Panduit smartzone G5 User manual

G5 PDU User Manual

SMARTZONE G5 USER MANUAL
1
Contents
Figures............................................................................................................................4
Section 1 – System Overview .........................................................................................6
Intelligent Network Controller.......................................................................................6
Connecting the PDU to a LAN Ethernet Port...............................................................6
Connecting the PDU to a Computer Serial Port...........................................................7
Setup Serial Communication....................................................................................8
Section 2 – Web Graphical User Interface (GUI) Configuration....................................11
Internet Protocol (IP) Address ...................................................................................11
Web Configuration.....................................................................................................11
Supported Web Browsers......................................................................................11
Logging in to the Web Interface.............................................................................11
Introduction to the Web GUI......................................................................................12
Menu Dropdowns...................................................................................................15
Introduction to the Dashboard ...................................................................................16
Section 3 – Simple Network Management Protocol (SNMP).........................................18
SNMP Management Configuration............................................................................18
Configuring Users for SNMP v3 Communications.....................................................22
Section 4 – Command Line Interface (CLI) Configuration.............................................25
Connecting through CLI connection...........................................................................25
Supported Commands...........................................................................................25
Connecting to the CLI through the serial interface.....................................................26
Section 5 – Local Display..............................................................................................29
OLED Display............................................................................................................29
Menu Mode............................................................................................................30
OLED Menu Structure ...............................................................................................31
Main Menu Selections............................................................................................31

SMARTZONE G5 USER MANUAL
2
Setup Menu............................................................................................................32
Sensors Menu ...........................................................................................................43
Section 6 – User Access...............................................................................................45
Access Types.........................................................................................................47
Setting up the system for Radius Authentication.......................................................49
Configuring the system with LDAP Server Settings...................................................50
Section 7 – Daisy Chain Configuration..........................................................................54
Daisy-Chain Overview...............................................................................................54
Daisy-Chain Setup.....................................................................................................54
RNA (Redundant Network Access) Functionality ......................................................55
RNA Setup.................................................................................................................56
Section 8– Web GUI configuration................................................................................58
G5 iPDU Outlet Power Sequence Setup ...................................................................58
Section 9 – Connecting and Configuring Optional Hardware........................................62
Accessory Hardware Overview..................................................................................62
Configuring Environmental Sensors ..........................................................................65
Warranty and Regulatory Information............................................................................66
Warranty Information.................................................................................................66
Regulatory Information ..............................................................................................66
Support and Other Resources.......................................................................................67
Accessing Panduit Support........................................................................................67
Acronyms and Abbreviations.........................................................................................68
Documentation Feedback .............................................................................................71
Appendix A: CLI Commands.........................................................................................72
Appendix B: Firmware Update Procedure.....................................................................80
USB Method..............................................................................................................80
Web Interface Method ...............................................................................................80
FTPs Method.............................................................................................................82
Bootloader Mode.......................................................................................................83

SMARTZONE G5 USER MANUAL
3
Firmware Recovery with Bootloader Mode................................................................83
Appendix C: System Recovery......................................................................................84
Upgrade Configuration with Bootloader Mode...........................................................84
Appendix D: PDU Alarms..............................................................................................85
Trap Codes assigned to Alarms List..........................................................................87
Appendix E: Horizontal Intelligent Network Controller Replacement.............................92
Appendix F: Vertical Intelligent Network Controller Replacement.................................95

SMARTZONE G5 USER MANUAL
4
Figures
Figure 1: Ethernet Port for Network Connection..............................................................7
Figure 2: Locate Reset Button.........................................................................................8
Figure 3: Port Setup Settings..........................................................................................9
Figure 4: Login Page.....................................................................................................12
Figure 5: Landing Page.................................................................................................13
Figure 6: Power Summary Page...................................................................................16
Figure 7: Outlet Monitoring Page ..................................................................................16
Figure 8: Environmental Page.......................................................................................17
Figure 9: Security Page.................................................................................................17
Figure 10: SNMP Management.....................................................................................18
Figure 11: SNMP General.............................................................................................19
Figure 12: SNMP Port...................................................................................................20
Figure 13: Setup SNMP Port and Trap Port..................................................................20
Figure 14: Define SNMP V1/V2c User..........................................................................21
Figure 15: Edit V1/2c Manager......................................................................................21
Figure 16: SNMP V3 Manager......................................................................................22
Figure 17: SNMP V3 Edit..............................................................................................23
Figure 18: Connect the RJ-45 end of the cable to the Serial+RS485-1 connector........26
Figure 19: Serial Cable Pinout ......................................................................................27
Figure 20: the OLED Display Orientation......................................................................29
Figure 21: OLED Menu Structure..................................................................................31
Figure 22: Main Menu Selections..................................................................................32
Figure 23: Setup Menu..................................................................................................32
Figure 24: Network Submenu........................................................................................33
Figure 25: Device Submenu..........................................................................................34
Figure 26: Screen Submenu .........................................................................................35
Figure 27: Language Submenu.....................................................................................36
Figure 28: USB Submenu .............................................................................................37
Figure 29: Units Submenu.............................................................................................38
Figure 30: Alarms Menu................................................................................................39
Figure 31: Power Menu.................................................................................................39
Figure 32: Device Submenu..........................................................................................40
Figure 33: Phase Submenu...........................................................................................41
Figure 34: Breaker Submenu........................................................................................42
Figure 35: Outlet Submenu...........................................................................................43
Figure 36: Sensors........................................................................................................44

