Pantech G700 User manual

G700 USER MANUAL

Characteristic Specification
Display
Clamshell TFT LCD.
Main LCD : 65,000 TFT Color Display (128 X 128)
animation message, variable Icon
Melody
On board Midi sound
Dimension & Weight
80*40*20.9mm with Slim Battery
under 80g target with Slim Battery
Performance
Talk time: up to 180 minutes (with 680 mAh Battery)
Standby time: up to 200 hours (with 680 mAh Battery)
AOL Tegic Solution T9
Chinese (Simplified), English
Operating Frequency
GSM 900MHz / DCS 1800MHz Dual Band

Caution
For the safety of You and the proper operation of units, please ensure you read the
guidelines that follow. For more details, please refer to the appendix.
Antenna
If you use antennas which are not approved by the manufacturer of the units, it may
cause a malfunction or serious damage of the unit.
Traffic safety
Please ensure that you check out the traffic regulations on the use of mobiles beforehand.
Do not use mobiles while driving. If required, please use a hands-free kit in safe
conditions.
Electronic devices in cars
The electromagnetic waves emitted from the phone may interfere with the electronic
systems of cars.
Hands-free
If you install a hands-free kit within the area of an airbag, it may cause serious injury.
Please take this into consideration.
Electronic devices
The electromagnetic waves emitted from the mobile could affect the function of electronic
devices which are not shielded.
Medical devices
Please ensure that you turn off your mobile phone in hospitals and follow the regulations
of hospitals.
Please turn off your mobile so as not to affect pacemaker devices or other medical
devices. For other inquires about the use of mobiles in hospitals, please contact doctors
or medical device manufacturers.
In the public places

Please turn off your mobile in the public places where the use of mobiles is prohibited.
In airplanes
Please turn off your mobile before taking it on board an airplane.
If you use your mobile in an airplane, it could dangerously impact on the function of the
airplane.
Explosive gas
Please turn off your mobile in regions where any explosive gas is presumed to exist and
then follow the instructions or the contents of sign boards.
Do not disconnect the battery from your mobile in regions where any explosive gas is
presumed to exist.
User Guidelines
Do not allow other people to use your mobile without permission.
In case of the loss of theft of your mobile, please contact a service provider immediately.
If your mobile does not work properly, please bring it to the nearest service center.
Please use only approved accessories and batteries. Do not attempt to connect non-
compatible products to the unit.
The RF waves emitted from the mobile may harm the human body. Therefore please
ensure that you do not expose yourself to RF waves for protracted periods.
Please back up important content such as telephone numbers or other information.
Electromagnetic Wave Exposure
The unit consists of a electromagnetic wave transmitter and receiver. It is designed and
manufactured in respect to the suggestions made by scientific studies of an independent
scientific organization, which limit the exposure of electromagnetic waves.
Please only use batteries, chargers, and accessories approved by authorized
manufacturers so that you can follow the recommended guidelines for exposure. If you
fail to use authorized products, it means you have not followed the guidelines. Therefore,
we can not guarantee the safety of You regardless of your age and status of health.
Proper Usage
Please use your mobile in the proper manner.
Do not touch or bend your antenna while using the mobile, it may harm the quality of
reception or the performance of the battery.

Do not disassemble the mobile. Non professionals could damage the mobile.
Ensure that you use only authorized or provided batteries, chargers, and accessories.
If you use unauthorized products, the warranty could be voided.

Contents
Caution
Components
Handset description
Internal LCD (Main LCD)
Function Keys
Quick start
Getting started
Basic telephone functions
Menu functions
i. Message
ii. Call logs
iii. Sound
iv. Settings
v. Net service
vi. Organizer
vii. Fun & Tools
viii. STK
ix. Phonebook
x. Hot folder
Appendix
-
How to use T9 & etc.

Components
The picture below is for the reference of users. Each item in the package could be
different according to the policy of dealers.
Themobilephone ACadapter

Handset Description
* For detail usage of key
Antenna
LCD display
Microphone
Navigation keys
Alphanumeric
ke
y
s
Menu key
Clear key
E
ar-m
i
crop
h
one
OK key
Side keys
P
ower
Ad
aptor
C
onnectors
Earpiece

Internal LCD (Main LCD)
The main-LCD is divided into two parts of screen. One screen lines up a group of icons
showing the status of the unit, while the other screen shows messages, telephone
numbers, icons, etc
<Main LCD Screen>
When a particular function is activated or a message is received, each applicatble icon is
shown.
The icons shown above are the maximum number of icons which can be displayed at the
top.
The definition of icons with pictures is explained as below.
Signal Power This icon indicates the level of RF signal. The number of bars
is different according to the power of the signal received.
Line is busy This icon indicates that the line is busy.
Melody This icon indicates that the ringer is in melody mode.
Vibration
This icon indicates that the ringer is in vibration mode or
manner mode (vibration mode: blue color, manner mode: red
color).
Vibration+Melo
dy
This icon indicates that the ringer is in melody mode after
vibration mode.
SMS message This icon indicates when messages have not been read. This
icon blinks when the messages saved in the SIM are full.
Alarm This icon indicates that the alarm is set
Roaming This icon indicates that the roaming system is supported.
Battery This indicates the level of the battery.
Function keys
The table below explains the list of functional keys which have more than one feature

