Paradyne 9109 User manual

1
9109 Sync Data Application Module (APM)
Installation Instructions
Document Number 9109-A2-GN10-50
August 2000
Product Documentation on the World Wide Web
We provide complete product documentation online. This lets you search the
documentation for specific topics and print only what you need, reducing the waste of
surplus printing. It also helps us maintain competitive prices for our products.
Complete documentation for this product is available at www.paradyne.com.
Select
Library → Technical Manuals → FrameSaver Frame Relay Devices or
NextEDGE Multiservices Access System .
Select the appropriate document:
9161-A2-GB20
Model 916x/926x T1 Access Mux User’s Guide
9161-A2-GH30
Model 916x/926x T1 Access Mux Technical Reference
9191-A2-GB20
FrameSaver SLV Multiservices Access Unit, Models 9191, 9192, and 9195, User’s
Guide
To order a paper copy of a Paradyne document:
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
Outside the U.S.A., call 1-727-530-8623
Before You Begin
Make sure you have:
The housing, and any associated hardware, already installed
The housing installation instructions
A T1 NAM already installed in Slot 01 and connected to the network
Applicable cables
A small Phillips screwdriver (#1 or #2) to install the APM
A small, flat-blade screwdriver to install the I/O card and cable connections

2
See the appropriate product manual for additional information on:
Troubleshooting
Technical Specifications
Connectors, Cables, and Pin Assignments
Package Checklist
Verify that your package contains the following:
4-Port Sync Data APM
4-Port Sync Data I/O card
When your equipment arrives, inspect it for physical damage and tighten any screws
that may have worked loose. Contact your sales representative immediately if there are
any signs of shipping damage or if anything is missing from your package. Otherwise,
proceed with the installation.
Equipment You May Need to Order
The following cables and connectors are specifically for this product. For additional
information, see
Equipment List in the appropriate document.
If connecting
to a . . . Order a . . . Feature No.
DTE with a V.35
interface/connector MS34-to-DB25 adapter cable for each port: Port 1, Port 2, Port 3, and/or Port 4
(1 foot/.31 meter)
3100-F1-570
DTE with an RS-449
interface/connector DB37-to-DB25 adapter cable for each port: Port 1, Port 2, Port 3, and/or Port 4
(1 foot/.31 meter)
3100-F1-580
DTE with a V.11/X.21
interface/connector DB15-to-DB25 adapter cable for each port: Port 1, Port 2, Port 3, and/or Port 4
(1 foot/.31 meter)
3100-F1-571

496-15149
PORT 4
9109 Sync
PORT 3
Port 1
Port 2
Port 3
Port 4
97-15167-01
PORT 2
PORT 1
3
!HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from
damage due to electrostatic discharge (ESD) during normal
operation. When performing installation procedures,
however, take proper static control precautions to
prevent damage to equipment. If you are not sure
of the proper static control precautions, contact
your nearest sales or service representative.
Installing the I/O Card
The 4-port I/O card provides the APM with DTE connections. The I/O card inserts
directly behind the APM that it supports. Slot numbers are identical to facilitate correct
installation.
1. Remove the I/O card from the shipping box. Handle only by
the top and bottom edges to avoid damaging the card.
2. At the rear of the housing, align the I/O card with the upper
and lower tracks of the slot. Push gently towards the
midplane until it stops and you cannot push the card any
further.
98-15150-02
Rear View
Screws
5-Slot 2-Slot
3. There are two captive screws on the I/O card. Using a
small, flat-blade screwdriver, alternately tighten each screw
until both are snug.

4
Connecting to a DTE
If the DTE cable type is EIA-530A:
1. Connect the EIA-530A end of the DTE cable to PORT 1, PORT 2, PORT 3, or
PORT 4.
DTE V.35, RS-449,
V.11/X.21
Adapter Cable
EIA-530A
Cable
DTE
or
496-15153
If the DTE cable type is V.35, RS-449, or V.11/X.21 (all separately orderable):
1. Connect the plug to the V.35, RS-449, or V.11/X.21 end of the adapter cable.
2. Connect the EIA-530A end of the adapter cable to PORT 1, PORT 2, PORT 3, or
PORT 4.

