Paramount Fitness BLT-999A-2 User manual

1-800-561-5550
[email protected]
ELECTRIC FIREPLACE
INSERT
INSTRUCTIONS FOR USE
Item number: EF-128-5
Model number:BLT-999A-2
READ & SAVE THESE INSTRUCTIONS
Carefully read and review before assembling, installing,
operating or maintaining this product. Observe all safety
instructions and information.
FAILURE TO FOLLOW WARNINGS & OPERATIONAL
INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT
IN PROPERTY DAMAGE OR PERSONAL INJURY.
**IMPORTANT NOTICE**
Please contact our toll free hotline:
For customer service & warranty issues
R
US

Always plug heaters directly into a wall outlet/receptacle.
Never use with an extension cord or relocatable power tap
(outlet/power strip)
22/ This electric fireplace is not designed for "zero" tolerance wall and/or
cabinet/millwork installations. Accessability for servicing and maintenance
must be possible without disturbing building structure and/or cabinet/
millwork finishes. Allow 6cm/2.4" clearance from the top of the insert to any
building material surface and 3cm/1.18" clearance from the sides to any
buildling material surface.

Dimensions W x D x H : 30.7” x 9.8” x 25”
Net Weight 42.2 lbs / 19.2 kg
Gross Weight 46.6 lbs / 21.2 kg
Voltage 110 – 120 V
Frequency 60 Hz
Watts 1400 W
Heater Rating 4774 BTUs

Always plug heaters directly into a wall outlet/receptacle. Never use
with an extension cord or relocatable power tap (outlet/power strip)
Figure 2
The cord has a plug as shown in (A) of Figure 2 given below.
T

replace insert control functions can be accessed in 2 ways:
1. Using a remote control
2. Using the manual contr replace insert.
replace insert features conveniently separate contr ect and for heat control.
This feature allows you to operate the unit in 2 di erent ways:
As a
full featured insert with both the e ect and heater on.
As elausiva ect with the e ect only.
Refer to the pictures for location of the buttons on both the remote contr replace insert itself.

Low heat 750 watts
High heat 1400 watts
REMOTE CONTROLS
1. Heater Timer: Allows you to leave your heater
on with an automatic timer for shut
off. You can set your heater to be on for 1/2 hour
increments starting at a 1/2 hour up to a maximum
of 7-1/2 hours – press once for each 1/2 hour
increment. After you reach 7-1/2 hours the next
press will shut off the feature.
2. Flame brightness controls: Allows you to
ress to
incrrease
You must press the button
five times to see the full ame effect
3.  
4. Heater Control: ress once for low heat, and
twice for high heat.
4

replace insert uses 3 clear 120 Volt, 40 Watt, E-12 socket base light bulbs (small base, chandelier candle type
bulbs). The lights are located at the bottom of the unit. For convenience, if one of the light bulbs burns out, it may be
easier to replace all 3 of the light bulbs at the same time.
WARNING: Do not exceed 40 Watts per bulb. Use of higher rated bulbs may r re, causing property
damage, personal injury or loss of life.
1. Tur n o the power to the unit.
2. replace insert cool if it has been operating.
3. Gently pull the mantel away fr replace
. T rebox by the side handles and slide it out
of the mantel. Be careful not to scratch the mantel base.
4. lliwuoY.uoygnicafmottobehthtiwkcabstinotinuehteil,letnamehtfoeerftresniecalper
see 2 plates with gold printing indicating the bulbs are behind these plates.
5. Remove the 2 screws on each plate with an appropriate screwdriver. Once you have removed the 4 screws
slightly lift each plate until you can pull back and release the plate. Once you have removed
the plates you can see and access the 3 - 40 Watt bulbs.
6. Remove each light bulb by unscrewing them out of the bases, turning them counterclockwise. You can use one
hand to hold the light socket in place, if required.
7. Install the new light bulbs by turning each light bulb into the base clockwise. You can use one hand to hold the light
socket in place, if required.
8. Replace each cover plate by inserting the tabs and lowering the plate.
9. Replace the 2 screws in each plate that were removed in Step 5, by using an appropriate screwdriver.
10. replace insert up on its bottom.
11. replace insert back on to the mantel hearth.
12. replace insert back into position against the fr replace insert
replace insert has rubber feet on the bottom to protect against
damage as long as it is level.
Bottom

6. Heater and/or flame turn off
while operating Timer function may have been on Push On/Off button to reset
4. Logs glow, but no flame Flame spinner disconnected Call customer service for
instructions
5. Flame and logs glow, but no
heat Heater switch is off Push heater button. Indicator light will come on
2. No power, no indicator lights No power at outlet Check circuit breaker or fuse
3. Power indicator lights come on,
logs will not glow and no flame
effect
Broken or burned out light bulbs Follow instructions for replacing
light bulbs
CORRECTIVE ACTION
1. No power, no indicator lights Insert was not plugged in Make sure that power cord is
plugged into 120 V outlet
PROBLEM POSSIBLE CAUSE

