Paramount Fitness JR42 User manual

Page 1
1
YEAR
limited
WARRANTY
Wall Mount Fireplace
With Adjustable Mounting Bracket
Owner’s Manual
Model Number Item Number
JR42 EF-WM353 XIN
JR50 EF-WM350 XIN
*Patented Flame Technology & Front Venting Design
READ & SAVE THESE INSTRUCTIONS
Carefully read and review before assembling, installing, operating, or maintaining
this product. Observe all safety instructions and information.
FAILURE TO FOLLOW WARNINGS & OPERATIONAL INSTRUCTIONS CONTAINED IN THIS
MANUAL CAN RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY
**IMPORTANT NOTICE**
For customer service & warranty issues, please contact: [email protected]
03.16.21
JR60 EF-WM349 XIN
JR72 EF-WM348 XIN

Page 2
Introduction
WARNING
THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance
Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before servicing. To
disconnect power to the appliance, turn controls to off, then remove plug from outlet.
Do not install damaged, incomplete or substitute components.
Do not burn wood or other materials in this appliance.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are
at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep
toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot
Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
It is imperative that the control compartments, circulating blower and its passageway in the appliance and are kept
frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area
the appliance and to replace any part of the control system which has been under water.
Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be
Do not strike or slam shut the appliance glass door.
Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic
bags, these are not toys and should be kept away from children and infants.
Servicing should be done only while the appliance is disconnected from the power supply circuit.
Always unplug appliance when not in use.
Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been dropped or
damaged in any manner. Return appliance to authorized service facility for examination, electrical or mechanical
adjustment, or repair.
Do not use outdoors.
Never locate appliance where it may fall into a bathtub or other water container.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from
Connect to properly grounded outlets only.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric
carpet, where openings may become blocked.
Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap
(outlet/power strip).
Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to
decorations, a T.V. or other electronic components.
03.16.21

Page 3
Dimensions
Listing Approvals
FRONT VIEW
TOP VIEW
SIDE VIEW
electric room appliances in the United States and Canada. If you need assistance during installation, please
contact your local dealer.
NOTE: This appliance must be electrically wired and grounded in accordance with local codes or,
in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United
States or the Canadian Electric Code, CSA C22.1 in Canada.
SNOISNEMIDNOTRACSNOISNEMIDTCUDORP
Item No. A B C D E F G Width x Depth x Height
EF-WM350 XIN 20” 4.2” 18.8” 9.72”
EF-WM349 XIN 60” 20” 4.2” 18.8” 54.10” 9.72” 51.57” 66.93” x 10.24” x 25.59”
EF-WM348 XIN 72” 23.25” 4.2” 20.27” 66.10” 10.24” 63.57”
Item No. Net Weight Gross Weight
EF-WM353 XIN 23 KGS 29.5 KGS
EF-WM349 XIN 32.5 KGS 41.5 KGS
EF-WM348 XIN 44 KGS 56.0 KGS
Description Electric Fireplace
Type 3 Way Mounting Wall Mount
Voltage 120V AC
Watts MAX 1500W
Amps 15 AMP Grounded Circuit
E
D
C
03.16.21
50” 44.10” 41.57” 56.89” x 10.24” x 25.59”
EF-WM353 XIN 42” 20” 4.2” 18.8” 36.10” 9.72” 33.58” 49” x 10.24” x 25.59”
27 KGS 34.5 KGS
EF-WM350 XIN
79.53” x 11.22” x 29.92”
A
G
FB

Page 4
General Instructions
READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO
FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE IT
IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL
ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT
SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR
RESULT IN A SAFETY HAZARD.
DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.
DO NOT USE DAMAGED ELECTRICAL CORDS.
SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE
POWER SUPPLY CIRCUIT.
TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF
RECEPTACLE AND FULLY INSERT.
1. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the
outlet are on.
2.
by the initial heating of internal appliance elements and will not occur again.
3. If your appliance does not emit heat, consult the operation section of this manual for further information.
4.
5. Do not route the power cord directly underneath the appliance.
This electric appliance meets the construction and safety standards of H.U.D. for application in
manufactured homes when installed according to these instructions.
temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the
WARNING
Unpacking and Testing Appliance
Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance
operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet.
03.16.21