98-15174-01
Front View
(without Bezel)
Power
Supply
5
Removing the Housing’s Bezel
1. Depress the latch at the top of the housing to open the bezel.
2. Lift upward to remove the bezel from the two slots at the bottom of the housing.
496-15123
Save the bezel so it can be reattached once the APM has been installed.
NOTE:
The power supply is visible once the bezel is
removed. It provides low voltage power to the
housing and its cards.
!WARNING:
If you need to remove the power supply
module, you must unplug the power cord
from the power receptacle and from the rear
of the housing before attempting to remove
the module.

6
Installing the APM
The APM can be installed in any slot except Slot 01.
CAUTION:
You must insert the Synchronous Data APM in the correct slot so that it
mates with its matching I/O card. APMs are keyed so that they mate only with
their matching I/O cards.
1. Remove the filler panel, if applicable. See the installation instructions that came
with your housing for information.
2. Remove the APM from the shipping box. Handle only by the top and bottom edges
to avoid damaging the card.
3. At the front of the housing, align the APM with the upper and lower tracks of the
selected slot.
98-15152-02
Ejector
Latches
Ejector
Latches
5-Slot 2-Slot
FrontView
4. Slide the APM into the tracks until it seats with the midplane connectors. Be careful
not to force the card or bend any pins.
5. Close both the upper and lower ejector latches on the housing to lock in place, then
tighten the captive screws.
Reinstalling the Bezel
1. Insert the bezel into the two slots at the bottom of the front of the housing.
2. Snap the bezel in place using the latch at the top.

7
Removing/Replacing a Card
Card removal procedures differ, depending on whether you are removing the APM or
I/O card.
NOTE:
You can insert or remove the APM and its associated I/O card without powering off
the equipment and interrupting data flow through other cards in the system.
Removing/Replacing an APM
1. Remove the housing’s bezel, if applicable. See the installation instructions that
came with your housing for information.
2. Remove the captive screws from the ejector latches on the front of the housing.
3. Press open the ejector latches to disengage the card from the midplane.
4. Supporting the card by its edges, pull straight out until the card clears the housing.
5. Refer to Steps 3–5 of
Installing the APM on page 6.
When replacing an APM, be aware of the following:
If the slot . . . Then the . . .
Was previously unassigned Configuration settings are the factory defaults and are
accessible from SNMP and the user interface.
Was previously assigned to
the same type of APM Existing configuration settings are used and are accessible from SNMP and the user interface.
Previously contained a
different type of APM System generates a Module Misconfiguration alarm for the given slot. See the appropriate document
for procedures in this situation.
Removing/Replacing an I/O Card
1. Remove the APM from the housing (see Removing/Replacing an APM on
page 7).
2. Remove the DTE cables from the I/O card.
3. Using a small flat-blade screwdriver, loosen the upper and lower captive screws
fastening the card to the housing’s frame.
4. Gently pull the I/O card away from the midplane until it clears the housing.
5. Align the replacement card with the upper and lower tracks of the slot. Push gently
towards the midplane until it stops and you cannot push the card any further.
6. Alternately tighten each captive screw until both are snug.
7. Reattach the cables as appropriate.

8
Power-On
Refer to the installation instructions that came with your housing to power on the
equipment.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for
any help needed. For additional information concerning warranty, sales, service, repair,
installation, documentation, training, distributor locations, or Paradyne worldwide office
locations, use one of the following methods:
HInternet: Visit the Paradyne World Wide Web site at www.paradyne.com.
(Be sure to register your warranty at www.paradyne.com/warranty.)
HTelephone: Call our automated system to receive current information by fax or to
speak with a company representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them
to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,
or send e-mail to [email protected]. Include the number and title of this
document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.
Trademarks
FrameSaver and NextEDGE are a registered trademarks of Paradyne Corporation. All
other products and services mentioned herein are the trademarks, service marks,
registered trademarks, or registered service marks of their respective owners.

*9109–A2–GN10–50*
Copyright E2000 Paradyne Corporation. Printed in U.S.A.