Function keys
Key Icon Name Key Function
SEND KEY
Press this key when you attempt to make or take calls. (Except
for in the case when the receiving call is set as “Any Key
Answer” type).
Keep pressing this key for a moment when you want to recall
the last number.
Press this key once when you would like to check out the last
called number.
END KEY
Press this key when you would like to end a call or convert to
standby mode from Menu mode.
If you keep pressing this key for a moment, the power of the
unit either turns on or off.
OK KEY Press this key to choose or carry out a Menu option shown on
the screen.
MEMU KEY Pressing this key leads you to the main Menu.
CLEAR KEY
Press this key briefly to delete a message, or keep pressing
this key for a moment to delete a whole sentence.
Press this key if you would like to go to the previous Menu.
NAVIGATION
KEYS with
shortcut
keys to WAP,
Sound
setting,
Message
and
Phonebook
Press one of the 4 keys for left, right, Up, or Down as you want
to move when you would like to change the position of the
cursor in Menu list or editor.
If you press the [Up] key while talking on the phone, it shows
the last number received, and pressing the [Down] key, shows
the list of missed calls.
If you press this key in the initial screen, you can get easy
access to the phonebook, Sound setting, SMS, My Menu, (Hot
Folder) Menus.
SIDE UP and
DOWN KEYS
Press this key if you would like to adjust the volume of the
conversation.

WAP KEY If you press this key in the initial screen, you can directly access
the [WAP] Menu

Quick start
If you use the unit for the first time, please follow the procedures
as below. :
Put the SIM card within the unit.
If a user is registered to the network provider, he/she is
supposed to be provided with a ‘plug-in SIM’ which contains the
user’s registration information. (PIN, the existence of additional
service, etc).
If required, keep pressing the [END] key until the message of
power off appears.
1. Separate the battery from the unit.
2. After checking whether the SIM slot is empty, put the SIM card
into the slot.
3. If you would like to remove the SIM card, please push the SIM
card in the direction of the arrow shown in the picture as below.

Battery Installation
As shown in the picture below, put the metal locators of the
battery into the holes located in the bottom of the unit.
1. Insert the metal locators of the battery into the hole located in
the bottom of the unit.
2. Press the Upper part of the battery until the sound of a ‘click’
is heard.
Battery Recharging
The power of the unit is supplied by the Li-ton battery charged.
Ensure that you use only authorized batteries and chargers. For
more details, please inquire at the nearest dealer.
The unit can be used while being recharged.
When the battery is installed in the unit, open the cover and
connect an adapter to the outlet located in the lower part of the
unit. An adaptor is provided together with the unit
When finishing recharging, separate the adaptor connection
from the outlet located in the lower part of the unit.

Getting started
1. Unit power on
Press the [END] key for a moment (approximately 3 seconds) in order to turn on the
power of the unit.
2. Unit power off
Press the [END] key for a moment in order to turn off the power of the unit.
3. Making calls
Press the [END] key for a moment in order to turn on the power of the unit.
If a message “Insert SIM card” appears, insert the SIM into the SIM slot.
Unlock the handset by inputting the PIN (maximum 8 letters) when applicable
If a wrong PIN is inputted, the system automatically detects the network the user belongs
to.
Press the telephone number including the area code in the initial mode. Then attempt to
make a call by pressing the [Send] key. If you would like to make overseas calls, press
the [0] key until the sign ‘+’ appears and then input the country code, area code,
telephone number in your order. You can insert the sign ‘P’ between each code and
telephone number in order to have approximately 2 seconds of pause by pressing the
[#] key. You can make emergency calls without a SIM. If you input the number 112 and
press the [Send] key, you can make an emergency call.
4. Finishing calls
Pres the [END] key if you would like to cancel or finish your call.
5. Taking calls
When the unit rings in a melody or vibrates, if it has network service, the name or the
telephone number of the caller appears on the screen. The screen says the name only
when you have the number and name saved in the Phone Book. Press the [SEND] key if
you would like to take a call in general mode. If the receiving mode is set to [Any key],
You can take calls by pressing any key except for the [END] key.
6. Adjusting the volume of conversations

If you would like to adjust the volume of conversations while using the unit, adjust the
volume by pressing the volume key on the side of the unit for up to 8 steps as you wish.
7. Searching the main Menu
If you would like to move to the main Menu in the initial screen, press the [Menu] key.
Press the [End] key if you would like to escape from the Menu and return to the initial
screen.
You can select one of the items in the Menu by pressing the Navigation key [Up][left]
and [Down][right].
You can reply to questions with ‘Yes’ by pressing the [OK] key, and ‘No’ the [Clr] key.
8. Inputting letters and number in the handset
If you would like to input a number, select the number key pad you desire to input. If you
input a number in the handset, the system should be in ‘T9’ mode. (i.e. Phone book,
Message). For more details, please refer to the ‘T9’ page. If you would like to delete a
wrongly inputted letter, press the [Clr] key and to delete a whole sentence, keep pressing
the [Clr] key for a moment. If you keep pressing the [Clr] key for a while, all the letters in
the screen are deleted.