Page 5
EF-WM353 XIN (42”) x2
EF-WM350 XIN (50”) x2
EF-WM349 XIN (60”) x2
EF-WM348 XIN (72”) x2
EF-WM353 XIN (42”) x1
EF-WM349 XIN (60”) x1
EF-WM348 XIN (72”) x1
EF-WM353 XIN (42”) x8
EF-WM350 XIN (50”) x8
EF-WM349 XIN (60”) x26
EF-WM348 XIN (72”) x32
EF-WM353 XIN (42”) x9
EF-WM349 XIN (60”) x13
EF-WM348 XIN (72”) x16
EF-WM353 XIN (42”) x4
EF-WM349 XIN (60”) x4
EF-WM348 XIN (72”) x4
EF-WM349 XIN (60”) x6
EF-WM348 XIN (72”) x8
F- Drywall AnchorsD- Mounting Bracket
L- Cord Cover
E- Wood Screws
A- Fireplace B- Side Brackets
OPTIONAL
For kit of OPTIONAL
parts J, K, L
(Item No: EF-WC)
contact:
1-800-561-5550
OPTIONALOPTIONAL
C1 - Top/Bottom Brackets C2 - Top/Bottom Brackets
G- ST4x12 Metal Screws
I- Crystals
J- Cord Corner K- Cord Corner
H- Remote Control
Hardware Parts List
03.16.21
EF-WM350 XIN (50”) x1 EF-WM350 XIN (50”) x4
EF-WM350 XIN (50”) x13
EF-WM353 XIN (42”) x1
EF-WM349 XIN (60”) x1
EF-WM348 XIN (72”) x1
EF-WM350 XIN (50”) x1
EF-WM353 XIN (42”) x1
EF-WM349 XIN (60”) x1
EF-WM348 XIN (72”) x1
EF-WM350 XIN (50”) x1 EF-WM353 XIN (42”) x1
EF-WM349 XIN (60”) x1
EF-WM348 XIN (72”) x1
EF-WM350 XIN (50”) x1
EF-WM349 XIN (60”) x6
EF-WM348 XIN (72”) x8
EF-WM353 XIN (42”) x9
EF-WM349 XIN (60”) x13
EF-WM348 XIN (72”) x16
EF-WM350 XIN (50”) x13
EF-WM353 XIN (42”) x2
EF-WM350 XIN (50”) x2
EF-WM349 XIN (60”) x2
EF-WM348 XIN (72”) x2
EF-WM353 XIN (42”) x2
EF-WM350 XIN (50”) x2
EF-WM349 XIN (60”) x2
EF-WM348 XIN (72”) x2
J
EF-WM353 XIN (42”) x4
EF-WM350 XIN (50”) x4
K
EF-WM349 XIN (60”) x5
EF-WM348 XIN (72”) x5

Page 6
Locating Appliance
DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF
TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,
CLOTHES AND CURTAINS AT LEAST 36” FROM THE FRONT OF THE APPLIANCE.
NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER
WATER CONTAINER.
WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND
MAINTENANCE.
TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE
MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED
OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.
DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)
WARNING
03.16.21
This appliance is for use on 120 Volts. The cord
has a plug as shown in (A).
To disconnect appliance, turn controls to off, then
remove plug from outlet.
(A)
GROUNDING METHODS
Grounding Appliance
GROUNDING PIN
COVER OF
GROUNDED
OUTLET BOX