.
IMPORTANT
For questions, concerns or problems with our product please
email our customer service department:
[email protected]
DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE
WARRANTY
This product is inspected, tested and carefully packaged to minimize
the chance of damage during shipment. If a part (excluding light
bulbs, glass and fuses*) within one year from the date of purchase
proves to be defective in material or fabrication under normal use,
the part will be repaired or replaced. The Company’s obligation under
the warranty is to replace or repair defective parts at our discretion.
Any expenses or damage resulting from the installation, removal or
transportation of the product will be the responsibility of the owner
and are not covered by this warranty. The owner assumes all other
risks arising from the use or misuse of the product. The warranty will
be void if the product damage or failure is deemed by the Company
to be caused by accident, alteration, misuse, abuse, incorrect
installation or removal, or connection to an incorrect power source
by the owner. The Company neither assumes, nor authorizes any
person or entity to assume for it any obligation or liability associated
with its products. Light bulbs and fuses are not covered under this
warranty. If you have any questions regarding the warranty or service,
please contact us at [email protected]
Customer Service:
JR Home Products
Unit 306 - 19100 Airport Way, Pitt Meadows, BC V3Y 0E2
Toll Free: 1-800-561-5550
E-mail: [email protected]
Warranty Registration Information Form / Formulaire d’enregistrement de la garantie
Registration can be completed online at
www.jrhome.com or by mailing this form.
Name / Nom:
Street / Adress:
City / Ville:
Province / Province:
Postal Code / Code postal:
Daytime Phone # / No téléphone jour:
Evening Phone # / No téléphone soir:
E-Mail Address / Courriel:
Product/Produit:
Place of Purchase / Lieu de l’achat:
Date of Purchase / Date de l’achat:
Model # / No de modèle:
Serial # / Numéro de série:
You MUST register your product to receive
warranty service.
For warranty service, contact J&R Home
Products at the address, phone numbers listed
below within 30 days of purchase. Be sure to
have your sales receipt and original date of
purchase. All warranty service will be
coordinated by
J&R Home Products service center.
Vous DEVEZ enregistrer votre produit pour vous
prévaloir de la garantie.
Afin de faire valoir la garantie, communiquez
avec J&R Home Products à l’adresse et aux
numéros indiqués ci-dessous dans les 30 jours
suivant la date d’achat. Ayez en main votre reçu
et la date d’achat. Toutes les demandes liées
aux garanties seront traitées par le centre de
service de J&R Home Products.
Please mail to / Veuillez poster le tout à : Parts & Service Department, J&R Home Products Ltd. Unit 306 - 19100 Airport Way, Pitt Meadows, BC V3Y 0E2
You MUST register your product to receive warranty service.
Si vous éprouvez des dicultés, ou si vous avez des questions ou des
préoccupations, prière de faire parvenir un courriel à notre Service à la clientèle
[email protected]
UNE PREUVE D’ACHAT DATÉE EST REQUISE POUR SE PRÉVALOIR DE LA GARANTIE.
AVERTISSEMENT
les risques de, dommages durant le transport. Si l’une des pièces (à
l’exception des ampoules électriques verre et des fusibles*) s’avère
défectueuse au niveau de sa fabrication ou de ses matériaux dans l’année
qui suit la date de l’achat, suite à une utilisation normale, la pièce sera
réparée ou remplacée. La Compagnie est tenue de réparer ou remplacer les
pièces défectueuses, à sa discrétion, en vertu de la garantie. Tout frais ou
dommage résultant de l’installation, du démantèlement ou du transport du
produit demeure la responsabilité du client et n’est pas couvert par cette
garantie. Le client assume tout autre risque résultant de l’utilisation, correcte
ou fautive, du produit. La garantie devient nulle si la Compagnie détermine
que le dommage ou le mauvais fonctionnement est causé par un accident,
une modication, une mauvaise utilisation ,un abus, une mauvaise
installation ou un mauvais démantèlement ou un branchement à une
source électrique inadéquate de la part du client. La Compagnie n’est pas
responsable et n’autorise quiconque, personne ou entité légale, à accepter
de responsabilité ou obliga-tion en son nom, en rapport avec ses produits.
* Les ampoules électriques et les fusibles ne sont pas couverts par cette
garantie. Pour toute question en rapport avec la garantie ou le service,
envoyez-nous un courriel à: [email protected].
Service à la clientèle :
JR Home Products
Unit 306 - 19100 Airport Way, Pitt Meadows BC V3Y 0E2
Toll Free: 1-800-561-5550
E-mail: [email protected]
L’enregist rement sera complet une fois que vous
aurez posté ce formulaire ou s’inscrire en linge à:
Vous DEVEZ enregistrer votre produit pour vous prévaloir de la garantie.