Basic Telephone Functions
1. Speed Dial
There are two ways to make a call in the initial screen. One is to press [Send] normally
after inputting a telephone number. The other is to use speed dial.
When making calls by using speed dial, you should press the index number for a moment
which is allocated when saved in the Phone Book of the unit. Then, the telephone number
matching the index number is attempted to be called. For example, if the index number
saved in the Phone Book of the unit is 5, press the number [5] key for a moment, then
the applicable telephone number will be attempted to be called. The scope of the index
available for speed dial is up to 99.
2. Making overseas calls
If you would like to make overseas calls, press the [0] key twice at first so that sign ‘+’
appears on the screen and then press the country code after the sign.
3. Making emergency calls
Input number 112 (emergency number) and press the [SEND] key. If you belong to the
GSM net, regardless of the existence of a SIM card, making emergency calls is available
in any country.
4. Hold calls
When you can not take a call for some reason, the unit displays a call message which
shows you have missed a call on the screen. If you would like to get back to any missed
calls, first select the [MENU]-[Call logs]-[Missed calls] keys in order. Then select a
number by using the [Up/Down] key that the user desires to get back, and press the
[SEND] key. A call will be made to the number selected.
5. Access to the Phonebook from the initial screen
You can move to the lower Menu of the unit by pressing the Down key of the Navigation
key in the initial screen without going via the Menu
6. Check out the latest number received
If you would like to check out the list of latest numbers taken or made, press the [SEND]
key. If you would like to make a call to any number from the list, press the [Up/Down] key
to select the applicable number and then press the [SEND] key and a call will be made. If

you press the [OK] key, the information of the number selected will appear.
7. Holding calls
(This function is available only for users who are registered to the internet service
provider.)
When taking calls, you can select a calling option by pressing the [MENU] key.
[MENU]
1. Answer
2. Reject
3. I am busy
If you take another call while talking on the phone, you can select one of the options
according to your situation.
Press the [End] key, if you would like to finish the current conversation.
Press the [Send] key if you would like to hold the current conversation and connect to
another call received.
8. Options while taking a call
Press the [MENU] key if you would like to use the option while taking a call.
[Menu]
1. Phonebook
2. Messages
3. Volume
4. Hold
5. End current
6. Mute on
7. DTMF on/off
The following explain each function of the above.
Hold – This option allows you to attempt another call while keeping the current call.
End current – by selecting this option, you can finish the current call.
Mute – this option allows the other party not to hear you while the user is taking another
call.
DTMF on/off –you can turn on or off the DTMF tone with this option.

Menu functions
Menu Type
The unit provides two different types of Menu. One is a basic main Menu and the other is
a hot folder (short cut) Menu.
The basic way to access to the main Menu is to press the key.
To access the hot folder Menu, press the key or the key.

1. Messages
1. SMS/EMS
EMS (Enhanced Messaging Service) is formed based on SMS (Short Message Service).
You can create a text message (SMS) including pictures, animation, melodies, messages,
and emoticons through EMS. The characteristics of the lettering can also be adjusted.
Before starting
You, first ensure that the number of the service center is set. This number is normally
provided by dealers and saved in the SIM card.
[MENU]
1. Create (writing message)
2. Inbox (received message)
3. Outbox (sent message)
4. Settings (configuration settings)
5. Used space (SIM capacity)
Create – you can write messages including items
Inbox – displays the list of received messages
Outbox
– displays the list of sent messages
Settings – Please refer to the contents that follow.
Used space – shows the condition of the SIM card.
(the total capacity of the SIM, the number of used messages, the number of unread
messages)

Settings’ detailed functions
[MENU]
1. Message center
2. Message lifetime
3. Message format
Message center – Authorization of the URL of proxy relay or set MMSC.
Message lifetime – Adjustment of the lifetime of messages (1hour~6 months)
Message format – General, fax, voice mail, ERMES, National paging, X.400, Internet)
Used space detailed functions
1. Capacity
2. Used records
3. Unread records
Capacity – displays the maximum number of messages that the SIM can save
Used records – displays the number of messages saved in the SIM.
Unread records – displays the number of messages unread.
Message check in Inbox, Outbox, Archive
1. Inbox (received messages)
1. If you press the [OK] key after selecting the “Inbox” Menu, the list will then be
displayed.
The list displays callers’ numbers corresponding to the names saved in the Phone
Book.
2. Press the [OK] key to select the message from the list of the “Inbox”.
3. The selected message appears. If the message includes any items, when
positioning the cursor at the item, for Animated parts, it moves and for Melodies,
it makes sounds.
4. If you press the [Menu] key, Menus such as “Edit”, “Delete”, “Forward”, ”Text
Reply” or “Voice call” pop up and you can select any Menu as desired.
2. Outbox (sent messages)