Page 7
Installation
Minimum Clearance to Combustibles
Minimum Mantel Clearances
RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE
CORD TO AVOID TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PERSONAL INJURY. DO NOT RUN CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW
RUGS, RUNNERS OR THE LIKE. ARRANGE CORD AWAY FROM TRAFFIC AREAS AND WHERE IT
WILL NOT BE TRIPPED OVER.
RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY
MANNER. DO NOT USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.
RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED
OPTIONAL ACCESSORIES. USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR
THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR RESULT IN A SAFETY HAZARD.
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE
GASOLINE OR OTHER FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.
HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY
CREATE A FIRE HAZARD.
DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION.
WARNING
WARNING
Your JR42/50/60/72 unit is a wall-mounted appliance. Select a suitable location that is not susceptible to
NOTE: Follow all National and local electrical codes.
Bottom
Sides
Back
0”
0”
0”
Top
Top
Measurements are taken from the glass front
8” (203mm) to mantel
8” (203mm) to ceiling
03.16.21

Page 8
No Recess:
- Easy installation
- Full use of backlight
- Easy maintenence
For installation
instructions refer
to Page 12
Adjustable Mounting Brackets and Installation Options
Full Recess:
- Flush to wall look
- No use of backlight
For installation
instructions refer
to Page 9
Partial Recess:
- 1” gap for multi-use
- No use of backlight
- Easy maintenence
For installation
instructions refer
to Page 9
FIG. 2
SIDE
VIEW
TOP
VIEW
PARTS
NEEDED
4.GIF3.GIF
avoid exposed insulation or vapour barriers coming in contact with the appliance. This will ensure
clearance to combustibles is maintained.
OPTION 1 OPTION 2 OPTION 3
B + C1 or C2
)ylnoB:05RJ/24RJ()ylnoB:05RJ/24RJ(
B + C1 or C2D
03.16.21

Page 9
Option 1: Recessing the Appliance Flush into the Wall
builder before you install this appliance in the wall.
Select a location that is not prone to moisture and is located at least 36” (914mm) away from combustible
materials such as curtain drapes, furniture, bedding, paper etc.
C1 or C2
B
1. Measure the appliance and create a rough in
with electrical.
2. Remove the front glass (refer to Page 14 for
instructions).
3. Remove the LED back lights (refer to Page 15
for instructions).
4.
framing.
5. To fully recess the appliance into the wall:
A. Position and screw the side Builder’s
brackets (shown in grey on Page 10) to the set
of holes closest to the front glass as in Figure 2
on Page 8.
B. Use 8-24 screws (provided) to lock appliance
into wall from the side facing out.
C. Install the media and reinstall the glass front.
6. To partially recess the appliance into the
wall (Option 3):
A. Position and screw the side Builder’s
brackets (shown in grey on Page 10) to the
second set of holes from the front glass as in
Figure 4 on Page 8.
B. Use 8-24 screws (provided) to lock appliance
into wall from the side facing out.
C. Install the media and reinstall the glass front.
NOTE: Two sets of holes are provided for
recessing into the wall. The wall structure
may limit how far the appliance can be
recessed. Use the appropriate set of holes
when recessing to the frame, it may be
necessary to use the four holes on the top
and bottom.
FRONT VIEW
03.16.21

Page 10
Positioning of Adjustible Builder’s Brackets
EF-WM353 XIN,
EF-WM349 XIN
Builder’s bracket positions
shown in grey for each model
EF-WM348 XIN
B: Side brackets
C1: Top bracket (Tall)
Use for more security & surface area
C2: Top bracket (Short)
Will stay hidden behind glass.
B
B
B
C2
C2
03.16.21
EF-WM350 XIN,

Page 11
Minimum Clearance to Combustibles
Framing
Sides, back and top 0”
Measurements are taken from the glass front
EDCA.oNmetIB
EF-WM353
EF-WM349
EF-WM348
Recommended Framing Dimensions
Finishing Material
(NON-LOAD
BEARING)
A
A
B
B
19.3” (49cm) 38.60” (98cm)
19.3” (49cm) 56.60” (143.8cm)
21.27” (52.8cm) 68.60”
4.2”
4.2”
4.2”
18.8”
18.8”
18.8”
36.10”
54.10”
66.10”(174.2cm)
NOTE to installer: Please allow extra clearance for the power cord and easy installation.
TOP VIEWSIDE VIEW
E
D
C
03.16.21
EF-WM350 19.3” (49cm) 46.60” (118.4cm) 4.2” 18.8” 44.10”
XIN
XIN
XIN
XIN

