Paramount Fitness ES10006 User manual

ELECTRIC FIREPLACE INSERT
ES10006
FOR CUSTOMER SERVICE CONTACT
[email protected]
OR 1-800-561-5550
1
AEY R
Y
W
T
A
N
R
A
R
m di etli
* Save this manual for future reference.
R
CUS
INSTRUCTION MANUAL
IMPORTANT SAFETY
INSTRUCTIONS
&
Approved for use in
Canada and the United States

WARNING: All electric heaters have
hot and arcing or sparking parts inside.
Do not use it in areas where gasoline,
paint or flammable liquids are present.
WARNING: This electric fireplace is
tested and listed for use only with the
optional accessories listed in these
instructions. Use of optional
accessories not specifically tested for
this electric fireplace could void the
heater warranty and/or result in a
safety hazard.
This electric fireplace meets the
construction and safety standards of H.U.D.
for application in manufactured homes when
installed according to these instructions.
2
!
!
Read these instructions completely before
beginning installation. Failure to follow
them could cause a heater malfunction
resulting in serious injury and/or property
damage.
Electric fireplace inserts and free standing
electric fireplaces heaters rated at 1500w/ 5000 BTU

Important Safety Instructions.....................................................
Listing Approvals .....................................................................
Product Dimensions .................................................................
Locating Fireplace ..................................................................
Unpacking and Testing Fireplace .............................................
Grounding Instructions............................................................10
Installation ............................................................................
Operating Instructions ............................................................
Maintenance ........................................................................
.
Troubleshooting ....................................................................
Warranty ...............................................................................
3
TABLE OF CONTENTS
4
7
8
9
10
11
12
13
16
17
.
Replacement Parts ..................................................................
....................................................
14
15
Replacement Parts Diagram ..

4
IMPORTANT SAFETY INSTRUCTIONS
Prior to plugging your heater into an electrical outlet,
verify that the house circuit breakers for the outlet are
on.
The heater may emit a slight, harmless odor when first
used. This odor is normal and it is caused by the initial
heating of internal heater elements and will not occur
again.
If your heater does not emit heat, consult the operation
section of this manual for further information.
Use with a CSA or UL certified surge protector.
KEEP DRAPERY AND OTHER FURNISHINGS AT
LEAST 3 FEET (0.9m) FROM THE FRONT AND
SIDES OF THE HEATER.
CAUTION: High temperature, risk of fire.
Keep electrical cords, drapery,
furnishings, and other combustibles at
least 3 feet (0.9m) from the front of the
heater and away from the side and rear.
WARNING: Servicing should be done only
while the heater is disconnected from the
power supply circuit.
1/
2/
3/
!
!
SA1965 SA1965
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
HIGH TEMPERATURE
KEEP ELECTRICAL CORDS
4/

5
Read all instructions before using this electric fireplace.
Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes and curtains at least 3 feet
(0.9m) from front of heater and keep them away from sides
and rear.
Always unplug electric fireplace when not in use.
Do not operate this electric fireplace with a damaged cord or
plug or after heater malfunctions, has been dropped or
damaged in any way. Return heater to authorized service
facility for examination, electrical or mechanical adjustment or
repair.
Do not use this electric fireplace outdoors.
This electric fireplace is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never locate
electric fireplace where it may fall into a bathtub or other water
container.
Do not run cord under carpeting. Do not cover cord with throw
rugs, runners or the like. Arrange cord away from traffic area
and where it will not be tripped over.
To disconnect electric fireplace, turn controls to "OFF" before
removing plug from outlet.
This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. If provided, use handles when moving
this heater.
Extreme caution is necessary when any heater is used by or
near children and whenever the heater is left operating and
unattended.
Connect to properly grounded outlets only.
When using this electric fireplace, basic precautions should always
be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
1/
2/
3/
4/
5/
6/
7/
8/
9/
10/
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT INSTRUCTIONS

Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock or fire
or damage the heater.
To prevent possible fire, do not block air intakes in any
manner.
The electric fireplace has hot and arcing or sparking parts
inside. Do not use it in areas where gasoline, paint or
flammable liquids are used or stored.
Use this electric fireplace only as described in this manual.
Any other use not recommended by the manufacturer may
cause fire, electric shock or injury to persons.
Avoid the use of an extension cord because the extension
cord may overheat and cause a risk of fire. However, if you
have to use an extension cord, the cord should be No. 14 AWG
minimum size and rated not less than 1875 WATTS.
Do not use on soft surfaces, like a bed, where
openings may become blocked.
Always use properly grounded fused and polarized outlets.
Always use ground fault protection where required by
electrical codes.
Always disconnect power before performing any cleaning,
maintenance or relocation of heater.
To prevent a possible fire, do not burn wood or other materials
in this electric fireplace.
To prevent electric shock or fire, always hire a certified
electrician should new circuits or outlets be required.
When transporting or storing this electric fireplace, keep in a
dry place free from excessive vibration and store as to avoid
damage.
6
12/
13/
14/
15/
16/
19/
SAVE THESE INSTRUCTIONS!
IMPORTANT SAFETY INSTRUCTIONS
11/
20/
21/
18/
17/

LISTING APPROVALS
This heater has been tested in accordance with the CSA Standards for
fixed and location-dedicated electric room heaters in the United States
and Canada. If you need assistance during installation, please contact
your local dealer.
Note: This heater
must be
electrically wired
and grounded in
accordance with
local codes or, in
the absence of
local codes, with
National Electric
Code ANSI/NFPA
70-latest edition
or the Canadian
Electric Code,
CSA C 22 .1 as
appropriate.
Description: Portable Stove
Voltage: 120V AC
MAX 1500W
LED
Watts:
Lamp:
18.11''( )
12’' ( )
Length:
Height:
Depth:
Net Weight:
Gross Weight:
27.75 lbs ( )
34.98 lbs ( )
Mode l Numbe r: DBL-2000-YM4
7
25.28’' ( )
C : 20.87"WX15.04"DX29.92"H
arton Size
z
z
z
15.88kgs
12.6kgs
305mm
642mm
460mm
'''' '' ''

305mm(12”)
460mm(18.11”)
642mm(25.28”)
PRODUCT DIMENSIONS
8
Figure 1
Fireplace Dimensions
FRONT VIEW
BACK VIEW
TOP VIEW
SIDE VIEW
Heater Vents
(DO NOT COVER)

WARNING: Due to high temperatures, this electric fireplace
should be located out of traffic. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the front of the heater.
WARNING: Never locate this electric fireplace where it
may fall into a bathtub or other water container.
NOTICE: Minimum clearance of 1" on
all sides must be maintained at all
times. Illustrations throughout these
instructions reflect typical installations
and are for design purposes only.
Actual installations may vary slightly
due to individual preferences.
CAUTION: Do not
expose the electric
fireplace to the
elements
(such as rain, etc.)
CAUTION: Wear
gloves and safety
glasses for protection
during installation and
maintenance.
Figure 2 illustrates a variety
of ways the fireplace may be
located in a room. The heater
may be installed directly on
the floor, or raised on a
hearth.
LOCATING FIREPLACE
WARNING : To prevent
contact with sagging or loose
insulation, the electric
fireplace must not be
installed against vapor
barrier or exposed
insulation. Localized
overheating could occur and
a fire could result.
9
!
!
!
!
!
Figure 2
Heater Locations

Carefully remove the unit from the box. Prior to installing
the unit, test to make sure the unit operates properly. To do
this, plug the unit's power supply cord into a conveniently
located 120-Volt grounded outlet.
UNPACKING AND TESTING FIREPLACE
10
Figure 3
Grounding Methods
GROUNDING INSTRUCTIONS
This appliance is for use on 120 Volts. The cord
has a plug as shown in (A).
To disconnect appliance, turn controls to off, then
remove plug from outlet.
(A)
GROUNDING PIN
COVER OF
GROUNDED
OUTLET BOX

WARNING: RISK OF FIRE! To prevent a possible fire, do not
block air intake or exhaust in any manner. Do not use on soft
surfaces where openings may become blocked.
WARNING: RISK OF FIRE! Do not blow or place insulation
against the fireplace.
WARNING: This electric fireplace is tested and listed for use
only with the approved optional accessories. Use of optional
accessories not specifically tested for this electric fireplace
could void the heater warranty and/or result in a safety
hazard.
INSTALLATION
WARNING: RISK OF FIRE! The power cord must not be
pinched or against a sharp edge. Secure cord to avoid tripping
or snagging to reduce the risk of fire, electric shock or
personal injury. Do not run cord under carpeting. Do not cover
cord with throw rugs, runners or the like. Arrange cord away
from traffic areas and where it will not be tripped over.
WARNING: If the infor-
mation in these
instructions is not
followed exactly, a fire
or explosion may result
causing property
damage, personal injury
or death.
Do not store or use
gasoline or other
flammable vapors in the
vicinity of this or any
other heater.
11
!
!
!
!
!