SMARTZONE G5 USER MANUAL
5
Figure 37: Changing Your Password.............................................................................45
Figure 38: After Login....................................................................................................46
Figure 39: Change User Password...............................................................................46
Figure 40: Change Password........................................................................................47
Figure 41: User Settings................................................................................................49
Figure 42: Radius Configuration....................................................................................50
Figure 43: LDAP Configuration .....................................................................................51
Figure 44: Enable Role Privileges.................................................................................52
Figure 45: Test LDAP Configuration..............................................................................53
Figure 46: How to Connect Cables for Daisy Chain......................................................55
Figure 47:Control & Manage PDU.................................................................................58
Figure 48: Outlet Control Enabled.................................................................................59
Figure 49: Edit Outlets...................................................................................................59
Figure 50: One-Delay Time...........................................................................................60
Figure 51: Saved Sequence..........................................................................................61
Figure 52: Sensor Ports for vertical PDU ......................................................................64
Figure 53: Sensor Ports for Horizontal PDU..................................................................64
Figure 54: Update Firmware..........................................................................................81
Figure 55: Upload Firmware..........................................................................................82
Figure 56: Unscrew Intelligent Network Controller........................................................92
Figure 57: Remove Intelligent Network Controller from PDU........................................93
Figure 58: Inserting New Intelligent Network Controller................................................94
Figure 59: Removing Top and Bottom Screw from Intelligent Network Controller.........95
Figure 60: Disconnecting and Reconnecting the Intelligent Network Controller............96

SMARTZONE G5 USER MANUAL
6
Section 1 – System Overview
Intelligent Network Controller
The Panduit Monitored Input, Monitored & Switched, Monitored per Outlet, and
Monitored & Switched per Outlet PDUs have an integral, hot swappable Intelligent
Network Controller. The Intelligent Network Controller contains the OLED interface,
control buttons, the USB, Ethernet, Serial and Sensor ports, and recessed Reset
Button.
Reset Button
Pressing the Reset Button only reboots the Intelligent Network Controller. It does not
change the Energy (kWh) value and does not affect the output voltage.
Using the Reset Button
Press and hold the Reset Button for 8 seconds to recover from an Intelligent Network
Controller communication failure.
Connecting the PDU to a LAN Ethernet Port
The PDU is defaulted to DHCP. If you are connected to an Ethernet with a DHCP
server, the PDU automatically get an IP address and display it on the LCD screen. If
there is no DHCP server, the default IP address is 192.168.0.1, but again this will be
displayed on the PDU.
Connecting the PDU to a LAN provides communication through an Internet or Intranet
connection. You can monitor the PDU from any computer connected to the same
network. The PDU is set to use DHCP (Dynamic Host Configuration Protocol) by default
when delivered. If IP is successfully assigned, you will see the IP address shown on
OLED display.
1. Locate the Ethernet cable.
2. Connect one end of the cable to the Ethernet port on the PDU (see Figure 1).
Connect the other end of the cable to the Ethernet port on the router (or another
LAN device).

SMARTZONE G5 USER MANUAL
7
Figure 1: Ethernet Port for Network Connection
Connecting the PDU to a Computer Serial Port
If unable to connect to network, you can change the network setting using the serial
interface.
To configure the network setting, perform the following steps:
1. Serial connect the PDU to a computer’s serial port. Set baud rate for a terminal
emulation program.
2. Using a CLI command to enable DHCP or set a static IP.
3. Verify access to the Web interface. The Ethernet LED on the PDU front panel
provides communication status by color and display activity. The recessed Reset
button restarts the PDU (see Figure 2 below).

SMARTZONE G5 USER MANUAL
8
Figure 2: Locate Reset Button
Setup Serial Communication
You may configure the network settings using the command line interface (CLI) with a
serial connection. Users can connect serially using the optional RJ45-DB9 cable (or
make your own cable by creating a unique pinout as described below in the “Serial
Cable Pinout to Create Your Own Cable” in Section 4).
1. Verify that the computer has a serial port. If your computer does not have a DB9
serial connector, but does have a USB connector, obtain a USB-to-DB9 Adapter to
convert the USB to a DB9 serial port.
2. Using the optional RJ45-DB9 cable, connect the RJ-45 end to the port labeled
“Serial+RS485-1” on the front panel of your PDU model (see Figure 1). Connect the
DB9 end of the cable to the computer.
3. Open the terminal emulation program (HyperTerminal or PuTTY) on the computer
and select the serial port connection (such as COM1).
4. Set the communications port as follows:
•Bits per second: 115200
•Data bits: 8