Page 12
Option 2: Hanging the Appliance on the Wall
Due to the many different materials used on different walls, it is highly
recommended that you consult your local builder before you install this
appliance on the wall.
1. Select a location that is not prone to moisture and is located at
least 36” (914mm) away from combustible materials such as curtain
drapes, furniture, bedding, paper, etc.
2. Have two people hold the appliance against the wall to determine the
location.
3. Remove the bracket from the back of the unit by removing the two
screws, refer to Figure 1.
4. Mark out location, then mount the bracket onto the wall using the 8
supplied screws. This bracket MUST have the hooks facing upward
and be level.
WALL MOUNT
BRACKET
SCREWS
HOOK
HOOK
NOTE: It is strongly recommended
that the mounting bracket be
screwed into the wall studs where
possible. If the wall studs cannot
be used, ensure that the supplied
plastic anchors are used to the
bracket to the wall and the bracket
is adequately secured.
5. With the wall mounting bracket installed have two people lift the appliance up and insert the two
hooks on the bracket into the two slots on the back of the appliance.
6. Check the appliance for stability ensuring that the bracket will not pull free from the wall.
BODY
FRONT
GLASS
SIDE VIEW
Figure 1
Bracket
03.16.21

Page 13
1. Remove the cover plate from the right side of the appliance by removing the four screws, as shown above.
2. Remove the wire connectors from the power cord. The power cord may be discarded.
3. Take the new cover plate, supplied in the manual bag. Punch out the 7/8” (22mm) hole and install a box
connector through, into the junction box. Snap the box connector clamp onto the supply wires.
4. Using the wire connectors, connect the ground green wires (G) and white wires (N) together, then hot
black wires (L) and then refer to Figure 2.
5. Reinstall the cover plate using the four screws, as shown in Figure 1.
NOTE: Leave enough wire so that the appliance can be removed from the enclosure without
disconnecting the power supply.
HARD WIRING CONNECTION
wire the appliance directly to the house hold wiring.
This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In
the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the
current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
COVER PLATE
Figure 1
Figure 2
Hard Wiring Installation
TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED
SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
WARNING
GN
L
03.16.21

Page 14
1. Remove the 4 screws from the sides of the appliance in Figure 1.
2. Have two people lift the glass up and away from the appliance, holding the glass vertical while carrying.
Carefully rest the glass on a soft, non-abrasive surface.
3. Install the crystal embers (refer to instructions on Page 15)
4. Re-install the front glass by aligning the slots with the pins on the side of the appliance. Press the glass
down to secure in place.
5. Secure the front glass using the 4 screws in Figure 1. (If fully recessed, this is not necessary)
Front Glass Removal / Installation
POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID RECONSTRUCTION.
HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.
BEFORE THE FRONT GLASS IS INSTALLED OR REMOVED, UNPLUG THE APPLIANCE AND WAIT UNTIL
APPLIANCE IS COOL TO THE TOUCH. GLASS CAN BE HEAVY AND FRAGILE SO HANDLE WITH CARE.
WARNING
WARNING
FinishingFinishing
Figure 1
03.16.21

Page 15
The glass front must be removed and the appliance must be secured in its location before the crystal
embers are installed.
Carefully place crystal embers into the bottom media tray on the front of the appliance as illustrated.
Apply an even layer from side to side.
LED Back Light Removal
1. Unscrew the two screws in Figure A.
2. Lift off the LED cover and remove in Figure B.
3. Disconnect the wires where connected to the circuit board in Figure C.The disassembly is complete.
Crystal embers and Log set Installations
03.16.21
1.Crystal installation
2.Log set installation
Apply an even layer of crystal from side to side , randomly place the log (J logs or K logs, refer to page 5)
pieces included in the packaging on top of the crystal medias. Use the crystal to fill in spaces between the
logs. This will improve the overall look of the fireplaces.
EF-WM353 XIN (42") x4 (J logs)
EF-WM350 XIN (50") x4 (J logs)
EF-WM349 XIN (60") x5 (K logs)
EF-WM348 XIN (72") x5 (K logs)
Figure A Figure B Figure C