OPERATING INSTRUCTIONS
12
Main Power and Flame
Switch: This switch is located
on the right side of the control
panel on the bottom of the unit.
The "|" indicates ON and "O"
indicates OFF. Push the switch
to "|" and the switch will glow in
red to indicate the unit and the
flame effect is turned on.
Heater ON/OFF Switch: This
switch is located to the left of
the Main Power and Flame
ON/OFF switch on the control
panel on the bottom of the unit.
The "|" indicates ON and "O"
indicates OFF. Push the switch
to "|" and the heater will be
turned on. To set the desired
heater setting, refer to 3/ below.
Heater Level Adjustment
Switch: This switch is located to
the left of the Heater ON/OFF
Switch on the control panel on
the bottom of the unit. " ”
indicates "LOW" setting (750W)
and " | " indicates "HI" setting
(1500W). Push the switch to " "
to set the heater on the LOW
setting and push the switch to "
" to set the heater on the HI
setting.
ON/OFF
O
O
|
1/
2/
The controls are located on the bottom of the unit. Figure 4
illustrates the location of the controls.
Once the unit has been properly connected to a grounded
electrical outlet, it is ready to operate.
Note: ensure the house circuit breakers for the power
supply are turned on.
Figure 4
Operating Instructions
3/
123
1.
2. Heater (ON/OFF)
3. Heater Level Adjustment (LOW/HI)
Power and Flame (ON/OFF)

Common Observed Problems:
There is no flame
Flame is dim or dark in certain areas
Flame is not moving or glowing
Ember bed is dim or dark in certain areas
Preparation for Maintenance
WARNING: Always disconnect the power and allow the
electric fireplace to cool completely before performing any
cleaning, maintenance or relocation of this electric fireplace.
Turn all controls to OFF and remove plug from outlet or turn
off the house circuit breaker to electric fireplace receptacle.
!
MAINTENANCE
13
This product can expose you to chemicals including Carbon
Black, which is known to the State of California to cause cancer,
and Bisphenol A (BPA), which is known to the State of California to
.
.
cause birth defects or other reproductive harm. For more information
go to www.P65 Warnings.ca.gov
W

14
Replacement Parts
FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE ONLY
PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY.
WARNING
To order parts, contact [email protected]
FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE
REQUIRED TO HONOUR THE CLAIM.
When ordering replacement parts always give the following information: 0RGHODQGVHULDOQXPEHURIDSSOLDQFH
,QVWDOODWLRQGDWHRIDSSOLDQFH
3DUWQXPEHU
'HVFULSWLRQRISDUW
)LQLVK
FOR FURTHER INFORMATION, CONTACT [email protected] or call 1-800-561-5550.
!
REF.
1
2
3
4
5
DESCRIPTION
Transformer
Ember Bed Led Light
COMPONENTS
DBL-2000-YM4
TF
BBLL
RBH
HEATER
Reflective brush combination
Blower and Heater Assembly
Switch
SH
6Motor
120V/10/12RPM

Replacement Parts Diagram
15
FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE ONLY
PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY.
WARNING
!
1
2
3
4
5
6

16
WARNING: Turn off the fireplace completely and let cool
before servicing.
TROUBLESHOOTING
!
POSSIBLE CAUSE
OBSERVED PROBLEM REMEDY
Dim or no flame 1. Le d a re burnt out
1. Inspect the led
inside the flame
generation flicker
rod a nd replace them
if necessary
Ember bed is not
glowing or dimming 1. L ed are burnt out 1. Inspect the ember
bed led and re place
them if necessary
Fi r epl ace w ill n ot co m e
on w h en sw itc h is fl i pp e d
to O N
1. Fireplace is not
plugged into an electrical
outlet
2. Fireplace has
overheated and safety
device has caused the
thermal switch to
disconnect
1. Check plug and plug
it in
2. Unplug the unit,
allow heater to cool for
10 minutes, then plug it
back in
Fireplace turns off and will
not turn on
1. Fireplace has
overheated and safety
device has caused the
thermal switch to
disconnect
2. House circuit breaker
has tripped
1. Unplug the unit,
allow heater to cool for
10 minutes, then plug it
back in
2. Reset house circuit
breaker