SMARTZONE G5 USER MANUAL
9
•Parity: None
•Stop bits: 1
•Flow control: None
(See Port Settings example below)
Figure 3: Port Setup Settings
5. Use the default initial login indicated below. Note that the username and password
are both case sensitive:
•Username: admin
•Password: 12345678 (or your new password)
6. The “Panduit>” prompt appears after you have logged in, ready to enter the CLI
command.
7. To configure network settings, enter the appropriate “net” command and press
Enter. All commands are case sensitive. You can type ?to access the commands.
8. To enable the IPv4 DHCP by default, run:
•net tcpip dhcp

SMARTZONE G5 USER MANUAL
10
•Enter Y to confirm and the PDU’s Intelligent Network Controller will reboot.
9. To set a static IPv4 configuration, run:
•net tcpip static x.x.x.x (ipaddress) x.x.x.x (netmask) x.x.x.x (gateway)
•Example: net tcpip static 192.168.1.100 255.255.255.0 192.168.1.1
•Enter Y to confirm and the PDU’s Intelligent Network Controller will reboot.

SMARTZONE G5 USER MANUAL
11
Section 2 – Web Graphical User Interface (GUI)
Configuration
Internet Protocol (IP) Address
The PDU is by default configured Dynamic Host Configuration Protocol (DHCP). The
PDU automatically obtains an IP address via a DHCP server when connected to a
network. The IP address the PDU received is displayed on the OLED screen. After the
PDU received the address, login to the Web interface to configure the PDU and assign
a static IP address (if desired). If there is no DHCP server, the default IP address is
192.168.0.1, but again this will be displayed on the PDU.
If the network does not use a DHCP server, see the CONNECTING THROUGH A
SERIAL CONNECTION section to configure a static IP address.
1. Connect a standard Ethernet patch cable to the Ethernet port on the PDU.
2. Connect the other end of the Ethernet cable to the LAN.
3. Make sure the Ethernet port on the PDU shows a solid green light on the left and a
flashing yellow light on the right to indicate successful connectivity to the network.
4. Use the menu buttons to look up the IP address of the device on the OLED display
by selecting Setup > Network > IPv4 or IPv6 as applicable.
5. In a standard web browser, enter the PDU IP address and proceed to configure the
PDU as shown in the Web Configuration section.
Web Configuration
Supported Web Browsers
The supported Web browsers are Windows Firefox, Linux Firefox, Mozilla Firefox,
Windows Internet Explorer Version 11, Microsoft Edge, and Google Chrome mobile and
desktop, Apple Safari mobile and desktop.
Logging in to the Web Interface
Logging In
•Open a supported web browser and enter the IP address of the PDU.
oIf username and password were configured during the Network Configuration
Setup: enter the username and password in the appropriate fields. Press
Login or Enter.

SMARTZONE G5 USER MANUAL
12
oIf username and password were NOT configured during the Network
Configuration Setup, use the default username: admin and password:
12345678. For security purposes, change the password upon login.
Introduction to the Web GUI
Login Page
Figure 4: Login Page

SMARTZONE G5 USER MANUAL
13
Landing Page
Figure 5: Landing Page
Number
Icon
Description
1
The home icon provides an
overview of the PDU with
access to the Dashboard,
Identification, and Control
& Manage.
2
The Alarm icon provides
details of the active critical
alarms and active warning
alarms.
3
This icon lets you select a
Language. There are
seven languages available
to choose from: English,
Chinese, French, Italian,
German, Spanish, Korean
and Japanese.
4
This icon provides the logs
of the PDU which can be
viewed and downloaded.

SMARTZONE G5 USER MANUAL
14
Number
Icon
Description
5
The settings icon allows a
user to setup the Network
Settings, System
Management, SNMP
Manager, Email Setup,
Event Notifications, Trap
Receiver, and Thresholds.
6
The search icon allows you
to input key words and
search for the related
results.
7
Information about the PDU
can be found using this
icon. You also can also
click user guide and
license to ask for help.
8
This icon shows who is
logged in (user or admin).
Account passwords can be
changed, and user
accounts managed
through this page.

SMARTZONE G5 USER MANUAL
15
Menu Dropdowns
Overview
Alarms
Help
Language
Logs
Settings
Admin

SMARTZONE G5 USER MANUAL
16
Introduction to the Dashboard
Power Summary Page
Figure 6: Power Summary Page
Outlet Monitoring Page
Figure 7: Outlet Monitoring Page

SMARTZONE G5 USER MANUAL
17
Environmental Page
Figure 8: Environmental Page
Security Page
Figure 9: Security Page

SMARTZONE G5 USER MANUAL
18
Section 3 – Simple Network Management
Protocol (SNMP)
SNMP Management Configuration
Setup SNMP
1. Access the Web interface and login.
2. Under SNMP Managers, select SNMP General. The SNMP General page
displays.
Figure 10: SNMP Management
3. The SNMP General includes SNMP Access and Version.

SMARTZONE G5 USER MANUAL
19
Figure 11: SNMP General
Setup SNMP Port
1. Access the Web interface and login.
2. Under SNMP Managers, select SNMP Port. The SNMP Port page displays.