Page 16
Main Power Switch
Operating with Touch Panel
Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.
NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power
failure, the appliance will lose its memory function and will reset to factory mode when the power
returns.
To turn unit power on:
1. Plug in power cord.
2. Turn on the power switch (located on the front bottom right side of the appliance).
3. Verify the power is turned on when two ring tones are initiated.
The unit can be controlled by either the touch panel controls which are located on the right side of the front
glass or the remote control.
1.
Operating Instructions
WHILE THE APPLIANCE IS OPERATING DO NOT REMOVE THE GLASS PANEL. THIS WILL CAUSE THE
REMOTE CONTROL AND TOUCH PANEL TO DISFUNCTION.
WARNING
ON/OFF
Power
Flame
Timer
Heater
Indicator
03.16.21
: Press power on/off button. Fireplace is turned on. LED displays " ".
: Heater is .Flame at the brightest level ( )with red/blue/yellow flame on. Backlight is
on with red/blue/yellow flame on. Backlight is on with red/yellow/ blue combination ( ). Ember bed color
: Press button multiple times to cycle through 4 different brightness levels
1.
2.
and OFF for all the flame color options(Red, Yellow, Blue), display
: Press " " multiple times to set the operating duration to 30 min, 1h, 2h, 3h, 4h, 5h, 6h, 7h,
3.
8h, 00(timer off) respectively.
: Press " " key: set the required room temperature. The parameters is pre-set
4.
in degrees Celsius16-19-21-23-25-27-30-OFF (indicate H0) as a repeat circulation.
Press key for 5 seconds, then a single "beep" sound will be heard which indicates the temperature switches
to Fahrenheit degree. The parameter is set to Fahrenheit degree of 61-66-70-73-77-80-86-OFF (indicate )
as a repeat circulation.
is white( ).
Fireplaces ON and OFF ON
Initial setting OFF F4
C3
C3
Flame Brightness adjustment
F4-F3, F2, F1,FO.
Timer function
Heater temperature setting
HO

Operating with Touch Panel
: When product on heater lock mode, press the again and hold for 5 seconds, the heater
6.
function will be unlocked and will display " ". Heater and related temperature setting function is activated. Heater
operation is back to normal status.
: Press " "button and hold for 5 seconds, the heater and related temperature setting button
5.
will be locked. The heater will be in "OFF" mode and heater function is disabled, which means the heater cannot be
turned on unless preform "heater unlock" operation. " " will display when the heater is in the locked mode.
Page 17
03.16.21
Note:The touch panel buttons will glow when pressed,the glow will fade in 5 seconds.
Heater Lock Feature
LO
Heater unlock Feature
UL
Flame and timer button operation will remain normal while the heater is locked or unlocked.
If the heater is ON , and flame is OFF , display shows current heater setting (H1 or H2), the display will
not disappear until the flame is turned on.
“”“”
App operation will not be effected by lock or unlock feature.
“”“”
Heater lock function is a useful feature for those families with children, or for public commercial areas that
“”
need the heating function.
don'tdon't

WiFi APP Installation Procedure
Available for Android and iOS, the Smart Flame Connect app can be used to control your
1. Create an Account
2. Fireplace WiFi Setup
•
-
•
•
3. Check for Firmware Update
4. Controls via 4G/LTE Mobile Networks
Flame Connect for Aplle i
H OM E
Page 18 03.16.21
5. APP installation
Scan the QR code for the latest smart
NOTE:
More help? https://www.jrhome.com/
flame connect App support.
app-smart-flame-connect-techsup/