IMPORTANT
For questions, concerns or problems with our product please
email our customer service department:
[email protected]
DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE
WARRANTY
This product is inspected, tested and carefully packaged to minimize
the chance of damage during shipment. If a part (excluding light
bulbs, glass and fuses*) within one year from the date of purchase
proves to be defective in material or fabrication under normal use,
the part will be repaired or replaced. The Company’s obligation under
the warranty is to replace or repair defective parts at our discretion.
Any expenses or damage resulting from the installation, removal or
transportation of the product will be the responsibility of the owner
and are not covered by this warranty. The owner assumes all other
risks arising from the use or misuse of the product. The warranty will
be void if the product damage or failure is deemed by the Company
to be caused by accident, alteration, misuse, abuse, incorrect
installation or removal, or connection to an incorrect power source
by the owner. The Company neither assumes, nor authorizes any
person or entity to assume for it any obligation or liability associated
with its products. Light bulbs and fuses are not covered under this
warranty. If you have any questions regarding the warranty or
service, please contact us at [email protected].
Customer Service :
JR Home Products
Unit 306 - 19100 Airport Way, Pitt Meadows, BC V3Y 0E2
Toll Free : 1-800-561-5550
E-mail : [email protected]
Warranty Registration Information Form / Formulaire d’enregistrement de la garantie
Registration can be completed online at
www.jrhome.com or by mailing this form.
Name / Nom :
Street / Adresse :
City / Ville :
Province / Province :
Postal Code / Code postal :
Daytime Phone # / No téléphone jour :
Evening Phone # / No téléphone soir :
E-Mail Address / Courriel :
Product/Produit :
Place of Purchase / Lieu de l’achat :
Date of Purchase / Date de l’achat :
Model # / No de modèle :
Serial # / Numéro de série :
You MUST register your product to receive
warranty service.
For warranty service, contact J&R Home
Products at the address, phone numbers listed
below within 30 days of purchase. Be sure to
have your sales receipt and original date of
purchase. All warranty service will be
coordinated by
J&R Home Products service center.
Vous DEVEZ enregistrer votre produit pour vous
prévaloir de la garantie.
Afin de faire valoir la garantie, communiquez
avec J&R Home Products à l’adresse et aux
numéros indiqués ci-dessous dans les 30 jours
suivant la date d’achat. Ayez en main votre reçu
et la date d’achat. Toutes les demandes liées
aux garanties seront traitées par le centre de
service de J&R Home Products.
Please mail to / Veuillez poster le tout à : Parts & Service Department, J&R Home Products Ltd. Unit 306 - 19100 Airport Way, Pitt Meadows, BC V3Y 0E2
You MUST register your product within 30 days of
purchase to receive warranty service.
Si vous éprouvez si vous avez des questions ou des
préoccupations, prière de faire parvenir un courriel à notre service à la clientèle
[email protected]
UNE PREUVE D’ACHAT DATÉE EST REQUISE POUR SE PRÉVALOIR DE LA GARANTIE.
AVERTISSEMENT
soigneusement
des verres,
s
demeurent
service,
contacter le service à la clientèle à : [email protected].
Service à la clientèle:
JR Home Products
Unit 306 - 19100 Airport Way, Pitt Meadows BC V3Y 0E2 Numéro
sans frais: 1-800-561-5550
Courriel: [email protected]
Vous DEVEZ enregistrer votre produit dans les 30 jours suivant l'achat
pour bénéficier du service de garantie.
L’enregistrement sera complet une fois que vous aurez postéce
formulaire ou que vous serez inscrit en ligne.
120920
Extend Your Warranty By Leaving A Review
We want your opinion about your purchase...and we want you to tell everyone about it!
Just leave a review for the product on the retailers website where you made your purchase, or at www.jrhome.com, and
fill in the online warranty at www.jrhome.com/warranty-registration within 30 days of purchase to receive a complimentary
extra year of warranty protection.
Follow us on/ Suivez-nous sur:
www.jrhome.com #jrhome #paramount
JR HOME
COLLECTION

Y
W
T
A
N
R
A
R
CUS
MODE D’EMPLOI
ET CONSIGNES DE
SÉCURITÉ IMPORTANTES

!
!