches) away from the MIC
(microphone).
3 When finished, press (GREETING).
•If you do not record a greeting message, one of two messages will be played
when a call is received, depending on the caller’s recording time.
Recording a Greeting Message

–8–
■To make a call
1 Press or .
2 Dial a telephone number.
3 To hang up, press (OFF) or place the handset on the base unit.
•If "No link to base. Walk closer to base and try again" is
displayed and an alarm tone sounds in step 1, move closer to the base unit
or place the handset on the base unit, and try again.
•To redial the last number, press or , then press
(PAUSE/REDIAL).
•To adjust the receiver volume/speaker volume:
To increase, press . To decrease, press .
•To put a call on hold, press (HOLD/INTERCOM/CLEAR).
•To release the hold, press (HOLD/INTERCOM/CLEAR).
■To answer a call
Press or .
Making/Answering Calls with the Handset

–9–
Making/Answering Calls with the Base Unit
■To make a call
1 Press (DIGITAL!SP-PHONE).
2 Dial a telephone number.
3 Talk into the MIC (microphone).
4 To hang up, press (DIGITAL!SP-PHONE).
•To redial the last number, press (DIGITAL!SP-PHONE), then press
(REDIAL/PAUSE).
•To adjust the speaker volume:
To increase, press . To decrease, press .
•To put a call on hold, press (HOLD).
•To release the hold, press (DIGITAL!SP-PHONE).
■To answer a call
Press (DIGITAL!SP-PHONE), then talk into the MIC (microphone).
Caller ID Service
This unit is compatible with a Caller ID service offered by your telephone
company.
After subscribing to a Caller ID service, the calling party’s information will be
shown on the handset display after the first ring.
The unit can record information of up to 30 different callers in the caller list.
The Caller List information is sorted from the most recent to the oldest call.
When the unit receives the 31st call, the oldest call is deleted.
If your unit is connected to a PBX system which does not support Caller ID
services, you cannot access those services. Please consult your equipment
supplier.

–10–
Automatic Answering Operation
■ How to use the mailboxes
The unit accommodates three mailboxes (Mailbox 1, 2 and 3). A caller can
leave a message in a specified mailbox. If a mailbox is not specified,
messages are recorded in the mailbox 1.
■ When a caller calls
The caller can select a mailbox by pressing (#) and (1) (Mailbox 1), pressing
(#) and (2) (Mailbox 2) or pressing (#) and (3) (Mailbox 3), while the greeting is
played. The caller can then record a message in the mailbox after a beep.
OR
The caller waits until the greeting finishes, and records a message after a
beep. The message will be recorded in the Mailbox 1.
■ Setting the unit to answer calls
Press (ANSWER!ON) to turn on the answering system.
•The indicator lights and “Answer set”is heard.
Listening to Messages
You can see the total number of recorded messages on the base unit display.
If the ANSWER ON indicator flashes and the mailbox icon(s) ( ,
and ) flash(es) on the display, new messages have been recorded in
the mailbox(es).
To listen to the messages, press (MAILBOX!1), (MAILBOX!2) or (MAILBOX!3).
•When you have new messages, the unit announces the number of new
messages and plays them back.
•When you have no new messages, the unit plays back all recorded
messages.
BOX 3
BOX 2BOX 1