Page 19
Multi-functional Operating with Remote Control
Turning ON/OFF the fireplace:
03.16.21
1.Ensure the fireplace is at "power on" status. (refer to " " on page 16).
Main Power Switch
2.Press power on/off button to turn on the fireplace. LED displays " ".
ON
3.Initial setting: Heater is off. Flame at the brightest level with red/blue/yellow flame on.
Backlight is on with red/yellow/ blue combination. Ember bed color is white.
Note: if the fireplace is turned off by using remote control, when
turning on the fireplaces by using the remote control, the existing flame, ember, backlight
will resume to the previous setting.
Memory setting feature
Flame, ember and backlight color changing:
Ensure fireplaces displays " " mode.
ON
button can turn on/off the flame, ember and backlight
All light source ON/OFF :
simultaneously.
Press the " " button multiple times to cycle yellow color flame through 4 different
FF On mode will display .
FO
1. Flame color options:
Off mode will display and
brightness levels , y4-y3-y2-y1-y0, with y4 (the brightest), y0 (OFF)
Press the " " button multiple times to cycle yellow color flame through 4 different
brightness levels ,b4-b3-b2-b1-b0, with b4(the brightest), b0 (OFF)
Press the " " button multiple times to cycle yellow color flame through 4 different
brightness levels , r4-r3-r2-r1-r0, with r4(the brightest), r0 (OFF)
2. Timer options: Press the " " button multiple times to set operating timing duration to
30min, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h, 00
3. Backlight color options: Press the " " button multiple times to cycle the back LED
lights through red (C1), red/blue (C2),red/yellow/blue (C3),yellow/blue (C4),blue (C5),
yellow (C6),red/yellow( C7), fade (CE),OFF (C0)
Icon Display
Red
Red/Blue
Red/Yellow/Blue
Yellow/Blue
Blue
Yellow
Red/Yellow
Auto rotating
Off
C1
C2
C3
C4
C5
C6
C7
CE
CO
Backlight setting

Multi-functional Operating with Remote Control
4. Ember bed color options: Press button multiple times to cycle through the ember bed color from red(E1),
pink(E2),snow white(E3), cool blue(E4), dark blue(E5), green(E6), lake green(E7), auto rotating(EE), off(EO):
Icon Display
Red
Pink
Snow white
Cool blue
Dark blue
Green
Lark green
Auto rotating
Off
E1
E2
E3
E4
E5
E6
E7
EE
EO
Ember bed light setting
Page 20 03.16.21
NOTE: Flame, ember, backlight can be controlled individually.
5. Heater control options:
1. Ensure fireplaces displays " " mode
ON
2. Press the " "heater ON/OFF. When press once, the heater is ON with high temperature status. Two
groups of heating system will be turned ON at 1500W by displaying " ". When press button again,
the heater will be turned off,
H2
3. Press " " button. This operation will decrease the temperature setting with low temperature status. One
group of heating system will be turned on at 750W by displaying .
H1
NOTE: Pressing the a second time will turn off the heater.
or
””
””
6.Temperature control options:
Press the " " key to set the required room temperature. The parameters is pre-set in degrees Celsius
16-19-21-23-25-27-30-HO (indicate HO) as a repeat circulation.
Press key and hold for 5 seconds, a "beep" sound will be heard, which indicates a switch to Fahrenheit
degree of 61-66-70-73-77-80-86-HO (indicate HO) as a repeat circulation.
7.Heater lock and unlock control option:
Heater lock by using remote: Press " "button and hold for 5 seconds, the heater and related
temperature setting button will be locked. The heater will be in "OFF" mode and heater function is disabled,
which means the heater cannot be turned on unless preform "heater unlock" operation. " " will display
LO
Heater unlock by using remote:
when the heater is in the locked mode.
When the unit is in heater lock mode, press the key again and hold for
5 seconds, the heater function will be unlocked and will display " ". Heater and related temperature setting
function is activated. Heater operation is back to normal status.
UL
Heater lock function is a useful feature for those families with children, or for public commercial areas that
need the heating function.
""
don'tdon't
Flame and timer button operation will remain normal while the heater is locked or unlocked
If the heater is ON and flame is OFF, display shows current heater setting (H1 or H2), the
"" ""
display will not disappear until the flame is turned on.
App operation will not be effected by lock or unlock feature.
""" "
displaying " ".
HO